Ruijie RG-S6220-48XS6QXS-H Installation and operating manual

RG-S6220-H Series Switches
Hardware Installation and Reference Guide V1.08

Copyright Statement
Ruijie Networks©2017
Ruijie Networks reserves all copyrights of this document. Any reproduction, excerption, backup, modification,
transmission, translation or commercial use of this document or any portion of this document, in any form or by any means,
without the prior written consent of Ruijie Networks is prohibited.
Exemption Statement
This document is provided “as is”. The contents of this document are subject to change without any notice. Please obtain
the latest information through the Ruijie Networks website. Ruijie Networks endeavors to ensure content accuracy and will
not shoulder any responsibility for losses and damages caused due to content omissions, inaccuracies or errors.

Preface
Thank you for using our switches. This guide will help you install and use the switches.
Scope
This manual describes the functions and physical features of the switches, and presents the installation procedure,
troubleshooting procedure, technical specifications, and specifications and usages rules of cables and connectors. It is
intended for the users that have some experience in installing and maintaining network hardware and want to learn the
above information. At the same time, it is assumed that the users of this switch are already familiar with the related
terms and concepts of Ethernet.
Document Structure
Chapter 1 "Product Overview" describes the main characteristics, technical specifications, and related modules
of this product.
Chapter 2 "Preparation before Installation" lists the safety, power supply, and site requirements that must be
met before the switch can be installed.
Chapter 3 "Product Installation" describes how to install the integrated switch and modules, and connect its
power cables and grounding lines.
Chapter 4 "System Debugging" describes the commissioning after the switch is powered on for the first time.
Chapter 5 “Monitoring and Maintenance”
Chapter 5 "Troubleshooting" describes possible problems met during the installation and use of the switch and
solutions for such problems.
Appendix A "Connector and Connection Media"
Appendix B "Mini-GBIC, 10G and 40G Modules"
Appendix C “Lightening Protection”
Appendix D “Cabling Recommendations in Installation”
Appendix E “Site Selection”
Appendix F “Mini USB Console Driver Installation”
Obtaining Technical Assistance
Ruijie Networks website: http://www.ruijienetworks.com/
Service Email: [email protected]
Technical Support: http://www.ruijienetworks.com/service.aspx
Technical Support Hotline: [phone]
Related Documents
Documents
Description
Configuration Guide
Describes network protocols and related mechanisms that supported by the
product, with configuration examples.

Command Reference
Describes the related configuration commands, including command modes,
parameter descriptions, usage guides, and related examples.
Symbol Conventions
Means reader take note. Notes contain helpful suggestions or references.
Means reader be careful. In this situation, you might do something that could result in equipment damage or loss
of data.

Hardware Installation and Reference Guide Product Overview
1 Product Overview
Ruijie S6220-H series switches are the data center-oriented high-density 10G layer 3 IPv6 box switches. They are
mainly applicable to the data center to provide the convergence access for the servers.
The RG-S6220-H Series Switches:
Model
10G
SFP+
Ethernet
Port
10GBase-T
Ethernet
Port
40G
QSFP+
Ethernet
Port
2/4/8G
SFP
FC
Interface
Extension
Module
Slot
Redundant
Fan
Redundant
Power
Supply
RG-S6220-48XS6QXS-H
48
N/A
6
N/A
N/A
2+1
1+1
RG-S6220-48XT6QXS-H
N/A
48
6
N/A
N/A
2+1
1+1
RG-S6220-32QXS-H
N/A
N/A
32
N/A
N/A
2+1
1+1
An SFP+ port supports both 10GBASE-R and 1000BASE-X.
A QSFP+ port support both 40G mode and 4 x 10G mode.
10GBASE-T is downward compatible with 1000BASE-T and 100BASE-TX in full-duplex mode.
1.1 RG-S6220-48XS6QXS-H
Specifications
Model
RG-S6220-48XS6QXS-H
CPU
Quad-core processer, 1.0GHz
BOOT ROM
8MB
FLASH Memory
1GB
SDRAM
DDRIII 2GB
Extension Module
Slot
Unsupported
Extension Module
Unsupported
Fan Slot
3 (support 2+1 redundancy, configure at least 2 fan modules in one switch)
Fan Module
M6220-FAN II-F, M6220-FAN II-R
Power Supply
Slot
2 (support 1+1 redundancy)
Power Module
RG-M6220-AC460E-F, RG-M6220-AC460E-R
Power Supply
Input
AC input
Rated voltage range: 100V AC to 240V AC
Maximum voltage range: 90V AC to 264VAC
Frequency: 50 Hz to 60 Hz
Rated current: 5.29 A to 2.2A
High voltage direct current (HVDC) input:
Input voltage range: 192V DC to 290V DC
Input current range: 2.66A to 2.03A

Hardware Installation and Reference Guide Product Overview
Power
Consumption
Less than 250 W
Optical Module
Refer to Appendix B
The supported modules update at any time, contact Ruijie Networks for details.
SFP+ Port
Supported
QSFP+ Port
Supported
FC Port
Unsupported
10GBASE-T Port
Unsupported
Temperature
Warning
Support temperature warning and over-temperature protection.
EMC Standards
GB9254-2008 CLASS A
Safety Standards
GB4943-2011
Working
Temperature
0°C to 50°C (32ºF to 122ºF)
Storage
Temperature
-40°C to 70°C (-40ºF to 158ºF)
Working Humidity
10% to 95% RH (non-condensing)
Weight
Net weight: 9.5 kg (including 3 fan modules and 2 power modules)
Dimensions
(L x W x H)
440 mm x 420 mm x 44 mm, 1U
RG-S6220-H switch is a class A product. In a domestic environment, this product may cause radio interference in
which case the user may be required to take adequate measures.
The 10G or 40G Ethernet port of the RG-S6220-48XS6QXS-H switch supports DAC. The SFP+ port supports
1-meter, 3-meter and 5-meter cable, and the QSFP+ port supports 3-meter cable. For a detailed model and
specification, refer to Appendix B.
RG-S6220-48XS6QXS-H-R contains one RG-S6220-48XS6QXS-H host, three M6220-FAN II-R fan modules, two
power slots without power modules (RG-M6220-AC460E-R).
RG-S6220-48XS6QXS-H-AC contains one RG-S6220-48XS6QXS-H host, three M6220-FAN II-F fan modules,
two RG-M6220-AC460E-F power modules.
Product Appearance
The hardware of the RG-S6220-48XS6QXS-H includes the chassis, the power supply system and the heat dissipation
system.
The power supply system: Provides two power supply slots, which support 1+1 power supply redundancy. It is
recommended users configure power supply redundancy.
The heat dissipation system: Provides three fan module slots, which support 2+1 fan redundancy. It is
recommended users configure all fans redundancy.
Figure 1-1 Appearance of the RG-S6220-48XS6QXS-H

Hardware Installation and Reference Guide Product Overview
Front Panel
Figure 1-2 Front Panel of the RG-S6220-48XS6QXS-H
Notes:
1. Switch status indicator
2. Switch locator indicator
3. SFP+ port status indicator
4. SFP+ port
5. QSFP+ port status indicator
6. QSFP+ port
The RG-S6220-48XS6QXS-H supports 10G SFP+ module and 1G SFP module. But the 10G SFP+ module
cannot function as the 1G SFP module.
Back Panel
Figure 1-3 Back Panel of the RG-S6220-48XS6QXS-H
Notes:
1. Power supply module slot
2. Fan module slot
3. MGMT port
4. MGMT port indicator
5. Switch locator indicator
6. Grounding connector
7. USB 2.0 port
8. Console port
9. MiniUSB port
10. Switch status indicator
11. Asset management label
Asset Management Label

Hardware Installation and Reference Guide Product Overview
The asset management label is next to the switch status indicator of the switch back panel. The label is movable and
can be withdrawn from the device. Users can mark the information such as asset name, category, code and registration
date on the label which helps to improve asset management accuracy and efficiency.
Figure 1-4 Asset Management Label of the RG-S6220-48XS6QXS-H
External Ports
The RG-S6220-48XS6QXS-H provides the following ports:
Universal serial bus (USB) port: This port can connect with USB memory to save logs, host versions, warnings
and other diagnostic messages. Therefore, it is more convenient to upgrade the software version of the switch on
line and save the log information.
MiniUSB port: This port can be used as a serial port after PC is installed with the required driver. For the driver
installation guide, refer to Appendix F.
To protect the data and avoid device damage, use qualified USB flash disks of good brands. At the same time, the
local USB port is compatible with most of the USB controllers except some USB flash disks.
RG-S6220-H series switches supports debugging, configuration, maintenance, management and host software
uploading of both Console and MiniUSB ports. But the Console port and the MiniUSB port cannot take effect in the
meanwhile.
Console port: Use RS-232 interface electrical level and standard RJ45 connector. This interface is connected with
the serial port of terminal PC to perform system debugging, configuration, maintenance, management, and host
software uploading.
MGMT port: This is an out-band Ethernet port, which uses standard RJ45 connector. This interface is connected
with Ethernet port of a PC to perform program downloading.
SFP+ port: There are 48 10G SFP+ ports, which support optical modules and DAC copper cables, and are
compatible with 1000BASE-X.
QSFP+ port: There are six 40G QSFP+ ports, which support optical modules and DAC copper cables. This port
can work in 4x10G mode.
Indicator

Hardware Installation and Reference Guide Product Overview
Indicator
Panel
Identification
Status
Meaning
Switch status indicator
(Front panel/Back
panel)
Status
Off
The system is not powered up.
Solid red
1) One of the modules of the system fails.
2) There are less than 2 fans.
3) The internal or partial temperature exceeds the
warning working temperature, and the switching
service resets.
Blinking green.
The system is initializing.
Solid green
The system is operational.
Solid yellow
1) The temperature gets to the warning threshold.
2) Only 2 fans are in the position.
3) One of the dual powers is not connected with the
AC power cord.
Switch locator indicator
(Front panel/Back
panel)
ID
Off
Device location is disabled.
Solid blue
Device location is enabled.
MGMT port indicator
MGMT
Off
The port is not connected.
Green
The port is connected at 1000Mbps.
Yellow
The port is connected at 10M/100M bps.
Blinking
The port is transmitting or receiving data.
SFP+ port status
indicator
1F-48F
Off
The port is not connected.
Solid green
The port is connected at 10G/1G bps.
Blinking green.
The port is transmitting or receiving data.
QSFP+ port status
indicator
49F-54F
(4 x 10G
mode)
Off
The port is not connected.
Solid green
The port is connected at 10Gbps.
Blinking green.
The port is transmitting or receiving data.
49F-54F
(1 x 40G
mode)
Off
The port is not connected.
Solid green
The port is connected at 40Gbps.
Blinking green.
The port is transmitting or receiving data.
Power Supply
The RG-S6220-H series switches support power supply the RG-M6220-AC460E-F. The smart power supply module
supports power management, and the host can read input power, input current, and temperature in real time. The
power supply module supports hot swapping.
The RG-S6220-H series switches support 1+1 power supply redundancy. To improve the stability and reliability of
the entire system, it is recommended to configure 1+1 power supply redundancy. When the two power supply
modules work normally, the switch is in the status of current sharing.
It requires at least one power supply module to work normally. Filler panels need to be installed in the unoccupied
power supply module slots to ensure ventilation and heat dissipation and avoid dusts.
Heat Dissipation

Hardware Installation and Reference Guide Product Overview
The working temperature of the RG-S6220-48XS6QXS-H switches is 0ºC to 50ºC, or 32ºF to 122ºF, and the heat
dissipation design needs to ensure the stability, safety and maintainability in such environment. The RG-S6220-H
series switches adopt fan ventilation and forced convection to ensure the device can work normally in specified
environment. Dust the device every three months to avoid blocking the ventilation openings.
The RG-S6220-48XS6QXS-H supports fan module M6220-FAN II-F and M6220-FAN II-R and provides fan speed
regulation, fan failure warning, and fan hot swapping.
Figure 1-5 Ventilation and Heat Dissipation of the RG-S6220-48XS6QXS-H
Figure 1-6 Ventilation and Heat Dissipation of the RG-S6220-48XS6QXS-H
Leave sufficient space in the front and at the back of the chassis (at least 20 cm) for ventilation.
It requires at least two fan modules to work normally. Filler panels need to be installed in the unoccupied fan
module slots to ensure ventilation and heat dissipation and avoid dusts.
1.2 RG-S6220-48XT6QXS-H
Specifications
Model
RG-S6220-48XT6QXS-H
CPU
Quad-core processer, 1.0GHz
BOOT ROM
8MB
FLASH Memory
1GB
SDRAM
DDRIII 2GB
Extension Module
Slot
Unsupported

Hardware Installation and Reference Guide Product Overview
Extension Module
Unsupported
Fan Slot
3 (support 2+1 redundancy, configure at least two fan modules in one switch)
Fan Module
M6220-FAN-F
Power Supply
Slot
2 (support1+1 redundancy)
Power Module
RG-M6220-AC460E-F
Power Supply
Input
AC input
Rated voltage range: 100V AC to 240V AC
Maximum voltage range: 90V AC to 264V AC
Frequency: 50 Hz to 60 Hz
Rated current range: 5.29A to 2.2A
High voltage direct current (HVDC) input:
Input voltage range: 192V DC to 290V DC
Input current range: 2.66A to 2.03A
Power
Consumption
Less than 424 W
Optical Module
Refer to Appendix B
The supported modules update at any time, contact Ruijie Networks for details.
SFP+ Port
Unsupported
QSFP+ Port
Supported
FC Port
Unsupported
10GBASE-T Port
Supported
Temperature
Warning
Support temperature warning and over-temperature protection.
EMC Standards
GB9254-2008 CLASS A
Safety Standards
GB4943-2011
Working
Temperature
0°C to 45°C (32ºF to 113ºF)
Storage
Temperature
-40°C to 70°C (-40ºF to 158ºF)
Working Humidity
10% to 95% RH (non-condensing)
Weight
Net weight: 11 kg (including 3 fan modules and 2 power modules)
Dimensions
(L x W x H)
440 mm x 500 mm x 44 mm, 1U
RG-S6220-H switch is a class A product. In a domestic environment, this product may cause radio interference in
which case the user may be required to take adequate measures.
The 40G Ethernet port of the RG-S6220-48XT6QXS-H switch supports 3-meter DAC. For a detailed model and
specification, refer to Appendix B.
Product Appearance
The hardware of the RG-S6220-48XT6QXS-H includes the chassis, the power supply system and the heat dissipation
system.
The power supply system: Provides two power supply slots, which support 1+1 power supply redundancy. It is
recommended users configure power supply redundancy.

Hardware Installation and Reference Guide Product Overview
The heat dissipation system: Provides three fan module slots, which support 2+1 fan redundancy. It is
recommended users configure all fans redundancy.
Figure 1-7 Appearance of the RG-S6220-48XT6QXS-H
Front Panel
Figure 1-8 Front Panel of the RG-S6220-48XT6QXS-H
Notes:
1. Switch status indicator
2. locator status indicator
3. 10GBASE-T port status indicator
4. 10GBASE-T port
5. QSFP+ port status indicator
6. QSFP+ port
The RG-S6220-48XT6QXS-H supports 10GBASE-T, 1000BASE-T and 100BASE-TX operating modes.
Back Panel
Figure 1-9 Back Panel of the RG-S6220-48XT6QXS-H

Hardware Installation and Reference Guide Product Overview
Notes:
1. Power supply module slot
2. Fan module slot
3. MGMT port
4. MGMT port status indicator
5. Switch locator status indicator
6. Grounding connector
7. USB 2.0 port
8. Console port
9. MiniUSB port
10. Switch status indicator
11. Asset management label
Asset Management Label
The asset management label is next to the switch status indicator of the switch back panel. The label is movable and
can be withdrawn from the device. Users can mark the information such as asset name, category, code and registration
date on the label which helps to improve asset management accuracy and efficiency.
Figure 1-10 Asset Management Label of the RG-S6220-48XT6QXS-H
External Interface
The RG-S6220-48XT6QXS-H provides the following interfaces:
Universal serial bus (USB) port: This port can connect with USB memory to save logs, host versions, warnings
and other diagnostic messages. Therefore, it is more convenient to upgrade the software version of the switch on
line and save the log information.
MiniUSB port: This is a communication serial port that applies the electrical level of the USB port and a MIniUSB
connector. This port is connected with the USB port of terminal PC to perform system debugging, configuration,
maintenance, management and host software uploading.
To protect the data and avoid device damage, use qualified USB flash disks of good brands. At the same time, the
local USB port is compatible with most of the USB controllers except some USB flash disks.
RG-S6220-H series switches supports system debugging, configuration, maintenance, management and host
software uploading of both Console and MiniUSB ports. But the Console port and the MiniUSB port cannot take
effect in the meanwhile.
Console port: Use RS-232 interface electrical level and standard RJ45 connector. This interface is connected with
the serial port of terminal PC to perform system debugging, configuration, maintenance, management, and host
software uploading.
MGMT port: This is an out-band Ethernet port, which uses standard RJ45 connector. This port is connected with
Ethernet port of a PC to perform program downloading.

Hardware Installation and Reference Guide Product Overview
10GBASE-T port: There are 48 10GBASE-T ports, which are downward compatible with 1000BASE-T and
100BASE-TX.
QSFP+ port: There are six 40G QSFP+ ports, which support optical modules and DAC. This port can work in
4x10G mode.
Indicator
Indicator
Panel
Identification
Status
Meaning
Switch status indicator
(Front panel/Back
panel)
Status
Off
The system is not powered up.
Solid red
1) One of the modules of the system fails.
2) There are less than N fans (N+1 redundant fan).
3) The internal temperature exceeds the warning
working temperature, and the switching service
resets.
Blinking green.
The system is initializing.
Solid green
The system is operational.
Solid yellow
1) The temperature gets to the warning threshold.
2) Only N fans are in the position (N+1 redundant
fan).
3) One of the dual powers is not connected with the
AC power cord.
Switch locator indicator
(Front panel/Back
panel)
ID
Off
Device location is disabled.
Solid blue
Device location is enabled.
MGMT port indicator
MGMT
Off
The port is not connected.
Green
The port is connected at 1000Mbps.
Yellow
The port is connected at 10M/100M bps.
Blinking
The port is transmitting or receiving data.
10GBASE-T port status
indicator
1-48
Off
The port is not connected.
Solid green
The port is connected at 10G/1G/100M bps.
Blinking green.
The port is transmitting or receiving data.
QSFP+ port status
indicator
49F-54F
(4 x 10G
mode)
Off
The port is not connected.
Solid green
The port is connected at 10Gbps.
Blinking green.
The port is transmitting or receiving data.
49F-54F
(1 x 40G
mode)
Off
The port is not connected.
Solid green
The port is connected at 40Gbps.
Blinking green.
The port is transmitting or receiving data.
Power Supply
The RG-S6220-H series switches support power supply the RG-M6220-AC460E-F. The smart power supply module
supports power management, and the host can read input power, input current, and temperature in real time. The
power supply module supports hot swapping.

Hardware Installation and Reference Guide Product Overview
The RG-S6220-H series switches support 1+1 power supply redundancy. To improve the stability and reliability of
the entire system, it is recommended to configure 1+1 power supply redundancy. When the two power supply
modules work normally, the switch is in the status of current sharing.
It requires at least one power supply module to work normally. Filler panels need to be installed in the unoccupied
power supply module slots to ensure ventilation and heat dissipation and avoid dusts.
Heat Dissipation
The working temperature of the RG-S6220-48XT6QXS-H switches is 0ºC to 45ºC, or 32ºF to 113ºF, and the heat
dissipation design needs to ensure the stability, safety and maintainability in such environment. The RG-S6220-H
series switches adopt fan ventilation and forced convection to ensure the device can work normally in specified
environment. Dust the device every three months to avoid blocking the ventilation openings.
The RG-S6220-48XT6QXS-H supports fan module M6220-FAN-F and provides fan speed regulation, fan failure
warning, and fan hot swapping.
Figure 1-11 Ventilation and Heat Dissipation of the RG-S6220-48XT6QXS-H
Leave sufficient space in the front and at the back of the chassis (at least 20cm) for ventilation.
It requires at least two fan modules to work normally. Filler panels need to be installed in the unoccupied fan
module slots to ensure ventilation and heat dissipation and avoid dusts.
1.3 RG-S6220-32QXS-H
Specifications
Model
RG-S6220-32QXS-H
CPU
Quad-core processer, 1.0GHz
BOOT ROM
8MB
FLASH Memory
1GB
SDRAM
DDRIII 2GB
Extension Module
Slot
Unsupported
Extension Module
Unsupported
Fan Slot
3 (support 2+1 redundancy, configure at least two fan modules in one switch)
Fan Module
M6220-FAN-F

Hardware Installation and Reference Guide Product Overview
Power Supply
Slot
2 (support 1+1 redundancy)
Power Module
RG-M6220-AC460E-F
Power Supply
Input
AC input
Rated voltage range: 100V AC to 240V AC
Maximum voltage range: 90 V AC to 264 V
AC
Frequency: 50 Hz to 60 Hz
Rated current range: 5.29A to 2.2A
High voltage direct current (HVDC) input:
Input voltage range: 192V DC to 290V DC
Input current range: 2.66A to 2.03A
Power
Consumption
Less than 250 W
Optical Module
Refer to Appendix B
The supported modules update at any time, contact Ruijie Networks for details.
SFP+ Port
Unsupported
QSFP+ Port
Supported
FC Port
Unsupported
10GBASE-T Port
Unsupported
Temperature
Warning
Support temperature warning and over-temperature protection.
EMC Standards
GB9254-2008 CLASS A
Safety Standards
GB4943-2011
Working
Temperature
0°C to 45°C (32ºF to 113ºF)
Storage
Temperature
-40°C to 70°C(-40ºF to 158ºF)
Working Humidity
10% to 95% RH (non-condensing)
Weight
Net weight: 9.0 kg (including 3 fan modules and 2 power modules)
Dimensions
(L x W x H)
442 mm x 420 mm x 44 mm, 1U
RG-S6220-H switch is a class A product. In a domestic environment, this product may cause radio interference in
which case the user may be required to take adequate measures.
The 40G Ethernet port of the RG-S6220-32QXS-H switch supports 3-meter DAC. For a detailed model and
specification, refer to Appendix B.
Product Appearance
The hardware of the RG-S6220-32QXS-H includes the chassis, the power supply system and the heat dissipation
system.
The power supply system: Provides two power supply slots, which support 1+1 power supply redundancy. It is
recommended users configure power supply redundancy.
The heat dissipation system: Provides three fan module slots, which support 2+1 fan redundancy. It is
recommended users configure all fans redundancy.

Hardware Installation and Reference Guide Product Overview
Figure 1-12 Appearance of the RG-S6220-32QXS-H
Front Panel
Figure 1-13 Front Panel of the RG-S6220-32QXS-H
Notes:
1. Locator status indicator
2. Link indicator of the MGMT port
3. MGMT port
4. Act indicator of the MGMT port
5. Status indicator of the QSFP+ port
6. Switch status indicator
7. USB 2.0 port
8. Console port
9. MiniUSB port
10. QSFP+ port
11. Status indicator of the QSFP+ port
The 40G QSFP+ port of RG-S6220-32QXS-H 5F-28F can work in 4×10G mode.
Back Panel
Figure 1-14 Back Panel of the RG-S6220-32QXS-H

Hardware Installation and Reference Guide Product Overview
Notes:
1. Power supply module slot
2. Fan module slot
3. Asset management label
4. Grounding connector
Asset Management Label
The asset management label is in the lower right corner of the switch back panel. The label is movable and can be
withdrawn from the device. Users can mark the information such as asset name, category, code and registration date
on the label which helps to improve asset management accuracy and efficiency.
Figure 1-15 Asset Management Label of the RG-S6220-32QXS-H
External Interface
The RG-S6220-32QXS-H provides the following interfaces:
Universal serial bus (USB) port: This port can connect with USB memory to save logs, host versions, warnings
and other diagnostic messages. Therefore, it is more convenient to upgrade the software version of the switch on
line and save the log information.
MiniUSB port: This port can be used as a serial port. A driver should be installed in the terminal PC. For more
information about the installation of drivers, please refer to Appendix F.
To protect the data and avoid device damage, use qualified USB flash disks of good brands. At the same time, the
local USB port is compatible with most of the USB controllers except some USB flash disks.
RG-S6220-H series switches support system debugging, configuration, maintenance, management and host
software uploading of both Console and MiniUSB ports. But the Console port and the MiniUSB port cannot take
effect in the meanwhile.
Console port: Use RS-232 interface electrical level and standard RJ45 connector. This interface is connected with
the serial port of terminal PC to perform system debugging, configuration, maintenance, management, and host
software uploading.
MGMT port: This is an out-band Ethernet port, which uses standard RJ45 connector. This port is connected with
Ethernet port of a PC to perform program downloading.
QSFP+ port: There are 32 40G QSFP+ ports, which support optical modules and DAC. Apart from ports 1F-4F
and 29F-32F, all such ports can be split into four 10G QSFP+ ports via software.
Indicator

Hardware Installation and Reference Guide Product Overview
Indicator
Panel
Identification
Status
Meaning
Switch status indicator
Status
Off
The system is not powered up.
Solid red
1) One of the modules of the system fails.
2) There are less than 2 fans.
3) The internal temperature exceeds the warning
working temperature, and the switching service
resets.
Blinking green.
The system is initializing.
Solid green
The system is operational.
Solid yellow
1) The temperature gets to the warning threshold.
2) Only 2 fans are in the position.
3) One of the dual powers is not connected with the
AC power cord.
Switch locator indicator
ID
Off
Device location is disabled.
Solid blue
Device location is enabled.
MGMT port indicator
MGMT
Off Link indicator
The port is not connected.
Yellow Link
indicator
The port is connected at 10M/100M/1000M bps.
Green Act
indicator
The port is connected at 10M/100M/1000M bps.
Blinking green Act
indicator
The port is transmitting or receiving data at
10M/100M/1000M bps.
QSFP+ port status
indicator
5F-28F
(4 x 10G
mode)
Off
The port is not connected.
Solid green
The port is connected at 10Gbps.
Blinking green.
The port is transmitting or receiving data.
1F-32F
(1 x 40G
mode)
Off
The port is not connected.
Solid green
The port is connected at 40Gbps.
Blinking green.
The port is transmitting or receiving data.
Power Supply
The RG-S6220-H series switches support power supply the RG-M6220-AC460E-F. The smart power supply module
supports power management, and the host can read input power, input current, and temperature in real time. The
power supply module supports hot swapping.
The RG-S6220-H series switches support 1+1 power supply redundancy. To improve the stability and reliability of
the entire system, it is recommended to configure 1+1 power supply redundancy. When the two power supply
modules work normally, the switch is in the status of current sharing.
It requires at least one power supply module to work normally. Filler panels need to be installed in the unoccupied
power supply module slots to ensure ventilation and heat dissipation and avoid dusts.
Heat Dissipation
The working temperature of the RG-S6220-32QXS-H switches is 0ºC to 45ºC or 32ºF to 113ºF, and the heat
dissipation design needs to ensure the stability, safety and maintainability in such environment. The RG-S6220-H

Hardware Installation and Reference Guide Product Overview
series switches adopt fan ventilation and forced convection to ensure the device can work normally in specified
environment. Dust the device every three months to avoid blocking the ventilation openings.
The RG-S6220-48XT6QXS-H supports fan module M6220-FAN-F and provides fan speed regulation, fan failure
warning, and fan hot swapping.
Figure 1-16 Ventilation and Heat Dissipation of the RG-S6220-32QXS-H
Leave sufficient space in the front and at the back of the chassis (at least 20cm) for ventilation.
It requires at least two fan modules to work normally. Filler panels need to be installed in the unoccupied fan
module slots to ensure ventilation and heat dissipation and avoid dusts.
1.4 Module
The RG-S6220-H series switches adopt modularization design. Strictly complying with the industrial standard, the
system modules are reasonably subdivided and the module interfaces are unified. All these ensure that the
RG-S6220-H series switches system is complete and all modules are independent.
The RG-S6220-H series switches support the following modules: M6220-AC460E-F, M6220-AC460E-R, M6220-FAN-F,
M6220-FAN II-F, and M6220-FAN II-R.
1.4.1 M6220-FAN-F
The M6220-FAN-F is the fan module of the RG-S6220-H series. The M6220-FAN-F provides heat dissipation system
and ensures system stability. The M6220-FAN-F supports speed regulation and hot swapping.
Module Appearance
Figure 1-17 Appearance of the M6220-FAN-F