Ruijie RG-S6510 Series Installation and operating manual

RG-S6510 (V2.0) Series Switches
Hardware Installation and Reference Guide

Copyright Statement
Ruijie Networks©2019
Ruijie Networks reserves all copyrights of this document. Any reproduction, excerption, backup, modification,
transmission, translation or commercial use of this document or any portion of this document, in any form or by anymeans,
without the prior written consent of Ruijie Networks is prohibited.
Exemption Statement
This document is provided “as is”. The contents of this document are subject to change without any notice. Please obtain
the latest information through the Ruijie Networks website. Ruijie Networks endeavors to ensure content accuracy and will
not shoulder any responsibility for losses and damages caused due to content omissions, inaccuracies or errors.

Preface
Thank you for using our switches. This guide will help you install and use the switches.
Scope
This manual describes the functions and physical features of the switches, and presents the installation procedure,
troubleshooting procedure, technical specifications, and specifications and usages rules of cables and connectors. It is
intended for the users that have some experience in installing andmaintaining network hardware and want to learn the
above information. At the same time, it is assumed that the users of this switch are already familiar with the related
terms and concepts of Ethernet.
Document Structure
Chapter 1 "Product Overview" describes the main characteristics, technical specifications, and related modules
of this product.
Chapter 2 "Preparation before Installation" lists the safety, power supply, and site requirements that must be
met before the switch can be installed.
Chapter 3 "Product Installation" describes how to install the integrated switch and modules, and connect its
power cables and grounding lines.
Chapter 4 "System Debugging" describes the commissioning after the switch is powered on for the first time.
Chapter 5 “Monitoring and Maintenance”
Chapter 5 "Troubleshooting" describes possible problems met during the installation and use of the switch and
solutions for such problems.
Appendix A "Connector and Connection Media"
Appendix B "10G, 25G, 40G and 100G Modules"
Appendix C “Lightening Protection”
Appendix D “Cabling Recommendations in Installation”
Appendix E “Site Selection”
Obtaining Technical Assistance
Ruijie Networks Website: https://www.ruijienetworks.com/
Technical Support Website: https://ruijienetworks.com/support
Case Portal: https://caseportal.ruijienetworks.com
Community: https://community.ruijienetworks.com
Technical Support Email: [e-mail]
Skype: [e-mail]
Related Documents
Documents
Description

Configuration Guide
Describes network protocols and related mechanisms that supported by the
product, with configuration examples.
Command Reference
Describes the related configuration commands, including command modes,
parameter descriptions, usage guides, and related examples.
Symbol Conventions
Means reader take note. Notes contain helpful suggestions or references.
Means reader be careful. In this situation, you might do something that could result in equipment damage or loss
of data.

Hardware Installation and Reference Guide Product Overview
- 3 -
1 Product Overview
RG-S6510 (V2.0) switches are data center oriented high density 10G/25G access switches, providing 25G/100G
access, low latency, and complete data center features. RG-S6510 (V2.0) switches, with up to 48 25G ports and 8
100G ports, can be used with RG-N18000-X/RG-S6500-4C switches to compose a high-performance and
high-reliability data center network.
The RG-S6510 (V2.0) Series Switches:
Model
100G
QSFP28
Ethernet
Port
25G/10G
SFP28
Ethernet
Port
10GBase-T
Ethernet Port
Extension
Module Slot
Redundant
Fan
Redundant
Power Supply
RG-S6510-48VS8CQ
8
48
N/A
N/A
3+1
1+1
An SFP28 port supports 25G/10Gbase-R and does not support 1000base-X.
A QSFP28 port supports both 100G/40G mode and 4x25G/4x10G mode.
Specifications
Model
RG-S6510-48VS8CQ
CPU
Quad-core processer, 1.2GHz
BOOT ROM
16MB
FLASH Memory
8GB
SDRAM
DDR4 4GB (Compatibility: 8GB)
Extension Module
Slot
Unsupported
Extension Module
Unsupported
Fan Slot
4 (support 3+1 redundancy, configure at least 3 fan modules in one switch)
Fan Module
M6510-FAN-F, M6510-FAN-R
Power Supply
Slot
2 (support 1+1 redundancy)
Power Module
RG-PA550I-F, RG-PA550I-R
Power Supply
Input
AC input
Rated voltage range: 100V AC to 240V AC
Maximum voltage range: 90V AC to 264V AC
Frequency: 50 Hz to 60 Hz
Rated current: 3.5Ato 7.2A
High voltage direct current (HVDC) input:
Input voltage range: 192V DC to 288V DC
Input current range: 3.6A
Power
Consumption
Less than 300W
Optical Module
Refer to Appendix B
The supported modules update at any time, contact Ruijie Networks for details.
SFP28 Port
Supported

Hardware Installation and Reference Guide Product Overview
- 4 -
QSFP28 Port
Supported
FC Port
Unsupported
10GBASE-T Port
Unsupported
Temperature
Warning
Support temperature warning and over-temperature protection.
EMC Standards
GB9254-2008 CLASS A
Safety Standards
GB4943-2011
Working
Temperature
0°C to 45°C (32°F to 113°F)
Storage
Temperature
-40°C to 70°C (-40°F to 158°F)
Working Humidity
10% to 90% RH (non-condensing)
Weight
Net weight: 8 kg (including 4 fan modules and 2 power modules)
Dimensions
(L x W x H)
442 mm x 387 mm x 44 mm, 1RU
RG-S6510-48VS8CQ switch is a class A product. In a domestic environment, this product may cause radio
interference in which case the user may be required to take adequate measures.
The 25G/100G Ethernet port of the RG-S6510-48VS8CQ switch supports DAC. For a detailed model and
specification, refer to Appendix B.
Product Appearance
The hardware of the S6510-48VS8CQ includes the chassis, the power supply system and the heat dissipation system.
The power supply system: Provides two power supply slots, which support 1+1 power supply redundancy. It is
recommended users configure power supply redundancy.
The heat dissipation system: Provides four fan module slots, which support 3+1 fan redundancy. It is
recommended users configure all fans redundancy.
Figure 1-1 Appearance of the RG-S6510-48VS8CQ
Front Panel

Hardware Installation and Reference Guide Product Overview
- 5 -
Figure 1-2 Front Panel of the S6510-48VS8CQ
Notes:
1. Switch status indicator
2. Switch locator indicator
3. SFP28 port
4. SFP28 port status indicator
5. QSFP28 port
6. QSFP28 port status indicator
The S6510-48VS8CQ supports 100G QSFP28 module and 25G SFP28 module.
Back Panel
Figure 1-3 Back Panel of the S6510-48VS8CQ
Notes:
1. Power supply module slot
2. Fan module slot
3. Locator indicator
4. MGMT port
5. USB 2.0 port
6. Grounding point
7. Asset label
8. Switch status indicator
9. Console port
Asset Management Label
The asset management label is next to the switch status indicator of the switch back panel. The label is movable and
can be withdrawn from the device. Users can mark the information such as asset name, category, code and registration
date on the label which helps to improve asset management accuracy and efficiency.
Figure 1-4 Asset Management Label of the RG-S6510-48VS8CQ

Hardware Installation and Reference Guide Product Overview
- 6 -
External Ports
The RG-S6510-48VS8CQ provides the following ports:
Universal serial bus (USB) port: This port can connect with USB memory to save logs, host versions, warnings
and other diagnostic messages. Therefore, it is more convenient to upgrade the software version of the switch on
line and save the log information.
To protect the data and avoid device damage, use qualified USB flash disks of good brands. At the same time, the
local USB port is compatible with most of the USB controllers except some USB flash disks.
RG-S6510-48VS8CQ series switches support debugging, configuration, maintenance, management and host
software uploading of Console ports.
Console port: Use RS-232 interface electrical level and standard RJ45 connector. This interface is connected with
the serial port of terminal PC to perform system debugging, configuration, maintenance, management, and host
software uploading.
MGMT port: This is an out-band Ethernet port, which uses standard RJ45 connector. This interface is connected
with Ethernet port of a PC to perform program downloading.
SFP28 port: There are 48 25G SFP28 ports, which support optical modules and DAC copper cables (10GBASE-X
compatible).
QSFP28 port: There are 8 100G QSFP28 ports, which support optical modules and DAC copper cables. These
ports can also work in 4x25G mode.
Indicator
Indicator
Panel
Identification
Status
Meaning
Switch status indicator
(Front panel/Back
panel)
Status
Off
The system is not powered up.
Solid red
1) One of the modules of the system fails.
2) There are less than 3 fans.
3) The internal or partial temperature exceeds the
warning working temperature, and the switching
service resets.
Blinking green.
The system is initializing.
Solid green
The system is operational.

Hardware Installation and Reference Guide Product Overview
- 7 -
Solid yellow
1) The temperature gets to the warning threshold.
2) Only 3 fans are in the position.
3) One of the dual powers is not connected with the
AC power cord.
Switch locator indicator
(Front panel/Back
panel)
ID
Off
Device location is disabled.
Solid blue
Device location is enabled.
MGMT port indicator
MGMT
Off
The port is not connected.
Green
The port is connected at 10M/100M/1000Mbps.
Blinking
The port is transmitting or receiving data.
SFP28 port status
indicator
1F-48F
Off
The port is not connected.
Solid green
The port is connected at 10G/25Gbps.
Blinking green
The port is transmitting or receiving data at
10G/25Gbps.
QSFP28 port status
indicator
49F-56F
Off
The port is not connected.
Solid green
The port is connected at 40G/100Gbps.
Blinking green
The port is transmitting or receiving data at
40G/100Gbps.
Power Supply
The RG-S6510-48VS8CQ series switches support power supply the RG-PA550I-F and RG-PA550I-R. The smart power
supply module supports power management, and the host can read input power, input current, and temperature in real
time. The power supply module supports hot swapping.
The RG-S6510-48VS8CQ series switches support 1+1 power supply redundancy. To improve the stability and
reliability of the entire system, it is recommended to configure 1+1 power supply redundancy.When the two power
supply modules work normally, the switch is in the status of current sharing.
It requires at least one power supply module to work normally. Filler panels need to be installed in the unoccupied
power supply module slots to ensure ventilation and heat dissipation and avoid dusts.
Heat Dissipation
The working temperature of the RG-S6510-48VS8CQ switches is 0°C to 45°C, or 32°F to 113°F, and the heat
dissipation design needs to ensure the stability, safety and maintainability in such environment. The
RG-S6510-48VS8CQ series switches adopt fan ventilation and forced convection to ensure the device can work
normally in specified environment. Dust the device every three months to avoid blocking the ventilation openings.
The RG-S6510-48VS8CQ supports M6510-FAN-F and M6510-FAN-R and provides fan speed regulation, fan failure
warning, and fan hot swapping.
Figure 1-5 Ventilation and Heat Dissipation of the RG-S6510-48VS8CQ

Hardware Installation and Reference Guide Product Overview
- 8 -
Figure 1-6 Ventilation and Heat Dissipation of the RG-S6510-48VS8CQ
Leave sufficient space in the front and at the back of the chassis (at least 20 cm) for ventilation.
It requires at least three fan modules to work normally. Filler panels need to be installed in the unoccupied fan
module slots to ensure ventilation and heat dissipation and avoid dusts.
Power modules and fan modules with different air direction cannot be used together.