Ruijie RG-S6110 Series Installation and operating manual

RG-S6110 Series Switches
Hardware Installation and Reference Guide V1.0

Copyright Statement
Ruijie Networks©2019
Ruijie Networks reserves all copyrights of this document. Any reproduction, excerption, backup, modification,
transmission, translation or commercial use of this document or any portion of this document, in any form or by anymeans,
without the prior written consent of Ruijie Networks is prohibited.
Exemption Statement
This document is provided “as is”. The contents of this document are subject to change without any notice. Please obtain
the latest information through the Ruijie Networks website. Ruijie Networks endeavors to ensure content accuracy and will
not shoulder any responsibility for losses and damages caused due to content omissions, inaccuracies or errors.

Preface
Thank you for using our products. This manual will guide you through the installation of the device.
This manual describes the functional and physical features and provides the device installation steps, hardware
troubleshooting, module technical specifications, and specifications and usage guidelines for cables and connectors.
Audience
It is intended for the users who have some experience in installing and maintaining network hardware. At the same time, it
is assumed that the users are already familiar with the related terms and concepts.
Obtaining Technical Assistance
Ruijie Networks Website: https://www.ruijienetworks.com/
Technical Support Website: https://ruijienetworks.com/support
Case Portal: https://caseportal.ruijienetworks.com
Community: https://community.ruijienetworks.com
Technical Support Email: [e-mail]
Skype: [e-mail]
Related Documents
Documents
Description
Configuration Guide
Describes network protocols and related mechanisms that supported by the
product, with configuration examples.
Command Reference
Describes the related configuration commands, including command modes,
parameter descriptions, usage guides, and related examples.
Symbol Conventions
Means reader take note. Notes contain helpful suggestions or references.
Means reader be careful. In this situation, you might do something that could result in equipment damage or loss of
data.

Hardware Installation and Reference Guide Product Overview
- 1 -
1 Product Overview
The RG-S6110-48XS4QXS series switches are the high-density 10G layer 3 IPv6 cassette switches introduced by
Ruijie Networks. They are mainly applicable to the data center to provide the convergence access for the servers.
An SFP+ port supports both 10Gbase-R and 1000base-X.
A QSFP+ port support both 40G mode and 40 x 10G mode.
1.1 RG-S6110-48XS4QXS
Specifications
Model
RG-S6110-48XS4QXS
CPU
Dual-core CPU, each core with the clock speed of 1.0GHz
Bootrom
8MB
Flash Memory
512MB
SDRAM
2GB
Extension Module
Slot
Unsupported
Extension Module
Unsupported
Fan Slot
4 (support 3+1 redundancy, configure at least three fan modules in one switch)
Fan Module
M6110-FAN-F
Power Supply Slot
2 (support1+1 redundancy)
Power Module
RG-M6110-AC460E-F
Power Supply Input
AC input
Rated voltage range: 100 VAC to 240 VAC
Maximum voltage range: 90 VAC to 264 VAC
Frequency: 50 Hz to 60 Hz
Rated current: 5.29 A
High voltage direct current (HVDC) input:
Input voltage range: 192 VDC to 290 VDC
Input current range: 2.66 A to 2.03 A
Power
Consumption
Less than 250W
Optical Module
Refer to Appendix B
The supported modules update at any time, contact Ruijie Networks for details.
SFP+ Port
Supported
QSFP+ Port
Supported
10Gbase-T Port
Unsupported
EMC
GB9254-2008 CLASSA
EMI
GB4943-2011
Working
Temperature
0°C to 50°C
Storage
Temperature
-40°C to 70°C

Hardware Installation and Reference Guide Product Overview
- 2 -
Working Humidity
10% to 90% RH(non-condensing)
Weight
Net weight 9KG (including four fan modules and two power modules)
Dimensions
440 x 420 x 44 (L xW x H, mm),1RU
RG-S6110-48XS4QXS switch is a class A product. In a domestic environment, this product may cause radio
interference in which case the user may be required to take adequate measures.
The 10G or 40G Ethernet port of the RG-S6110-48XS4QXS switch supports direct attach copper (DAC) cable.
The SFP+ port supports 1-meter, 3-meter and 5-meter cable, and the QSFP+ port supports 3-meter cable. For a
detailed model and specification, refer to Appendix B.
Product Appearance
The hardware of the RG-S6110-48XS4QXS includes the chassis, the power supply system and the heat dissipation
system.
The power supply system: Provides two power supply slots, which support 1+1 power supply redundancy. It is
recommended users configure power supply redundancy.
The heat dissipation system: Provides four power supply slots, which support 3+1 fan redundancy. It is
recommended users configure all fans redundancy.
Figure 1-1 Appearance of the RG-S6110-48XS4QXS
Front Panel
Figure 1-2 Front Panel of the RG-S6110-48XS4QXS

Hardware Installation and Reference Guide Product Overview
- 3 -
Notes:
①Switch status indicator
②PWR1 status indicator
③PWR2 status indicator
④RCMI management interface
indicator
⑤Fan status indicator
⑥10G SFP+ port status indicator
⑦40G QSFP+ port status indicator
⑧10/100/1000Base-T RCMI Ethernet port
⑨Console
⑩10G SFP+ port
⑪40G QSFP+ port
The RG-S6110-48XS4QXS supports 10G SFP+ module and 1G SFP module. But the 10G SFP+ module cannot
function as the 1G SFP module.
Back Panel
Figure 1-3 Back Panel of the S6110-48XS4QXS
Notes:
①Power supply module slot
②Fan module slot
③USB2.0 interface
④Asset management label
⑤Grounding pole
Asset management label
The asset management label is at the lower-right corner of the switch back panel. The label is movable and can be
withdrawn from the device. Users can mark the information such as asset name, category, code and registration date
on the label which helps to improve asset management rate and efficiency.
Figure 1-4 Asset Management Label of the S6110-48XS4QXS
External Interface
The S6110-48XS4QXS provides the following interfaces:
Universal serial bus (USB) port: This port can connect with USB memory to save logs, host versions, warnings
and other diagnostic messages. Therefore, it is more convenient to upgrade the software version of the switch on
line and save the log information.

Hardware Installation and Reference Guide Product Overview
- 4 -
To protect the data and avoid device damage, use qualified USB flash disks of good brands. At the same time, the
local USB interface is compatible with most of the USB controllers except some USB flash disks.
Console port: Use RS-232 interface electrical level and standard RJ45 connector. This interface is connected with
the serial port of terminal PC to perform system debugging, configuration, maintenance, management, and host
software uploading.
10/100/1000M RCMI management port: This is an out-band Ethernet port, which uses standard RJ45 connector.
This interface is connected with Ethernet port of a PC to perform program downloading. Use standard network
cable when the interface is connected with the Ethernet port.
SFP+ port: There are 48 10G QSFP+ ports, which support optical modules and DAC copper cables, and are
compatible with 1000Base-X.
QSFP+ port: There are four 40G QSFP+ ports, which support optical modules and DAC copper cables. This port
can work in 4x10 mode.
Indicator
Indicator
Panel
Identification
Status
Meaning
System indicator
Status
Off
The system is not powered up.
Solid red
1) One of the modules of the system fails.
2) The internal temperature exceeds the warning
working temperature, and the switching service
resets.
Blinking green.
The system is initializing.
Solid green
The system is working normally.
Power module 1
indicator
PWR1
Off
The power supply module is not in the position.
Solid red
The power supply module fails or it is not connected
with theAC power cord.
Solid green
The power supply module works normally.
Power module 2
indicator
PWR2
Off
The power supply module is not in the position.
Solid red
The power supply module fails
Solid green
The power supply module works normally.
RCMI port indicator
RCMI
Off
The port is not linked up.
Green
The port is linked up in 1000M mode.
Yellow
The port is linked up in 10M or 1000M mode.
Blinking
Data are transceiving at the port.
Fan module indicator
Fan
Solid green
All fan modules are in the position and working
normally.
Solid red
1) Afan fails.
2) The number of the fan module is less than three.
SFP+ port status
indicator
1F-48F
(Ethernet
mode)
Off
The port is not linked up.
Solid green
Port 10G/1G is linked up.
Blinking green
Port 10G/1G is transceiving data.
QSFP+ port status
49F-64F
Off
The port is not linked up.

Hardware Installation and Reference Guide Product Overview
- 5 -
indicator
(4 x 10G
mode)
Solid green
Port 10G is linked up.
Blinking green
Port 10G is transceiving data.
65F-68F
(1 x 40G
mode)
Off
The port is not linked up.
Solid green
Port 40G is linked up.
Blinking green.
Port 40G is transceiving data.
Power Supply
The RG-S6110-48XS4QXS series switches support power supply the RG-M6110-AC460E-F. The smart power supply
module supports power management, and the host can read input power, input current, and temperature in real time.
The power supply module supports hot plugging.
The RG-S6110-48XS4QXS series switches support power supply 1+1 redundancy. To improve the stability and
reliability of the entire system, it is recommended to configure power supply module 1+1 redundancy. When the
two power supply modules work normally, the switch is in the status of current sharing.
It requires at least one power supply module to work normally. Baffles need to be installed in the empty power
supply module slots to ensure ventilation and heat dissipation and avoid dusts.
Heat Dissipation
The working temperature of the RG-S6110-48XS4QXS switches is 0-50℃, and the heat dissipation design needs to
ensure the stability, safety and maintainability in such environment. The RG-S6110-48XS4QXS series switches adopt
fan ventilation and forced convection to ensure the device can work normally in specified environment. Dust the device
every three months to avoid blocking the ventilation openings.
The RG-S6110-48XS4QXS supports fan module M6110-FAN-F and provides fan speed regulation, fan failure warning,
and fan hot plugging.
Figure 1-5 Ventilation and Heat Dissipation of the RG-S6110-48XS4QXS
Leave sufficient space in the front and at the back of the chassis (at least 20 cm) for ventilation.
It requires at least three fan modules to work normally. Baffles need to be installed in the empty fan module slots to
ensure ventilation and heat dissipation and avoid dusts.
1.2 Module
The RG-S6110-48XS4QXS series switches adopt modularization design. Strictly complying with the industrial standard,
the system modules are reasonably subdivided and the module interfaces are unified. All these ensure that the
RG-S6110-48XS4QXS series switches system is complete and all modules are independent.

Hardware Installation and Reference Guide Product Overview
- 6 -
The RG-S6110-48XS4QXS series switches support M6110-AC460E-F (power supply module) and M6110-FAN-F (fan
module).
1.2.1 M6110-FAN-F
The M6110-FAN-F is the fan module of the RG-S6110-48XS4QXS series. The M6110-FAN-F provides heat dissipation
system and ensures system satiability. The M6110-FAN-F supports speed regulation and hot plugging.
Module Appearance
Figure 1-6 Appearance of the M6110-FAN-F
Notes:
①Status indicator
Indicator
Indicator
Panel
Identification
Status
Meaning
Status Indicator
Status
Off
The fan is not powered up.
Solid green
The fan is working normally.
Solid red
The fan fails or stops.
Specifications
Fan Model
M6110-FAN-F
Ventilation
Indication
30 CFM
Max Speed
25000 RPM
Power
Consumption
15 W
Weight
Net weight: 0.25 kg
Dimensions
166 x 55.7 x 41.2 (L xW x H, mm)
1.2.2 M6110-AC460E-F
The M6110-AC460E-F is the power supply module of the RG-S6110-48XS4QXS series and provides power supply for
the RG-S6110-48XS4QXS series. The smart power supply module M6110-AC460E-F can access to information such

Hardware Installation and Reference Guide Product Overview
- 7 -
as the power supply status, output power and current, and working temperature at any time. The M6110-AC460E-F
supports both AC input and high voltage direct current (HVDC) input.
External Interface
The front panel of the power supplymodule provides a three-core power port, which can be connected to standard 10 A
power cord.
Indicator
Indicator
Panel
Identification
Status
Meaning
Status Indicator
N/A
Off
No power input or the power supply fails.
Solid green
The power input is normal.
Specifications
Module Model
M6110-AC460E-F (AC input)
M6110-AC460E-F (HVDC input)
Rated Voltage
Range
100 VAC to 240 VAC; 50/60 Hz
N/A
Max Voltage
Range
90-264V~;47-63Hz
192 VDC to 290 VDC;
Max Power
Output
460 W
460 W
Weight
Net weight: 0.9 kg
Dimensions
243.2 x 86.4 x 39.9 (L x W x H, mm)
Power Cord
Requirement
10 A power cord
Make sure the power cord is removed before plugging or unplugging the power supply.