Ruijie RG-NBS3200 Series Installation and operating manual

Ruijie RG-NBS3200 Series Switches
Hardware Installation and Reference Guide

Copyright Statement
Ruijie Networks©2020
Ruijie Networks reserves all copyrights of this document. Any reproduction, excerption, backup, modification,
transmission, translation or commercial use of this document or any portion of this document, in any form or by any means,
without the prior written consent of Ruijie Networks is prohibited.
Exemption Statement
This document is provided “as is”. The contents of this document are subject to change without any notice. Please obtain
the latest information through the Ruijie Networks website. Ruijie Networks endeavors to ensure content accuracy and will
not shoulder any responsibility for losses and damages caused due to content omissions, inaccuracies or errors.

Preface
Thank you for using our products. This manual will guide you through the installation of the device.
This manual describes the functional and physical features and provides the device installation steps, hardware
troubleshooting, module technical specifications, and specifications and usage guidelines for cables and connectors.
Audience
It is intended for the users who have some experience in installing and maintaining network hardware. At the same time, it
is assumed that the users are already familiar with the related terms and concepts.
Obtaining Technical Assistance
Ruijie Networks Website: https://www.ruijienetworks.com/
Technical Support Website: https://ruijienetworks.com/support
Case Portal: https://caseportal.ruijienetworks.com
Community: https://community.ruijienetworks.com
Technical Support Email: [email protected]
Skype: [email protected]
Related Documents
Documents
Description
Configuration Guide
Describes network protocols and related mechanisms that supported by the
product, with configuration examples.
Command Reference
Describes the related configuration commands, including command modes,
parameter descriptions, usage guides, and related examples.
Symbol Conventions
Means reader take note. Notes contain helpful suggestions or references.
Means reader be careful. In this situation, you might do something that could result in equipment damage or loss of
data.

Ruijie RG-NBS3200 Series Switches Hardware Installation and Reference Guide Product Overview
4
1 Product Overview
Ruijie RG-NBS3200 series switches are mainly applicable to the small and medium-sized enterprise (SME) networks to
provide services according to business needs to ensure the prompt transmission of key data. The RG-NBS3200 series
switches provide various interfaces to meet the requirement for interfaces in network constructions.
RG-NBS3200 Series Switches
Model
10/100/1000
Base-T Ethernet Port
1000Base-X SFP
Port
10G SFP+ Port
Console Port
Power
Supply
RG-NBS3200-2
4GT4XS
24
N/A
4
N/A
Single
RG-NBS3200-2
4SFP/8GT4XS
8 (combo)
24
4
N/A
Single
RG-NBS3200-2
4GT4XS-P
24 (Support PoE+)
N/A
4
N/A
Single
RG-NBS3200-4
8GT4XS
48
N/A
4
N/A
Single
RG-NBS3200-4
8GT4XS-P
48 (Support PoE+)
N/A
4
N/A
Single
1000Base-T is downward compatible with 100Base-TX and 10Base-T.
Combo port consists of one 1000Base-X SFP port and one 10/100/1000Base-T Ethernet port. That is, only one
port of them is available at a particular time.
1.1 RG-NBS3200-24GT4XS
Technical Specifications
Model
RG-NBS3200-24GT4XS
CPU
Built-in CPU, single-core processor, 800MHz
BOOTROM
N/A
Flash Memory
256 MB
SDRAM
DDRIII 512MB
Optical Module
See Appendix B.
The copper cable is not supported.
The supported module type may change at any time. Consult Ruijie Networks for the latest
information.
SFP+ Port
10GBase-R
1000Base-X
Power Supply
AC input

Ruijie RG-NBS3200 Series Switches Hardware Installation and Reference Guide Product Overview
5
Rated voltage range: 100V to 240V
Maximum voltage range: 90V to 264V
Frequency: 50/60 Hz
Rated current: 1.5A
Input Leakage
Current
≤3.5mA
EEE
Supported
PoE
Not supported
Power
Consumption
28W
Temperature
Operating temperature: 0 ºC to 50ºC
Storage temperature: -40 ºC to 70ºC
Humidity
Operating humidity: 10% to 90% RH
Storage humidity: 5% to 95% RH
Fan
Supports adaptive speed adjustment
Temperature
Alarm
Not supported
EMC Standards
GB9254-2008
EN 55032:2015+AC:2016
EN 61000-3-2:2014
EN 61000-3-3:2013
EN 55035:2017
ETSI EN 300 386 V2.1.1 (2016-07)
Security
Standards
GB4943-2011
EN 62638-1
Dimensions
(W x D x H)
440 mm x 207.5 mm x 43.6 mm (with front panel )
Weight
2.9 kg
The RG-NBS3200-24GT4XS switch is a class A product. In a domestic environment, this product may cause radio
interference in which case the user may be required to take adequate measures.
Product Appearance
On the front panel, the RG-NBS3200-24GT4XS Ethernet switch provides 24 10/100/1000Base-T Ethernet ports and 4
SFP+ ports. On the back panel, it provides an AC power port.
Figure 1-1 Appearance of RG-NBS3200-24GT4XS

Ruijie RG-NBS3200 Series Switches Hardware Installation and Reference Guide Product Overview
6
Front Panel
Figure 1-2 Front Panel of RG-NBS3200-24GT4XS
Note:
1. Reset button
2. System status LED
3. 10/100/1000 Base-T Ethernet port
4. 10GE SFP+ port
The switch reboots after the reset button is pressed for less than 2 seconds.
The switch restores the default factory settings after the reset button is pressed for more than 5 seconds (until the
status LED blinks).
Back Panel
Figure 1-3 Back Panel of RG-NBS3200-24GT4XS
Note:
1. Power cord retention clips
2. Three-hole AC power receptacle
3. Protective earthing terminal
This device relies on the separate protective earthing terminal.
The device installation shall be permanently connected to building earth by a skilled person.
The device shall be intended to be used in a location having equipotential bonding(such as a telecommunication
centre, a dedicated computer room, or a restricted access area).
Heat Dissipation

Ruijie RG-NBS3200 Series Switches Hardware Installation and Reference Guide Product Overview
7
RG-NBS3200-24GT4XS adopts side-to-rear heat dissipation, thereby ensuring normal function of the device in the
specified environment. 10 cm distance space should be reserved at both sides and the back plane of the cabinet to
allow air circulation. It is recommended to clean the device once every 3 months to avoid dust from blocking vents.
Figure 1-4 Flow Scheme of Heat Dissipation
LED
LED
Panel Identification
State
Meaning
System status LED
Status
Off
The switch is not receiving power.
Blinking green
(0.5Hz)
The switch is running, but is not connected to
Ruijie Cloud.
Blinking green
(10Hz)
The switch is being upgraded or initialized.
Solid green
The switch is connected to Ruijie Cloud.
10/100/1000Base-T
Ethernet port status
LED
1-24
Off
The port is not connected.
Solid green
The port is connected at 10/100/1000 Mbps.
Blinking green
The port is receiving or transmitting traffic.
SFP+ port status
LED
25F-28F
Off
The port is not connected.
Solid green
The port is connected.
Blinking green
The port is receiving or transmitting traffic.
1.2 RG-NBS3200-24SFP/8GT4XS
Technical Specifications
Model
RG-NBS3200-24SFP/8GT4XS
CPU
Built-in CPU, single-core processor, 800MHz
BOOTROM
N/A
Flash Memory
256 MB
SDRAM
DDRIII 512MB

Ruijie RG-NBS3200 Series Switches Hardware Installation and Reference Guide Product Overview
8
Optical Module
See Appendix B.
The copper cable is not supported.
The supported module type may change at any time. Consult Ruijie Networks for the
latest information.
SFP Port
100Base-FX
1000Base-X
SFP+ Port
10GBase-R
1000Base-X
Power Supply
AC input
Rated voltage range: 100V to 240V
Maximum voltage range: 90V to 264V
Frequency: 50/60 Hz
Rated current:2A
Input Leakage
Current
≤3.5mA
EEE
Supported
PoE
Not supported
Power
Consumption
42W
Temperature
Operating temperature: 0 ºC to 50ºC
Storage temperature: -40 ºC to 70ºC
Humidity
Operating humidity: 10% to 90% RH
Storage humidity: 5% to 95% RH
Fan
Supports adaptive speed adjustment
Temperature
Alarm
Not supported
EMC Standards
GB9254-2008
EN 55032:2015+AC:2016
EN 61000-3-2:2014
EN 61000-3-3:2013
EN 55035:2017
ETSI EN 300 386 V2.1.1 (2016-07)
Security
Standards
GB4943-2011
EN 62638-1
Dimensions
(W x D x H)
440 mm x 267.5 mm x 43.6 mm (with front panel )
Weight
3.35 kg
The RG-NBS3200-24SFP/8GT4XS switch is a class A product. In a domestic environment, this product may cause
radio interference in which case the user may be required to take adequate measures.

Ruijie RG-NBS3200 Series Switches Hardware Installation and Reference Guide Product Overview
9
Product Appearance
On the front panel, the RG-NBS3200-24SFP/8GT4XS Ethernet switch provides 24 SFP ports (8 Gigabit combo ports)
and 4 SFP+ ports. On the back panel, it provides an AC power port.
Figure 1-5 Appearance of RG-NBS3200-24SFP/8GT4XS
Front Panel
Figure 1-6 Front Panel of RG-NBS3200-24SFP/8GT4XS
Note:
1. Reset button
2. System status LED
3. 1000Base-X SFP port
4. Combo port
5. 10GE SFP+ port
The switch reboots after the reset button is pressed for less than 2 seconds.
The switch restores the default factory settings after the reset button is pressed for more than 5 seconds (until the
status LED blinks).
Back Panel
Figure 1-7 Back Panel of RG-NBS3200-24SFP/8GT4XS
Note:
1. Power cord retention clips
2. Three-hole AC power receptacle
3. Protective earthing terminal
This device relies on the separate protective earthing terminal.

Ruijie RG-NBS3200 Series Switches Hardware Installation and Reference Guide Product Overview
10
The device installation shall be permanently connected to building earth by a skilled person.
The device shall be intended to be used in a location having equipotential bonding(such as a telecommunication
centre, a dedicated computer room, or a restricted access area).
Heat Dissipation
RG-NBS3200-24SFP/8GT4XS adopts fan for heat dissipation, thereby ensuring normal function of the device in the
specified environment. 10 cm distance space should be reserved at both sides and the back plane of the cabinet to
allow air circulation. It is recommended to clean the device once every 3 months to avoid dust from blocking vents.
Figure 1-8 Flow Scheme of Heat Dissipation
LED
LED
Panel Identification
State
Meaning
System status LED
Status
Off
The switch is not receiving power.
Blinking green
(0.5Hz)
The switch is running, but is not connected to
Ruijie Cloud.
Blinking green
(10Hz)
The switch is being upgraded or initialized.
Solid green
The switch is connected to Ruijie Cloud.
10/100/1000Base-T
Ethernet port status
LED
17-24 (Combo ports)
Off
The port is not connected.
Solid green
The port is connected at 10/100/1000 Mbps.
Blinking green
The port is receiving or transmitting traffic.
SFP port status LED
1F-24F
Off
The port is not connected.
Solid green
The port is connected.
Blinking green
The port is receiving or transmitting traffic.
SFP+ port status
25F-28F
Off
The port is not connected.