Ruijie XS-S1930J Series Installation and operating manual

Ruijie XS-S1930J Series Switches
Hardware Installation and Reference Guide

Copyright Statement
Ruijie Networks©2021
Ruijie Networks reserves all copyrights of this document. Any reproduction, excerption, backup, modification,
transmission, translation or commercial use of this document or any portion of this document, in any form or by any means,
without the prior written consent of Ruijie Networks is prohibited.
Exemption Statement
This document is provided “as is”. The contents of this document are subject to change without any notice. Please obtain
the latest information through the Ruijie Networks website. Ruijie Networks endeavors to ensure content accuracy and will
not shoulder any responsibility for losses and damages caused due to content omissions, inaccuracies or errors.

Preface
Thank you for using our products. This manual will guide you through the installation of the device.
This manual describes the functional and physical features and provides the device installation steps, hardware
troubleshooting, module technical specifications, and specifications and usage guidelines for cables and connectors.
Audience
It is intended for the users who have some experience in installing and maintaining network hardware. At the same time, it
is assumed that the users are already familiar with the related terms and concepts.
Obtaining Technical Assistance
⚫Ruijie Networks Website: https://ruijie.co.jp/
⚫Technical Support Website: https://ruijienetworks.com/support
⚫Case Portal: https://caseportal.ruijienetworks.com
⚫Community: https://community.ruijienetworks.com
⚫Technical Support Email: [email protected]
⚫Skype: [email protected]
Related Documents
Documents
Description
Configuration Guide
Describes network protocols and related mechanisms that
supported by the product, with configuration examples.
Command Reference
Describes the related configuration commands, including
command modes, parameter descriptions, usage guides, and
related examples.
Symbol Conventions
The symbols used in this document are described as below:
This symbol brings your attention to some helpful suggestions and references.
This symbol means that you must be extremely careful not to do some things that may damage the device or cause
data loss

Hardware Installation and Reference Guide
Product Overview
1
1 Product Overview
XS-S1930J series switches process different service flows based on various applications to ensure no latency for key
data transmission, mainly used in medium and small-sized enterprises. XS-S1930J series switches provide flexible media
interfaces to cater to diverse requirements.
Table 1-1 XS-S1930J Switch
Model
10/100/1000
Base-T
Ports
PoE Ports
1000Base-X
SFP Ports
Console
Port
Power Supply
XS-S1930J-48GT4SFP
48
/
4
1
One fixed power supply
XS-S1930J-24GT4SFP/2GT
24
/
4 (2 combo
ports)
1
One fixed power supply
XS-S1930J-18GT2SFP
18
/
2
1
One fixed power supply
XS-S1930J-18GT2SFP-P
18
Ports 1-16,
which support
15 W/30 W.
2
1
One fixed power supply
XS-S1930J-8GT2SFP
8
/
2
1
One fixed power supply
XS-S1930J-8GT2SFP-P
8
Ports 1-8,
which support
15 W/30 W
2
1
One fixed power supply
The 1000Base-T ports are downward compatible with 100Base-T and 10Base-T.
A combo port consists of a 1000Base-X SFP port and a 100/1000Base-T port. The two ports cannot work
simultaneously.
XS-S1930J-48GT4SFP
Technical Specifications
Model
XS-S1930J-48GT4SFP
CPU
Built-in CPU, single-core processor, 700 MHz
BOOTROM
/
Flash Memory
32 MB+32 MB
SDRAM
DDRIII 256 MB
Optical Module and
Cables
For details, see Appendix B. (Copper cables are not supported.)
The supported module type may change at any time. Consult us for the latest information.
Power Supply
◼AC input:
Rated voltage range: 100 to 240 VAC
Maximum voltage range: 90 to 264 VAC
Frequency: 50/60 Hz
Rated current: 0.5 A

Hardware Installation and Reference Guide
Product Overview
2
Input Leakage
Current
≤3.5 mA
EEE
Support
PoE
Not support
Max Power
Consumption
(220 VAC)
40 W
Operating
Temperature
-10°C to 50°C (14°F to 122°F)
Storage
Temperature
-40°C to 70°C (-40°F to 158°F)
Operating Humidity
10% to 90% RH
Storage Humidity
5% to 95% RH
Fan
Fanless
Temperature
Warning
Not support
EMC Standards
EN55032, EN55035, VCCI-A
Security Standards
GB4943-2011, EN62368
Dimensions
(W x D x H)
440 mm x 208 mm x 44 mm (17.32 in. x 8.19 in. x 1.73 in.)
Weight
2.8 kg
The XS-S1930J-48GT4SFP switch is a class A product. In a domestic environment, this product may cause radio
interference in which case the user may be required to take adequate measures.
この装置は、クラスＡ機器です。この装置を住宅環境で使用すると電波妨害を引き起こすことがあります。この場
合には使用者が適切な対策を講ずるよう要求されることがあります。 VCCI-A
Product Appearance
On the front panel, the XS-S1930J-48GT4SFP switch provides 48 10/100/1000Base-T Ethernet ports and 4 SFP ports.
On the back panel, it provides an AC power socket.
Figure 1-1 XS-S1930J-48GT4SFP Appearance

Hardware Installation and Reference Guide
Product Overview
3
Front Panel
Figure 1-2 Front Panel of XS-S1930J-48GT4SFP
Note
1. 10/100/1000Base-T Ethernet port
2. System status LED
3. Power status LED
4. Console port
5. SFP port
Back Panel
Figure 1-3 Back Panel of XS-S1930J-48GT4SFP
Note
1. Grounding pole
2. Power cord retention clip
3. Three-pin AC power socket
Power Supply
⚫AC Input
Rated voltage range: ～100 to 240 VAC, 50/60 Hz
Maximum voltage range: ～90 to 264 VAC, 47 Hz to 63 Hz

Hardware Installation and Reference Guide
Product Overview
4
Frequency: 50/60 Hz
Rated current: 0.5 A
Power cord: 10 A
Heat Dissipation
The XS-S1930J-48GT4SFP is designed to be fanless and provides natural heat dissipation, thereby ensuring normal
function of the device in the specified environment. Maintain a minimum clearance of 10cm around the device to allow air
circulation. It is recommended to clean the device once every 3 months to avoid dust from blocking vents.
LEDs
LED
Panel Identification
State
Meaning
Power status LED
Power
Solid green
The switch is powered on.
Off
The switch is powered off.
System status LED
Status
Off
The switch is powered off.
Blinking green
The switch is being initialized.
Continuous blinking indicates errors.
Solid green
The switch is operational.
1000 Mbps RJ-45
port status LED
1-48
Off
The port is not connected.
Solid green
The port is connected at 1000 Mbps.
Solid yellow
The port is connected at 10/100 Mbps.
Blinking green
The port is receiving or transmitting data at 1000
Mbps.
Blinking yellow
The port is receiving or transmitting data at
10/100 Mbps.
1000 Mbps SFP port
status LED
49-52
Off
The port is not connected.
Solid green
The port is connected at 100/1000 Mbps.
Blinking green
The port is receiving or transmitting data at
100/1000 Mbps.
XS-S1930J-24GT4SFP/2GT
Technical Specifications
Model
XS-S1930J-24GT4SFP/2GT
CPU
Built-in CPU, single-core processor, 500 MHz
BOOTROM
/
Flash Memory
64 MB
SDRAM
DDRIII 256 MB
Optical Modules
and Cables
For details, see Appendix B. (Copper cables are not supported.)
The supported module type may change at any time. Consult us for the latest information.
Power Supply
◼AC input:

Hardware Installation and Reference Guide
Product Overview
5
Rate voltage range: 100 to 240 VAC
Maximum voltage range: 90 to 264 VAC
Frequency: 50/60 Hz
Rated current: 0.5 A
Input Leakage
Current
≤3.5 mA
EEE
Support
PoE
Not support
Max Power
Consumption
(220 VAC)
17 W
Operating
Temperature
-5°C to 55°C (23°F to 131°F)
Storage
Temperature
-40°C to 70°C (-40°F to 158°F)
Operating Humidity
10% to 90% RH
Storage Humidity
5% to 95% RH
Fan
Fanless
Temperature
Warning
Not supported
EMC Standards
EN55032, EN55035, VCCI-A
Security Standards
GB4943-2011, EN62368
Dimensions
(W x D x H)
440 mm x 187 mm x 44 mm (17.32 in. x 7.36 in. x 1.73 in.)
Weight
2.5 kg
The XS-S1930J-24GT4SFP/2GT switch is a class A product. In a domestic environment, this product may cause
radio interference in which case the user may be required to take adequate measures.
この装置は、クラスＡ機器です。この装置を住宅環境で使用すると電波妨害を引き起こすことがあります。この場
合には使用者が適切な対策を講ずるよう要求されることがあります。 VCCI-A
Product Appearance
On the front panel, the XS-S1930J-24GT4SFP/2GT switch provides 24 10/100/1000Base-T Ethernet ports and 4 SFP
ports, including 2 combo ports. On the back panel, it provides an AC power socket.
Figure 1-4 XS-S1930J-24GT4SFP/2GT Appearance

Hardware Installation and Reference Guide
Product Overview
6
Front Panel
Figure 1-5 Front Panel of XS-S1930J-24GT4SFP/2GT
Note
1. System status LED
2. Console port
3. 10/100/1000Base-T Ethernet port
4. 100/1000Base-T combo port
5. SFP port
Ports 25 and 26 are copper ports by default.
Back Panel
Figure 1-6 Back Panel of XS-S1930J-24GT4SFP/2GT
Note
1. Power cord retention clip
2. Three-pin AC power socket
3. Grounding pole
Power Supply
⚫AC Input
Rated voltage range: ～100 to 240 VAC, 50/60 Hz
Maximum voltage range: ～90 to 264 VAC, 47 Hz to 63 Hz

Hardware Installation and Reference Guide
Product Overview
7
Frequency: 50/60 Hz
Rated Current: 0.5 A
Power Cord: 10 A
Heat Dissipation
The XS-S1930J-24GT4SFP/2GT is designed to be fanless and provides natural heat dissipation, thereby ensuring normal
function of the device in the specified environment. Maintain a minimum clearance of 10cm around the device to allow air
circulation. It is recommended to clean the device once every 3 months to avoid dust from blocking vents.
LEDs
LED
Panel Identification
State
Meaning
System status LED
Status
Off
The switch is powered off.
Blinking green
The switch is being initialized.
Continuous blinking indicates errors.
Solid green
The switch is operational.
1000 Mbps RJ-45
port status LED
1-26
Off
The port is not connected.
Solid green
The port is connected at 10/100/1000 Mbps.
Blinking green
The port is receiving or transmitting data at
10/100/1000 Mbps.
1000 Mbps SFP port
status LED
25F-28F
Off
The port is not connected.
Solid green
The port is connected at 100/1000 Mbps.
Blinking green
The port is receiving or transmitting data at
100/1000 Mbps.
XS-S1930J-18GT2SFP
Technical Specifications
Model
XS-S1930J-18GT2SFP
CPU
Built-in CPU, single-core processor, 500 MHz
BOOTROM
/
Flash Memory
64 MB
SDRAM
DDRIII 256 MB
Optical Modules
and Cables
For details, see Appendix B. (Copper cables are not supported.)
The supported module type may change at any time. Consult us for the latest information.
Power Supply
◼AC input:
Rate voltage range: 100 to 240 VAC
Maximum voltage range: 90 to 264 VAC
Frequency: 50/60 Hz
Rated current: 0.5 A
Input Leakage
Current
≤3.5 mA