Ruijie Reyee RG-ES126S-LP V2 User manual

To better use the Ruijie device,
read this manual before installation and usage,
and save the manual for future reference.
User Manual
RG-ES126S-LP V2

1
Package Contents
Item Quantity
RG-ES126S-LP V2 Switch 1
Rubber Pad 4
Mounting Bracket 2
Desiccant Bag 1
Power Cord (1.8 m/5.91 ft) 1
M3 x 6 mm Screw 8
Cable Gland 1
Grounding Cable 1
User Manual 1
Login to the official website of Ruijie Networks (https://www.ruijienetworks.com) and enter
the corresponding product category to find the product and download the related
documentation.
Installation Instructions
The RG-ES126S-LP V2 switch can be installed in a 19-inch EIA cabinet. The installation
steps are as follows:
Step 1 Take out the two L-shaped brackets and eight M3 x 6 mm screws from the packing
materials.
Step 2 Secure a bracket to each side of the switch by using four screws.
Installation
User Manual
Mounting the switch in a 19-inch EIA cabinet

Good Supply
Over Load
PoE LED
FlowControl On
PortIsolation
FlowControl Off
SYS
1 3 5 7 9 11 13 15 17 19 21 23
26
25
2 4 6 8 10 12 14 16 18 20 22 24 26F
26F
Port 1 24 10M/100M Link Act Port25 26 10M/100M
1000M Link Act
Link Act
Port
25 26
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 RG-ES126S-LP V2
① ②③ ④⑤ ⑥ ⑦ ⑧⑨
Good Supply
Over Load
PoE LED
FlowControl On
PortIsolation
FlowControl Off
SYS
1 3 5 7 9 11 13 15 17 19 21 23
26
25
2 4 6 8 10 12 14 16 18 20 22 24 26F
26F
Port 1 24 10M/100M Link Act Port 25 26 10M/100M
1000M Link Act
Link Act
Port
25 26
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 RG-ES126S-LP V2
Power Supply
PC
Printer IP Camera
PoE Powered Device
SFP Optical Transceiver
Grounding Cable
IP TelephoneAP
2
Network Configuration
Connect the switch according to your networking needs. The switch does not need any
configuration after being connected.
LEDs and Ports
1. System Status LED
2. 10/100Base-TX Link/Act LED
3. PoE Status LED
4. 10/100/1000Base-TX Copper Port LED
5. 10/100/1000Base-TX Combo Port LED
6. DIP Switch
7. 10/100Base-TX Self-adaptive Ethernet Port
8. 10/100/1000Base-TX Self-adaptive Ethernet Port
9. 100/1000Base-X Combo Port

3
Standard & Protocol
IEEE802.3i, IEEE802.3u, IEEE802.3x, IEEE802.3az, IEEE802.3at,
IEEE802.3af
Port
24 10/100 Mbps Self-adaptive Ethernet Ports (Auto MDI/MDIX)
One 10/100/1000 Mbps Self-adaptive Ethernet Port (Auto MDI/MDIX)
One 10/100/1000 Mbps combo port
Ports 1-24 support PoE power supply
PoE IEEE802.af-compliant and 802.3at-compliant
Maximum PoE output power: 180 W
Maximum PoE output power per port: 30 W
Switching Capacity
8.8 Gbps
Maximum
Power
Consumption
Operating Temperature
0°C to 45°C (32°F to 113°F)
Storage Temperature
4- -0ºC to 70ºC ( 40°F to 158°F)
Operating Humidity
10% to 90% RH (non-condensing)
Storage Humidity
5% to 90% RH (non-condensing)
Working Mode
Standard mode: Flow control is enabled and all ports can communicate
with each other.
Flow Control Off mode: Flow control is disabled and all ports can
communicate with each other.
VLAN mode: Ports 1 to 24 cannot communicate with each other but they
can communicate with ports 25 and 26.
Dimensions (W × D × H)
440 mm x 208 mm x 44 mm (17.32 in. x 8.19 in. x 1.73 in.)
CE Mark warning
The device may cause radio interference in the living environment.
Specifications