Ruijie RG-S29 Series Installation manual

RG-S29 Series Switch
RGOS Command Reference, Release 11.4(1)B12

·
Copyright Statement
Ruijie Networks©2018
Ruijie Networks reserves all copyrights of this document. Any reproduction, excerption, backup, modification,
transmission, translation or commercial use of this document or any portion of this document, in any form or by any means,
without the prior written consent of Ruijie Networks is prohibited.
Exemption Statement
This document is provided “as is”. The contents of this document are subject to change without any notice. Please obtain
the latest information through the Ruijie Networks website. Ruijie Networks endeavors to ensure content accuracy and will
not shoulder any responsibility for losses and damages caused due to content omissions, inaccuracies or errors.

·
Preface
Thank you for using our products. This manual matches the RGOS Release 11.4(1)B12.
Audience
This manual is intended for:
Network engineers
Technical support and servicing engineers
Network administrators
Obtaining Technical Assistance
Ruijie Networks Website: https://www.ruijienetworks.com/
Technical Support Website: https://ruijienetworks.com/support
Case Portal: http://caseportal.ruijienetworks.com
Community: http://community.ruijienetworks.com
Technical Support Email: s[email protected]
Skype: [email protected]
Related Documents
Documents
Description
Configuration Guide
Describes network protocols and related mechanisms that supported by the
product, with configuration examples.
Hardware Installation and Reference
Guide
Describes the functional and physical features and provides the device
installation steps, hardware troubleshooting, module technical specifications,
and specifications and usage guidelines for cables and connectors.
Conventions
This manual uses the following conventions:
Convention
Description
boldface font
Commands, command options, and keywords are in boldface.
italic font
Arguments for which you supply values are in italics.
[ ]
Elements in square brackets are optional.
{ x | y | z }
Alternative keywords are grouped in braces and separated by vertical bars.

·
[ x | y | z ]
Optional alternative keywords are grouped in brackets and separated by
vertical bars.
Symbols
Means reader take note. Notes contain helpful suggestions or references.
Means reader be careful. In this situation, you might do something that could result in equipment damage or loss of
data.

System Configuration Commands
1. Command Line Interface Commands
2. Basic Configuration Management Commands
3. Line Commands
4. File System Commands
5. SYS Commands
6. Time Range Commands
7. HTTP Service Commands
8. Syslog Commands
9. CWMP Commands
10.CA-MONITOR Commands
11.ZAM Commands
12.Module Hot-plugging/Unplugging Commands
13.Supervisor Module Redundancy Commands
14.PoE Management Commands
15.PKG-MGMT Command

Command Reference Command Line Interface Commands
1 Command Line Interface Commands
1.1 alias
Use this command to configure a command alias in global configuration mode. Use the no or default
form of this command to restore the default setting.
alias mode command-alias original-command
no alias mode command-alias
default alias mode [command-alias]
Parameter
Description
Parameter
Description
mode
Mode of the command represented by the alias
command-alias
Command alias
original-command
Syntax of the command represented by the alias
Defaults
Some commands in user or privileged EXEC mode have default alias.
Command
Mode
Global configuration mode.
Usage Guide
The following table lists the default alias of the commands in privileged EXEC mode.
Alias
Actual Command
h
help
p
ping
s
show
u
undebug
un
undebug
The default alias cannot be removed by the no alias exec command.
After configuring the alias, you can use a word to replace a command. For example, you can create
an alias to represent the first part of a command, and then type the rest part of the command.
The mode of the command represented by the alias is the command mode existing in the current
system. In the global configuration mode, you can use the alias ? command to list all the modes
under which you can configure alias for commands.
Ruijie(config)# alias ?
aaa-gs AAA server group mode
acl acl configure mode
config globle configure mode
......

Command Reference Command Line Interface Commands
The alias also has its help information that is displayed after * in the following format:
*command-alias=original-command
For example, in the privileged EXEC mode, the default alias s stands for show. You can enter s? to
query the key words beginning with s and the help information of the alias.
Ruijie#s?
*s=show show start-chat start-terminal-service
If an alias represents more than one word, the command will be displayed in brackets. For example, if
you set sv stand for show version in the privileged EXEC mode, then:
Ruijie#s?
*s=show *sv="show version" show start-chat
start-terminal-service
The alias must begin with the first letter of the command. The first letter of the command cannot be a
space. The space before the command cannot be used as a valid alias.
Ruijie# s?
show start-chat start-terminal-service
The command alias also has its help information. For example, if the alias ia represents ip address in
the interface configuration mode, then:
Ruijie(config-if)#ia ?
A.B.C.D IP address
dhcp IP Address via DHCP
Ruijie(config-if)# ip address
The above help information lists the parameters of ip address and shows the actual command name.
You must enter an entire alias; otherwise it cannot be recognized.
Use the show aliases command to show the aliases setting in the system.
Configuration
Examples
The following example uses def-route to represent the default route setting of ip route 0.0.0.0 0.0.0.0
192.168.1.1 in the global configuration mode:
Ruijie# configure terminal
Ruijie(config)# alias config def-route ip route 0.0.0.0 0.0.0.0 192.168.1.1
Ruijie(config)#def-route?
*def-route="ip route 0.0.0.0 0.0.0.0 192.168.1.1"
Ruijie(config)# end
Ruijie# show aliases config
globle configure mode alias:
def-route ip route 0.0.0.0 0.0.0.0
192.168.1.1
Related
Commands
Command
Description
show aliases
Displays the aliases settings.
Platform
Description
N/A

Command Reference Command Line Interface Commands
1.2 privilege
Use this command to attribute the execution rights of a command to a command level in global
configuration mode. Use the no form of this command to restore the default setting.
privilege mode [ all ] [ level level | reset ]command-string
no privilege mode [ all ] [ level level ]command-string
Parameter
Description
Parameter
Description
mode
CLI mode of the command to which the execution rights are
attributed.
all
Command alias
level level
Specifies the execution right levels (0–15) of a command or
sub-commands
reset
Restores the command execution rights to its default level
command-string:
Command string to be authorized
Defaults
N/A
Command
Mode
Global configuration mode.
Usage Guide
The following table lists some key words that can be authorized by the privilege command in CLI
mode. The number of command modes that can be authorized may vary with different devices. In the
global configuration mode, you can use the privilege ? command to list all CLI command modes that
can be authorized.
Mode
Descripton
config
Global configuration mode.
exec
Privileged EXEC mode
interface
Interface configuration mode
ip-dhcp-pool
DHCP address pool configuration mode
ip-dhcp-pool
DHCP address pool configuration mode
keychain
KeyChain configuration mode
keychain-key
KeyChain-key configuration mode
Configuration
Examples
The following example sets the password of CLI level 1 as test and attribute the reload rights to reset
the device:
Ruijie(config)#privilege exec level 1 reload
You can access the CLI window as level-1 user to usef the reload command:
Ruijie>reload ?
LINE Reason for reload
<cr> You can use the key word all to attribute all sub-commands of reload to level-1 users:
Ruijie(config)# privilege exec all level 1 reload

Command Reference Command Line Interface Commands
After the above setting, you can access the CLI window as level-1 user to use all sub commands of the
reload command:
Ruijie>reload ?
LINE Reason for reload
at reload at a specific time/date
cancel cancel pending reload scheme
in reload after a time interval
<cr>
Related
Commands
Command
Description
enable secret
Sets the CLI-level password.
Platform
Description
N/A.
1.3 show aliases
Use this command to show all the command aliases or aliases in special command modes.
show aliases [ mode ]
Parameter
Description
Parameter
Description
mode
Mode of the command represented by the alias.
Defaults
N/A.
Command
Mode
Privileged EXEC mode.
Usage Guide
This command displays the configuration of all aliases if no command mode is input.
Configuration
Examples
The following example displays the command alias in privileged EXEC mode:
Ruijie#show aliases exec
exec mode alias:
h help
p ping
s show
u undebug
un undebug
Related
Commands
Command
Description
alias
Sets a command alias.

Command Reference Command Line Interface Commands
Platform
Description
N/A.