Ruijie RG-AP630 Directional Installation and operating manual

RG-AP630 Series Access Point
Hardware Installation and Reference Guide V1.2

Copyright statement
Ruijie Networks©2015
Ruijie Networks reserves all copyrights of this document. Any reproduction, excerption, backup,
modification, transmission, translation or commercial use of this document or any portion of this document,
in any form or by any means, without the prior written consent of Ruijie Networks is prohibited.
, , , ,
,,
,, ,
, , are registered trademarks of Ruijie
Networks. Counterfeit is strictly prohibited.
Exemption statement
This document is provided “as is”. The contents of this document are subject to change without any notice.
Please obtain the latest information through the Ruijie Networks website. Ruijie Networks endeavors to
ensure content accuracy and will not shoulder any responsibility for losses and damages caused due to
content omissions, inaccuracies or errors.

Preface
Thank you for using our products. This manual will guide you through the installation of the access point.
Scope
It is intended for the users who have some experience in installing and maintaining network hardware. At the same time, it
is assumed that the users are already familiar with the related terms and concepts.
Obtaining Technical Assistance
Ruijie Networks website: http://www.ruijienetworks.com
Ruijie service portal: http://case.ruijienetworks.com
Related Documents
Documents Description
Configuration Guide Describes network protocols and related mechanisms that supported by the
product, with configuration examples.
Command Reference Describes the related configuration commands, including command modes,
parameter descriptions, usage guides, and related examples.
Documentation Conventions
The symbols used in this document are described as below:
is symbol bTh rings your attention to some helpful suggestions and references.
This symbol means that you must be extremely careful not to do some things that may damage the device or
cause data loss.

Chapter 1 Product Overview
RG-AP630 is a wireless access point (AP) designed by Ruijie for next-generation high-speed wireless LAN. Adhering to
the latest 802.11ac standard, the AP delivers an access rate of up to 1.75Gbps. It features security, radio frequency (RF)
control, mobile access, Quality of Service (QoS), and seamless roaming, and can be managed by RG-WS series wireless
access controllers (ACs) to implement wireless data forwarding, security, and access control.
The IP67 design adapts Ruijie to inclement outdoor environment, for instance, chillness in northern China and humidity in
southern China. This extremely simplifies installation and maintenance. And the built-in directional and omni-directional
Ruijie patent X-sense smart antennas offer flexible antenna switch and full coverage for various outdoor circumstances.
Moreover, the multi-hop and point-to-multi-points bridging enhances the deployment. The AP fed by IEEE
802.3at-compliant PoE accommodates various monitors and receives real-time monitoring information. It is greatly ideal
for campuses, branch offices, ports, transportation, public security, city blocks, complexes, storage and logistics, tourist
attractions, and other sites.
Technical Specifications
Table 1-1 Technical Specifications of RG-AP630
Model RG-AP630 (Directional) RG-AP630 (Omni-directional)
Dimensions
(L×W×H) 276 mm × 246 mm × 90 mm
Maximum Transmit
Rate 1.75Gbps
Operating
Frequency
802.11b/g/n: 2.4 to 2.483GHz
802.11ac/a/n: 5.15 to 5.85GHz
Maximum Transmit
Power 27dBm
Antenna Type Integrated directional antenna Integrated omni-directional antenna
Antenna Gain 2.4GHz: 10dBi
5GHz: 10dBi
2.4GHz: 4dBi
5GHz: 4dBi
Lobe Width 2.4G: E:45°: H:60°
5G: E:25°: H:60°N/A
Interfaces
One 10/100/1000 Base-T uplink Ethernet port
One SFP uplink port (combo)
One 10/100/1000 Base-T downlink PoE port
Fat/Fit Mode
Switching Supported
LED System status LED
WDS RSSI LED
PoE IEEE 802.3af/at compatible PoE
PSE-capable
Power Consumption <25w

Temperature Operating: -40 to 60℃(-40 to 140℉)
Storage: -40 to 85℃(-40 to 185℉)
Humidity Operating: 0% to 100% (non-condensing)
Storage: 0% to 100% (non-condensing)
IP Rating IP67
Weight <2.5kg
Safety Standards GB4943, EN60601-1-2 (medical care), UL/CSA 60950-1, EN/IEC 60950-1, EN/IEC 60950-22
EMC Standards GB9254-2008, EN301 489, EN55022, FCC Part15, RSS-210
Table 1-2 LEDs of RG-AP630
LED State Meaning
Blinking green Initialization in progress
Solid red & green Initialization is complete, but no CAPWAP connection.
Solid green Initialization is complete, and the AP is establishing a CAPWAP connection
with an AC.
System status
Solid red Warnings
1 solid on < -70dBm
2 solid on -70 to -50dBm
WDS RSSI (3
LEDs in total) 3 solid on > -50dBm
Product Appearance
The AP provides 1 ETH1/PoE IN port (RJ45), 1 ETH2/PoE OUT port (RJ45), 1 SFP compo port, 1 Console port, and 6
N-type antenna connectors.
Figure 1-1 Product Appearance of RG-AP630

Front View
Figure 1-2 Front View of RG-AP630
Note:
1. 2.4GHz antenna connector
3.10/100/1000 Base-T auto-sensing Ethernet/PoE
OUT port
5. SFP combo port
2. Console port
4.10/100/1000 Base-T auto-sensing
Ethernet/PoE IN port
6. 5GHz antenna connector
Power Supply
The AP supports 802.3af/at compatible PoE.

Chapter 2 Preparing for Installation
e safety recommendations described inTo prevent device damage and bodily injury, please read carefully th
this chapter.
The recommendations do not cover all possible hazardous situations.
Grounding and Lightning Protection
Use galvanized steel flat bar (or copper) as horizontal grounding conductor. The steel size should be less than 40
mm x 40 mm. Use galvanized angle steel as vertical grounding conductor. The steel length should be 2.5 m and the
be
n dimensions less than 300 mm2 as the main vertical ground wire for tall buildings.
rk cable through the steel pipe and ground the pipe at both ends.

ening protection, install the lightening
arrester with the grounding cable connected. .
an 5 ohms. In an area with a higher soil resistivity, reduce the soil resistance
vity.
Preparing Installation Site
Do not subject the AP to unstable voltage, vibration, and noises.
size should be less than 50 mm x 50 mm x 5 mm. The steel pipe wall thickness should be less than 3.5 mm.
Use galvanized steel flat as a grounding wire. The length of the wire should be less than 30 m and the size should
40 mm x 4 mm or 50 mm x 5 mm.
Use copper bars with cross-section dimensions less than 160 mm2as ground bus bars. Use copper bars with
cross-sectio
If the distance between the ground bus bar at each floor and the LEB is short, use stranded copper wires with
cross-section dimensions of 16 mm2; if the distance is long, the cross-section dimensions should be greater than 35
mm2.
Use a shielded network cable and make sure that the devices at the two ends of the cable, and the shielded sleeves
are well grounded. Alternatively, run the netwo
A high performance lightning arrester is integrated into the AP with 6KV lightening protection. In general, no
additional lightening arrester is required. If there is higher requirement for light
The ground resistance should be less th
by spreading ground resistance reducer powder to reduce the soil resisti
Do not expose the AP to high temperature, dusts, or harmful gases.
Do not install the AP in an inflammable or explosive environment.
Keep the AP away from EMI sources such as large radar stations, radio stations, and substations.

Keep the AP at least 500 meters away from the seaside and do not face it toward the wind from the sea.
The installation site should be free from water flooding, seepage, dripping, or condensation.
cted according to network planning and features of communications equipment,
tric power, and transportation.
T um
T peratu ies
The installation site should be sele
and considerations such as climate, hydrology, geology, earthquake, elec
emperature and H idity
able 2-1 Required Tem re and Humidity for the RG-AP630 Ser
Operating Temperature -40 to 65 ℃(-40 to 149 °F)
0% to 100% (non-condensing)
Operating Humidity
Outdoor Installation
d on a wall or pole.The AP can be installed outdoors. It can be mounte
Waterproof
Use a seal plug to seal the unused ports.
Figure 2-1 Seal Plug
For details, see Chapter 3 “Installing the Access Point”.Use water-tight adapter to connect cables to the AP.
Figure 2-2 Water-tight Adapter

EMI
All interference sources, either from outside or inside of the device or application system, affect the device by capacitive
coupling, inductive coupling, or electromagnetic waves.
Electromagnetic interference (EMI) occurs due to electromagnetic radiation or conduction, depending on the transmission
path.
Radiation interference occurs when energy, usually radio frequency energy, is emitted from a device and propagated
through space that disturbs other victims. The interference source can be part of disturbed system or a fully electrically
isolated unit. Conduction interference occurs when interference is transferred from one unit to another unit through cables,
which are usually electromagnetic wires or signal cables connected between the source and the victim. Conduction
interference often affects the power supply of the device, and can be eliminated by using filters. Radiation interference can
influence the path of any signal from the device, which is hard to be shielded.
Take effective measures against interference from the power grid.
Keep the AP far away from the grounding or lightning protection devices of power equipment.
Keep the AP away from high-power radio stations, radar stations, and high-frequency high-current devices.
Take electrostatic shielding measures.
Fiber Connection
Before connecting fiber cables, make sure the model of the optical transceiver and fiber type match the optical port. The
transmit port on the local device should be connected to the receive port on the peer device and vice versa.
Installation Tools
Table 2-2 Installation Tools
Tools
Marker, Phillips screwdriver, slotted screwdriver, drill, paper knife, crimping pliers, diagonal
pliers, wire stripper, network cable tester, related power and fiber cables, wrench, hammer,
cable ties, ESD tools, multimeter
The tool kit is customer supplied.
Checking before Installation
Please check your goods carefully against the packing list. If there are any errors, please contact your distributor.

Chapter 3 Installing the Access Point
re you have carefully read the requirements described in Chapter 2.Before installing the AP, make su
Installation Flowchart
Start
Check
Adjust Antenna Orientation
Install External Antenna(Optional)
Install Security Lock (Optional)
Connect Cables
Choose the Site
Install the Bracket on a Wall Install the Bracket on a Pole
Install the AP
End