Ruijie RG-AM5532 Installation and operating manual

Ruijie RG-AM5532 Access Point
Hardware Installation and Reference Guide
Document Version: V1.04
Date: August 16, 2023
Copyright © 2023 Ruijie
Networks

Copyright
Copyright © 2023 Ruijie Networks
All rights are reserved in this document and this statement.
Any reproduction, excerption, backup, modification, transmission, translation or commercial
use of this document or any portion of this document, in any form or by any means, without
the prior written consent of Ruijie Networks is prohibited.
Trademark and are owned by Ruijie
Networks.
All other trademarks or registered trademarks mentioned in this document are owned by
their respective owners.
Disclaimer
The products, services, or features you purchase are subject to commercial contracts and
terms. Some or all of the products, services or features described in this document may not
be within the scope of your purchase or use. Unless otherwise agreed in the contract, Ruijie
Networks does not make any express or implied statement or guarantee for the content of
this document.
Due to product version upgrades or other reasons, the content of this document will be
updated from time to time. Ruijie Networks reserves the right to modify the content of the
document without any notice or prompt.
This manual is for reference only. Ruijie Networks endeavors to ensure content accuracy and
will not shoulder any responsibility for losses and damages caused due to content omissions,
inaccuracies or errors.

I
Preface
Intended Audience
This document is intended for:
Network engineers
Technical support and servicing engineers
Network administrators
Technical Support
Ruijie Networks Website: https://www.ruijienetworks.com/
Technical Support Website: https://ruijienetworks.com/support
Case Portal: https://caseportal.ruijienetworks.com
Community: https://community.ruijienetworks.com
Technical Support Email: [e-mail]
Live Chat: https://www.ruijienetworks.com/rita
Conventions
1.
Signs
The signs used in this document are described as follows:
Warning
An alert that calls attention to important rules and information that if not understood or
followed can result in data loss or equipment damage.
Caution
An alert that calls attention to essential information that if not understood or followed can
result in function failure or performance degradation.
Note
An alert that contains additional or supplementary information that if not understood or
followed will not lead to serious consequences.
Specification
An alert that contains a description of product or version support.

II
2.
Note
The manual offers configuration information (including model, port type and command line
interface) for indicative purpose only. In case of any discrepancy or inconsistency between
the manual and the actual version, the actual version prevails.

Hardware Installation and Reference Guide Product Introduction
3
1
Product Introduction
1.1 Product Overview
Following on from the RG-AM5528 and RG-AM5528(ES), RG-AM5532 is an i-Share+ dedicated
wireless access point (AP) released by Ruijie Networks for scenarios with high building
density, such as the campus network for dormitory buildings and the hospital network for
medical wards. The RG-AM5532 provides four optical ports, four copper ports, or two optical
ports and two copper ports for data uplinks. Four uplink copper ports can supply power to
four devices that support IEEE 802.3af or two devices that support IEEE 802.3at for expansion
of APs that support standard PoE. Based on the IEEE 802.11 protocol, the RG-AM5532 can
provide 24 RF modules by using Category-5 cables to deliver dual-band and two spatial-
stream performance for 24 rooms, with 600 Mbps bandwidth for each room. A total of 14.4
Gbps wireless throughput can be achieved, meeting the high-performance access
requirements in dormitory buildings. Important factors such as the wireless network
security, radio control, mobile access, Quality of Service (QoS), and seamless roaming are
fully taken into account for the RG-AM5532. Therefore, the RG-AM5532 can implement STA
data forwarding, security, and access control.
1.2 AP Specifications
1.2.1 RG-AM5532
Specifications
Product Model
RG-AM5532
Supported Optical
Module Type
For details, see Appendix B.
The module types may update without prior notification. Please
contact Ruijie Networks for details.
1000 Mbps Uplink
Copper Port
1000Base-T
SFP+ Port
10GBase-R or 1000Base-X

Hardware Installation and Reference Guide Product Introduction
4
Power Supply
Rated voltage range: 100 V AC to 240 V AC
Maximum voltage range: 90 V AC to 264 V AC
Frequency: 50/60 Hz
Rated current: 3 A
EEE Function
Supported
PoE Function
Supported. Four uplink copper ports can supply power to four
devices that support IEEE 802.3af or two devices that support IEEE
802.3at. When two uplink ports are used to supply power to two
devices that support IEEE 802.3at, the other two ports cannot be
used to supply power.
Overall Power
Consumption
Less than 300 W with full load
Operating
Temperature
0ºC to 45ºC (32°F to 113°F)
Storage
Temperature
–40°C to +70°C (–40°F to +158°F)
Operating
Humidity
5% to 95% RH
Storage Humidity
5% to 95% RH
Fans
Dual-fan design
Regulatory
compliance
EN 55032, EN 55035, EN 61000-3-3, EN IEC 61000-3-2, ETSI EN 300
386, IEC 62368-1, and EN 62368-1
Dimensions (W ×
D × H)
440 mm × 360 mm × 44 mm (17.32 in. x 14.17 in. x 1.73 in.)
Weight
5.8 kg (12.79 lbs, including the package)

Hardware Installation and Reference Guide Product Introduction
5
Caution
This is a Class A product. In a domestic environment, this product may cause radio
interference. In this case, users are advised to take proper measures against the
interference.
The following symbol on the product nameplate indicates that the RG-AM5532 is applicable
only to areas below 2000 m (6561.68 ft.) above sea level.
Product Appearance
The front panel of the RG-AM5532 provides 24 × 10/100/1000Base-T Ethernet ports, 4 × 1000
Mbps uplink copper ports, 4 × 10 Gbps SFP+ optical ports, and one console port. The rear
panel has an AC power connector.
Figure 1-1 Appearance of the RG-AM5532
Front Panel
Figure 1-2 Front Panel of the RG-AM5532

Hardware Installation and Reference Guide Product Introduction
6
Description 1. RG-AM5532 status LED
2. Power button
3. Console port
4. 10/100/1000Base-T auto-sensing
Ethernet port
5. Copper port status LED
6. 1000Base-T 1000 Mbps uplink
copper port
7. 4 × 10 Gbps SFP+ optical ports
Caution
To change the mode of the port status LED (to switching or PoE mode), you can press and hold the power
button for over two seconds.
Port Modes
Ports 25 to 32 on the RG-AM5532 can work in three modes. Only a maximum of four ports
can work simultaneously in each mode.
(1) Mixed mode: two optical ports and two copper ports. As shown in the following figure,
ports 27, 28, 31, and 32 are working simultaneously.
(2) 4GE mode: four copper ports. As shown in the following figure, ports 25 to 28 are 1000
Mbps uplink copper ports, while ports 29 to 32 are not working.
(3) 4SFP+ mode: four optical ports. As shown in the following figure, ports 29 to 32 are 10
Gbps uplink optical ports, while ports 25 to 28 are not working.
Figure 1-3 Port Modes of the RG-AM5532

Hardware Installation and Reference Guide Product Introduction
7
Rear Panel
Figure 1-4 Rear Panel of the RG-AM5532
Desc
ripti
on
1. Three-pin AC power
connector
2. Grounding stud
Power Supply
The RG-AM5532 adopts AC input and high voltage DC/AC input.
Rated voltage range: 100 V to 240 V
Maximum voltage range: 90 V to 240 V
Frequency: 50/60 Hz
Rated current: 3 A
Power cord requirements: 10 A power cord
Heat Dissipation Solution
The RG-AM5532 adopts the dual-fan design. To ensure proper heat dissipation, maintain a
minimum clearance of 10 cm (3.94 in.) around the device for air circulation. To install the AP
on a rack, it is recommended to install the AP at a spacing of 1 U. Do not stack the AP. Handle
the AP by strictly following the instructions. Avoid blocking the vents; otherwise, the heat
dissipation of the device will be affected. Dust the device every three months to avoid
blocking the ventilation openings.
Figure 1-5 Heat Dissipation of the RG-AM5532

Hardware Installation and Reference Guide Product Introduction
8
LEDs
LED
Identifier
on the
Panel
Status
Description
Status LED Status
Off The RG-AM5532 is not powered on.
Blinking
green
The RG-AM5532 is being initialized.
Continuous blinking indicates a fault.
Steady green The RG-AM5532 is normally running.
Steady red An exception occurs.
1000 Mbps
RJ45 port
LED
(power
supply
mode)
1 to 24
Steady green The port is supplying power to an
external device.
Steady yellow The port is not supplying power to an
external device.
1000 Mbps
RJ45 port
LED
1 to 24
Off No link is detected for this port.
Steady green The port has made a successful 1000
Mbps link.