Ruijie RG-AP130(W2) V2 Series Installation and operating manual

Ruijie RG-AP130(W2) V2 Series Access Points
Hardware Installation and Reference Guide 1.00

·
Copyright statement
Ruijie Networks©2019
Ruijie Networks reserves all copyrights of this document. Any reproduction, excerption, backup,
modification, transmission, translation or commercial use of this document or any portion of this document,
in any form or by any means, without the prior written consent of Ruijie Networks is prohibited.
Exemption statement
This document is provided “as is”. The contents of this document are subject to change without any notice.
Please obtain the latest information through the Ruijie Networks website. Ruijie Networks endeavors to
ensure content accuracy and will not shoulder any responsibility for losses and damages caused due to
content omissions, inaccuracies or errors.

·
Preface
Thank you for using our products. This manual will guide you through the installation of the access point.
Scope
It is intended for the users who have some experience in installing and maintaining network hardware. At the same time, it
is assumed that the users are already familiar with the related terms and concepts.
Obtaining Technical Assistance
Ruijie Networks Website: https://www.ruijienetworks.com/
Technical Support Website: https://ruijienetworks.com/support
Case Portal: https://caseportal.ruijienetworks.com
Community: https://community.ruijienetworks.com
Technical Support Email: [email protected]
Skype: [email protected]
Related Documents
Documents
Description
Configuration Guide
Describes network protocols and related mechanisms that supported by the
product, with configuration examples.
Command Reference
Describes the related configuration commands, including command modes,
parameter descriptions, usage guides, and related examples.
Documentation Conventions
The symbols used in this document are described as below:
This symbol brings your attention to some helpful suggestions and references.
This symbol means that you must be extremely careful not to do some things that may damage the device or cause
data loss.

·
Hardware Installation and Reference Guide Product Overview
1 Product Overview
Ruijie RG-AP130(W2) V2 Wall AP is designed for wireless deployment in hotels, offices, residential buildings and settings
alike.
The dual-radio, dual-band AP supports concurrent operation of 802.11a/n/ac and 802.11b/g/n, delivering data rates of up
to 300Mbps in 802.11n and 866.5Mbps in 802.11ac. The Wall AP provides four 10/100/1000Base-T LAN ports and one
10/100/1000Base-T WAN port, delivering optimal wireless network coverage and cost protection with additional wired
network interfaces and VoIP ports.
RG-AP130(W2) V2 supports security, radio frequency (RF) control, mobile access, Quality of Service (QoS) and
seamless roaming. Teaming up with Ruijie RG-WS Wireless Controller Series, wireless data forwarding, high
performance security and access control can be accomplished with ease.
1.1 Technical Specifications
Table 1-1 Technical Specifications of RG-AP130(W2) V2
Hardware Specifications
Radio
2.4G: 2 x 2MIMO
5G: 2 x 2SU-/MU-MIMO
Transmission
Protocol
2.4G : 802.11b/g/n
5G : 802.11a/n/ac
Operating Bands
802.11b/g/n: 2.4 GHz to 2.4835 GHz
802.11a/n/ac: 5G: 5.15 GHz to 5.35 GHz, 5.47 GHz to 5.725 GHz, 5.725 GHz to 5.850 GHz
(Country-specific)
Antenna
Built-in low-radiation omnidirectional antenna (Base gain 3.5dBi)
Spatial Streams
2 streams
Max Throughput
802.11b/g/n: up to 300Mbps
802.11a/n/ac: up to 867Mbps
Up to 1.167Gbps per AP
Modulation
OFDM: BPSK@6/9Mbps, QPSK @12/18Mbps, 16-QAM@24Mbps, 64-QAM@48/54Mbps
DSSS: DBPSK@1Mbps, DQPSK@2Mbps, and [email protected]/11Mbps
MIMO-OFDM: BPSK, QPSK, 16QAM , 64QAM and 256QAM
Receive Sensitivity
11b/g: -94dBm(1Mbps), -74dBm(54Mbps)
11a: -90dBm(6Mbps), -74dBm( 54Mbps)
11nHT20: -72dBm@MCS7, -68dBm@MCS15
11ac HT20: -90dBm( MCS0) , -65dBm( MCS8)
11ac HT40: -85dBm( MCS0) , -60dBm( MCS9)
11ac HT80: -82dBm( MCS0) , -58dBm( MCS9)
Max Transmit Power
≤100mw (20dBm, RF card transmit power only)
(Depending on the country of use, laws and regulations.)
Transmit Power
Adjustment
1 dBm

·
Hardware Installation and Reference Guide Product Overview
Dimensions
(W x D x H)
116 mm x 86 mm x 39 mm (4.6 in x 3.4 in x 1.5 in)
Weight
0.24 kg
Service Ports
Front:
Four 10/100/1000Base-T LAN ports
Rear:
One 10/100/1000Base-T WAN port
Management Ports
One Micro USB port for console management (hidden)
LED Indicators
Indicator for AP, Ethernet and wireless status
Power Supply
PoE: 802.3af/802.3at
DC: input voltage range: 12 V, rated current: 1 A
Power Consumption
≤8W
Temperature
Operating: 0°C to 45°C (32°F to 113°F)
Storage: -40°C to 70°C (-40°F to 158°F)
Humidity
Operating: 10% to 95% RH (non-condensing)
Storage: 5% to 95% RH (non-condensing)
Installation
Ceiling/wall mount in a 86-type faceplate
IP Rating
IP41
Safety Standards
GB4943
EN/IEC 60950-1
EMC Standards
IEC61373
GB9254
EN301489
EN50121
EN50155
Vibration
China Radio Transmission Equipment Type Approval Certificate
EN300 328
EN301 893
Radio
China Radio Transmission Equipment Type Approval Certificate
EN300 328
EN301 893
MTBF
> 250,000H
1.2 Product Image
The AP provides two built-in radio ports, one 10/100/1000Base-T Ethernet WAN port on the rear panel, and four
10/100/1000Base-T Ethernet LAN ports on the front panel.

·
Hardware Installation and Reference Guide Product Overview
Figure 1-1 Image of RG-AP130(W2) V2
PoE/UpLink port, which is on the rear, is the 10/100/1000Base-T WAN port (PoE-capable).
Four 10/100/1000Base-T LAN ports are on the bottom.
Figure 1-2 Side View of RG-AP130(W2) V2
Note
1. Reset button
2. Micro USB management port (Console)
3. DC power adapter port
4. Screw hole
1.3 LED Indicators

·
Hardware Installation and Reference Guide Product Overview
Figure 1-3 Indicator on the AP
Fit AP Mode:
State
Frequency
Meaning
Off
N/A
The AP is powered off, or the AP is in Silent mode.
Fast blinking
green before
solid green
2.5Hz (fast
blinking green)
Initialization is in progress. The AP is operational.
Fast blinking red
2.5Hz
Firmware upgrade in progress. Do not power off the AP.
Blinking orange
1Hz
AP is operational and Ethernet link is down.
Blinking green
1Hz
AP is operational and Ethernet link is up. CAPWAP error.
Slow blinking
green
0.4Hz
AP is operational and CAPWAP connection is established. At least one client is
associated.
Reset button
Pressed for less
than 2s
Reboots the device.
Pressed for more
than 3s
Restores the default settings.
Fat AP Mode:
State
Frequency
Meaning
Off
N/A
The AP is powered off, or the AP is in Silent mode.
Fast blinking
green before
solid green
2.5Hz (fast
blinking green)
Initialization is in progress. The AP is operational.
Blinking orange
1Hz
AP is operational and Ethernet link is down.
Blinking green
1Hz
AP is operational and Ethernet link is up.
Slow blinking
green
0.4Hz
AP is operational.
Reset button
Pressed for less
than 2s
Reboots the device.
Pressed for more
than 3s
Restores the default settings.
Indicator

·
Hardware Installation and Reference Guide Product Overview
1.4 Power Sources
The AP supports PoE and DC power supply.
PoE power supply
Input voltage range: 44-57V
Rated current: 0.25A
DC power supply
Input voltage range: 12V
Rated current: 1A
When powered through PoE, the AP can be used with Ruijie’s other products supporting 802.3af PoE.
1.5 Cooling Solution
The AP adopts fanless design. Because it is installed in an 86-style faceplate on the wall, to guarantee airflow for proper
ventilation, keep the device uncovered.

·
Hardware Installation and Reference Guide Preparing for Installation
2 Preparing for Installation
2.1 Safety Suggestions
RG-AP130(W2) V2 must be used inside the room. To ensure normal operation and a prolonged useful life of the
equipment, the installation site must meet the following requirements.
To prevent device damage and bodily injury, please read carefully the safety recommendations described in this chapter.
The recommendations do not cover all possible hazardous situations.
2.2 Installation
Do not expose the AP to high temperature, dusts, or harmful gases.
Do not install the AP in an inflammable or explosive environment.
Keep the AP away from EMI sources such as large radar stations, radio stations, and substations.
Do not subject the AP to unstable voltage, vibration, and noises.
Keep the installation site dry. Installing the device near sea is not recommended.
Keep the AP at least 500 meters away from the seaside and do not face it toward the wind from the sea.
The installation site should be free from water flooding, seepage, dripping, or condensation.
The installation site shall be selected according to network planning and features of communications equipment, and
considerations such as climate, hydrology, geology, earthquake, electric power, and transportation.
2.3 Temperature and Humidity
Required temperature and humidity are as follows:
Operating temperature: 0°C to 45°C (32°F to 113°F)
Operating humidity: 10%～95% RH (non-condensing)
2.4 Cleanness
Dust poses a serious threat to device operation. Dust that falls onto the surface of the device can be absorbed onto metal
contact points by static electricity, resulting in poor contact. Electrostatic absorption of dust occurs more easily when the
relative humidity is low, which may shorten the service life of the device and cause communication failures. Table 2-2
shows the maximum concentration and diameter of dust allowed in the equipment room.
Table 2-1
Maximum diameter (μm)
0.5
1
3
5
Maximum concentration
1.4×107
7×107
2.4×107
1.3×107

·
Hardware Installation and Reference Guide Preparing for Installation
(Particles/m3)
Besides, the contents of salts, acids and sulfides in the air are also strictly limited for the equipment room. These
substances can accelerate metal corrosion and the aging of some parts. Table 2-3 describes the limit of some hazardous
gases such as SO2, H2S, NO2and Cl2 in the equipment room.
Table 2-2
Gas
Average (mg/m3)
Maximum (mg/m3)
SO2
0.2
1.5
H2S
0.006
0.03
NO2
0.04
0.15
NH3
0.05
0.15
Cl2
0.01
0.3
2.5 EMI Consideration
Various interference sources, from either outside or inside the equipment or application system, affect the system in the
conductive ways such as capacitive coupling, inductive coupling, and electromagnetic radiation. There are two types of
electromagnetic interferences: radiated interference and conducted interference, depending on the type of the
propagation path. When the energy, often RF energy, from a component arrives at a sensitive component via the space,
the energy is known as radiated interference. The interference source can be both a part of the interfered system and a
completely electrically isolated unit. Conducted interference results from the electromagnetic wire or signal cable
connection between the source and the sensitive component, along the cable the interference conducts from one unit to
another. Conducted interference often affects the power supply of the equipment, but can be controlled by a filter.
Radiated interference may affect any signal path in the equipment, and is difficult to shield.
Effective measures should be taken for the power system to prevent the interference from the electric grid.
The working ground of the routers should be properly separated and kept as far as possible from the grounding
device of the power equipment or the anti-lightning grounding device.
Keep the equipment away from high-power radio transmitter, radar transmitting station, and high-frequency
large-current device.
Measures must be taken to isolate static electricity.
2.6 Installation Tools
Common Tools
Phillips screwdriver, straight screwdriver, related copper and fiber cables, bolts, diagonal pliers,
cable ties
Special Tools
Anti-static tools
Meter
Multimeter
The listed tools, apart from bolts, are customer supplied.