Rutland County Oakham Picnic Bench User manual

Assembly Instructions
Oakham picnic bench
1
Before you commence the assembly process we recommend that you read these instructions
thoroughly beforehand to familiarise yourself with the assembly process and to also check that you have
the correct components. If for any reason you need assistance, you can find our contact details on the
final page of these instructions.
We highly recommend that any assembly is carried out on a flat, level surface if possible and that you
use another person to assist you if necessary.
Package contents
Tools required
1 x Table top
2 x Seats
2 x Table A-frames
2 x Cross braces
16 x M8 Coach screws
Cover caps
10mm socket or spanner
The Oakham picnic bench

Oakham picnic bench
Rutland County Garden Furniture Ltd, Ashbourne House, 2 Dovecote Meadows,
Aslackby, Sleaford, Lincs, NG34 0HZ.
Company No: 7670072 VAT No: 151744027
2
Step 1
Step 2
Ensure that you have all of the correct parts as listed
on the front page of these instructions, including any
fixings.
Lay the table top upside down on a clean, flat surface
taking care not to damage it. Now line up one of the
table A-frames centrally on the table top as shown in
step 3.
Step 3
Step 4
Place one of the table A-frames centrally against the
fixing batten ensuring that the gap at the table edge
is the same on both sides. Now, using 2 of the
supplied coach screws and the pre drilled holes,
secure the table A-frame to the fixing batten on the
table top.
Place a cross brace in position as shown, ensuring
that it is flush with the underside of the table A-frame
and proceed to step 5. If you are building the 3ft
version please refer to Step 8 before proceeding with
Step 5.

Oakham picnic bench
Rutland County Garden Furniture Ltd, Ashbourne House, 2 Dovecote Meadows,
Aslackby, Sleaford, Lincs, NG34 0HZ.
Company No: 7670072 VAT No: 151744027
3
Step 5
Step 6
Ensure that the brace is lined up centrally on the
table and attach it to the A-frame with a coach screw.
Make sure that the brace is still aligned centrally on
the table and affix the other end to the table top with
a coach screw as shown. Repeat steps 3 -6 to finish
the table assembly and proceed to step 8.
Step 7
Step 8
For the 3ft version steps 4 - 7 should be carried out
but with the braces in an offset configuration as
shown above and not centred on the table top.
Now proceed with Step 5.
Turn the table assembly right side up in preparation
for attaching the seat panels.

Oakham picnic bench
Rutland County Garden Furniture Ltd, Ashbourne House, 2 Dovecote Meadows,
Aslackby, Sleaford, Lincs, NG34 0HZ.
Company No: 7670072 VAT No: 151744027
4
Step 9
Step 10
Place one of the seat panels in position as shown as
and proceed to step 10.
Align the seat panel batten with the outer end of the
A-frame as shown and repeat for the other end of the
seat panel.
Step 11
Step 12
Using the coach screws provided attach the seat
panel to the A-frame at both ends of the bench.
Please note that the children's version will have only
one screw at either end.
Repeat steps 9-11 for the other seat panel.
Finally, cover any exposed coach screw heads with
the cover caps provided. Your Oakham picnic bench is
now complete.
We hope that you found your product quick and easy to assemble but if not and you require any
further assistance or have any questions you can contact us by telephone on: 01778 440803
Email: [email protected]
www.rutlandcountygardenfurniture.co.uk