Rutland County The Barrowden set User manual

Assembly Instructions
The Barrowden set
1
Before you commence the assembly process we recommend that you read these instructions thoroughly beforehand to
familiarise yourself with the assembly process and to also check that you have the correct components. If for any reason you
need assistance, you can find our contact details on the final page of these instructions.
We highly recommend that any assembly is carried out on a flat, level surface if possible and that you use another person to
assist you if necessary.
Please note: Whilst a single width seat is shown here, the assembly process is identical for all Barrowden seat models.
When checking your components, only the companion and combo seats will contain the table section element. Also, the
components listed are per seat so these will be doubled or tripled in quantity depending on the model you have purchased.
The assembly process shown here is for our Barrowden dining table. However, the same process applies to all of our
Barrowden table models.
Tools required:
13mm and 10mm socket or spanner, Hammer
Components
M8 Nut, bolt and
washers
1 x M8 120mm
coachscrew
1 x Seat back panel
1 x Seat panel
1 x Right arm frame
1 x Left arm frame
(Optional) Angled
table section(s)
(Optional) Straight
table section(s)
1 x Table top
4 x Table leg

The Barrowden set
Rutland County Garden Furniture Ltd, Ashbourne House, 2 Dovecote Meadows,
Aslackby, Sleaford, Lincs, NG34 0HZ.
Company No: 7670072 VAT No: 151744027
2
Step 1
Step 2
Attach the Left arm frame to the Seat panel as shown
using 4 of the M8 bolts. If required, use a hammer to
drive the bolts fully home...
...and secure in place with 4 of the washers and nuts as
shown. Do not fully tightens the nuts at this stage.
Step 3
Step 4
Affix the Right arm frame to the other side of the Seat
panel in the same way.
Position the Seat back panel as shown and fix into place using
the remaining fixings, again using a hammer if neccessary.
Now fully tighten all of the nuts and bolts. The Barrowden
seat is now complete. For companion seats, please consult
step 5 onwards.

The Barrowden set
Rutland County Garden Furniture Ltd, Ashbourne House, 2 Dovecote Meadows,
Aslackby, Sleaford, Lincs, NG34 0HZ.
Company No: 7670072 VAT No: 151744027
3
Step 5
Step 6
For a double or triple seat attach the centre strut of the
Seat panel to the Seat back panel using the M8 120mm
coachscrew .
For an angled companion seat place 2 Barrowden seats as
shown - at an angle of around 60° to each other. Now
lower the table section into place. Adjust the position of
the seats so that the seat edges are aligned with the table
section outer frame.
Step 7
Step 8
For a straight companion seat place 2 seats parallel to each
other and 21cm apart. Now lower the table section into
place.
If necessary slide the table section backwards until it stops.

The Barrowden set
Rutland County Garden Furniture Ltd, Ashbourne House, 2 Dovecote Meadows,
Aslackby, Sleaford, Lincs, NG34 0HZ.
Company No: 7670072 VAT No: 151744027
4
Step 9
Step 10
Place the table top upside down as shown and take one leg
so that the holes in the leg are aligned with those in the
table top.
Now push 2 of the M8 bolts into the holes, using the
hammer if necessary to drive the bolts fully into place.
Step 11
Step 12
Place an M8 washer and nut onto each bolt and fully
tighten.
Repeat adding legs in the same fashion until all 4 are
attached securely. Your Barrowden set is now complete.
We hope that you found your product quick and easy to assemble but if not and you require any further assistance or have
any questions you can contact us by telephone on: 01778 440803
Email: [e-mail] www.rutlandcountygardenfurniture.co.uk