S.R.Smith rogue2 User manual

06-821 S.R. SMITH, LLC 2013 OCT14
ROGUE2
SLIDE OWNER’S MANUAL
SRS AUSTRALIA, PTY LTD
12 Enterprise St
Richlands QLD 4077
Australia
Phone [phone] •Fax [phone]
www.srsmith.com/au
S.R. SMITH, LLC
CORPORATE HEADQUARTERS
P.O. Box 400 • 1017 S.W. Berg Parkway
Canby, Oregon 97013
USA
Phone [phone] • Fax [phone]
www.srsmith.com

2
TABLE OF CONTENTS
SLIDE WARNING AND SAFETY SUMMARY........................................................................................................2
INTENDED USE INSTRUCTIONS...........................................................................................................................3
INSTALLED ROGUE2 STRUCTURAL & INSTALLATION CHECKLIST ...........................................................4
DAILY/WEEKLY MAINTENANCE OF THE ROGUE2 ..........................................................................................5
APPLICABLE STANDARDS AND CODES ............................................................................................................5
ASSEMBLY AND INSTALLATION...........................................................................................................................5
DRAWINGS.................................................................................................................................................................5
SUBSEQUENT OWNERS.........................................................................................................................................5
MANUFACTURER’S PLACEMENT INSTRUCTIONS..........................................................................................6
CLEANING INSTRUCTIONS....................................................................................................................................8
SLIDE WARNING AND SAFETY SUMMARY
DANGER –FAILURE TO FOLLOW THESE WARNINGS, INSTRUCTIONS AND THE
OWNER’S MANUAL MAY RESULT IN SEROUS INJURY OR DEATH
HEAD FIRST SLIDES ARE STRICTLY PROHIBITED
TO REDUCE THE POSSIBILITY OF INJURY, IT IS NECESSARY THAT THE USER
KNOW THAT THE CHIEF DANGER OF HEAD FIRST SLIDING IS SERIOUS SPINAL
INJURY. INJURIES TO THE SPINE MAY RESULT IN TEMPORARY OR
PERMANENT PARALYSIS OR EVEN DEATH. RESEARCH STUDIES HAVE
SHOWN THAT YOU CANNOT RELY ON THE WATER TO SLOW YOU DOWN
SUFFICIENTLY TO AVOID INJURY.
DO NOT SLIDE HEAD FIRST
DO NOT SLIDE HEAD FIRST

3
INTENDED USE INSTRUCTIONS
THE ROGUE2 SLIDE IS DESIGNED AND MANUFACTURED FOR INSTALLATION
AND USE ON INGROUND SWIMMING POOLS ONLY. DO NOT INSTALL THE
ROGUE2 SLIDE ON ABOVE GROUND POOLS, HOUSEBOATS, BOAT DOCKS,
FLOATING DOCKS OR PLATFORMS, OR OTHER BODIES OF WATER SUCH AS
LAKES, PONDS, RIVERS, ETC. PROPER ASSEMBLY, INSTALLATION, USE, AND
SUPERVISION IS ESSENTIAL FOR PROPER OPERATION AND TO REDUCE THE
RISK OF SERIOUS INJURY OR DEATH.
1. SLIDE FEET FIRST ONLY AS SHOWN IN FIGURE 1. DO NOT SLIDE HEAD FIRST
2. ONLY ONE PERSON ALLOWED ON THE SLIDE AT A TIME WITH A MAXIMUM USER
WEIGHT OF 250 LB (113 KG).
3. ADULT SUPERVISION REQUIRED AT ALL TIMES WHEN CHILDREN ARE USING THE SLIDE.
4. HOLD ONTO HANDRAILS AT ALL TIMES WHEN USING THE LADDER.
5. NO ROUGHHOUSING OR HORSEPLAY ON SLIDE.
6. DO NOT JUMP OR DIVE FROM ANY PART OF THE SLIDE.
7. FAMILIARIZE YOURSELF WITH THE SHAPE OF THE POOL BOTTOM AND THE WATER
DEPTH BEFORE YOU SLIDE. SLIDE FEET FIRST ONLY.
8. DO NOT SLIDE UNTIL ALL SUBMERGED OBSTACLES, SURFACE OBJECTS OR OTHER
SWIMMERS ARE CLEAR OF THE SLIDER’S PATHWAY.
9. DO NOT USE THE SLIDE WHILE UNDER THE INFLUENCE OF ALCOHOL OR DRUGS.
10. DON’T SLIDE ALONE; USE THE BUDDY SYSTEM.
11. TAKE YOUR TIME IN PREPARING TO SLIDE. MOVE FORWARD SLOWLY AND GET
YOURSELF POSITIONED PROPERLY BEFORE STARTING THE SLIDE.
12. ONLY PERSONS HEALTHY ENOUGH FOR WATER ACTIVITIES SHOULD USE THE SLIDE.
PERSONS WITH MEDICAL CONDITIONS, INCLUDING PREGNANCY, SHOULD CONSULT
THEIR DOCTOR BEFORE USING THE SLIDE. PERSONS WITH PHYSICAL DISABILITIES
SHOULD USE CAUTION AND MAY REQUIRE ASSISTANCE.
13.DO NOT USE THE SLIDE IF ANY PART OF IT BECOMES DAMAGED, WEAKENED, OR
BROKEN. HAVE THE SLIDE INSPECTED AND, IF NECESSARY, REPAIRED BY A POOL
PROFESSIONAL, WHO IS FAMILIAR WITH WATER SLIDES BEFORE USING THE SLIDE.
SEE INSTALLED SLIDES’ STRUCTURAL & INSTALLATION CHECKLIST.
READ AND FOLLOW ALL SAFETY RULES
LISTED BELOW.
MAKE SURE THAT EVERYONE WHO USES
THE ROGUE 2 KNOWS AND FOLLOWS ALL
RULES.
CHILDREN MUST BE SUPERVISED BY AN
ADULT AT ALL TIMES WHEN USING THE
SLIDE.

4
PROPER SLIDING POSITION
Slide users must use the sitting slide position, facing forward, feet first as shown in
Figure 1.
INSTALLED ROGUE2 STRUCTURAL & INSTALLATION CHECKLIST
After installation and prior to the first use of the ROGUE2 and periodically (see
DAILY/WEEKLY MAINTENANCE OF THE ROGUE2) thereafter the owner must:
1. INSPECT THE RUNWAY FOR VISIBLE CRACKS OR TEARS.
3. INSPECT THE LADDER FOR SHARP EDGES, PROTRUSIONS, CRACKS OR TEARS.
4. INSPECT LADDER AND PEDESTAL MOUNTING AREAS FOR LOOSE OR CORRODED
FASTENERS.
5. MEASURE THE FOLLOWING DIMENSIONS AND COMPARE WITH THE MANUFACTURER’S
PLACEMENT INSTRUCTIONS ON PAGES 5, 6, AND 7.
POOL WATER DEPTH AT THE BASE OF THE SLIDE SHOULD BE AT LEAST 3’ (914 MM) DEEP, AND AT
4’6” (1372 MM) OUT FROM SLIDE EXIT, SHOULD BE AT LEAST 4’6” (1372 MM) DEEP.
THE HEIGHT OF THE SLIDE RUNWAY EXIT ABOVE THE WATER SHOULD BE 20” (508 MM) MAXIMUM.
THE DISTANCE BETWEEN THE SLIDE CENTERLINE AND THE EDGE OF OTHER POOL EQUIPMENT
SHOULD BE AT LEAST 3’6” (1067 MM).
6. OBSERVE THE POSITION OF THE EXIT OF THE SLIDE AS SHOWN IN FIGURES 2, 3 AND 5
ON PAGES 6 AND 7.
7. READ, UNDERSTAND AND ENFORCE ALL SAFETY AND USE INSTRUCTIONS ON THE
SLIDE.
Figure 1

5
DAILY/WEEKLY MAINTENANCE OF THE ROGUE2
1. When hosing down the deck, hose your Rogue2 to wash away any dust, dirt or other debris,
which may have accumulated.
2. Be sure that all connections are secure. Tighten hardware if necessary.
3. All polyethylene parts require little maintenance. Hose and wipe to clean.
While cleaning slide, check and see that all nuts and bolts are tight and secure.
4. Inspect the runway for visible cracks or tears, sharp edges and protrusions.
5. Inspect all attachment points for loose or corroded fasteners.
6. Inspect all ladder tread or step-attachment points for evidence of shear, bending yield, or fatigue
in the ladder steps, rails, or attachments means. Yield is evidenced by crystallization or fine
cracking of the ladder tread and/or surface.
7. Inspect the ladder handrails for rigidity and attachment.
APPLICABLE STANDARDS AND CODES
The installation of the Rogue2 must comply with all applicable governmental and building codes.
ASSEMBLY AND INSTALLATION
All S.R. Smith Rogue2 slides are inspected prior to shipment from the factory. Proper assembly and
installation is mandatory. Improper assembly and installation voids S.R. Smith’s warranty and may affect
the safety of the user. It is the installer’s responsibility to ensure that the structural integrity of the
concrete pad prior to installation of the slide.
DRAWINGS
All drawings in this Slide Owner’s Manual (Figures 1 through 5) are for illustration purposes only and are
NOT TO SCALE.
SUBSEQUENT OWNERS
The Owner’s Manual must remain with the owner of the slide. If the owner changes, the Owner’s Manual
shall be brought to the attention of the new owner.

6
MANUFACTURER’S PLACEMENT INSTRUCTIONS
THE SLIDE OWNER MUST REVIEW THE MANUFACTURER’S PLACEMENT INSTRUCTIONS WITH
THE INSTALLER TO ENSURE THAT THE MANUFACTURER’S INSTALLATION REQUIREMENTS
HAVE BEEN MET.
PROPER ASSEMBLY, INSTALLATION, USE AND SUPERVISION IS ESSENTIAL FOR PROPER
OPERATION AND TO REDUCE THE RISK OF SERIOUS INJURY OR DEATH.
1. The critical dimensions for placement of the heliXTM are as shown in FIGURES 2 and 3.
A. The slide exit runway surface shall not exceed 20” (508 mm) above the water surface as shown
in FIGURE 2.
B. The slide shall be positioned so that all water flowing off the runway exit drops into the pool.
Recommended overhang is 4” (102 mm).
C. The minimum depth of water below the exit lip of the slide shall be 3’ (914 mm) and increases to
4’-6” (1372 mm) at Pt. A, which is a distance of 4’-6” (1372 mm) from the exit lip of the slide as
shown in FIGURE 2.
D. A minimum depth of 4’-6” (1372 mm) shall be maintained at a distance of 9’ (2743 mm) along the
extended centerline of the slide from Pt. A. as shown in FIGURE 2.
2. A minimum clearance area in front of the slide shall be maintained at all
times as follows:
The minimum clearance distance on either side of the extended centerline of
the slide runway shall not be less than 3’-6” (1067 mm) at a point no less than
2’-6” (762 mm) from the exit lip of the slide and extending a distance of 13’-6”
(4115 mm) in front of the slide as shown in FIGURE 3.
DECK/COPING SURFACE
3' MIN.
EXIT
RUNWAY SURFACE
PLUMBLINE
20" MAX.
WATER LEVEL
ENTRANCE
Pt.A
13'-6" MIN.
9' MIN. 4'-6"
4'-6" MIN.4'-6" MIN.
FIGURE 3
FIGURE 2
Dimensions are in feet/inches and (millimeters)
(508mm)
(1372mm)
(2743mm)
(4115mm)
(914mm)

7
3. SLIDE PLACEMENT INSTRUCTIONS FOR INSTALLATIONS ON POOLS WITH OTHER SLIDES
AND/OR DIVING BOARDS
A. The minimum clearance area in front of a properly installed diving board on an inground
swimming pool is a minimum distance of 3’-6” (1067 mm) on either side of the board’s centerline
as shown in FIGURE 4. Pt. C extends a minimum distance of “C” from the tip end of the board as
shown in FIGURE 4. The width distance “W” on either side of Pt. C is given in CHART 1 and
shown in FIGURE 4.
“C” DIMENSION FOR BOARD = AB + BC
“W” DIMENSION FOR BOARD = WIDTH AT PT.C
A. The minimum clearance area of a slide or diving board shall not intersect any coping or rope and
float line as shown in FIGURE 5. The minimum clearance area of a slide or diving board may
intersect each other provided that they are not used simultaneously.
CHART 1
BOARD MINIMUM CLEARANCE AREA
POOL TYPE
“C” DIMENSION
“W” DIMENSION
I
14’-6” (4420mm)
5’-0” (1524mm)
II
14’-6” (4420mm)
6’-0” (1829mm)
III
16’-6” (5029mm)
6’-0” (1829mm)
IV
18’-6” (5639mm)
7’-6” (2286mm)
V
21’-0” (6401mm)
7’-6” (2286mm)
See Article 5 contained in ANSI/APSP/ICC-5 2011
STANDARD FOR RESIDENTIAL INGROUND SWIMMING
POOLS and refer to FIGURE 3 and Table 1 for Minimum
Water Envelope Dimensions AB, BC and Width at Point C.
FIGURE 5
FIGURE 4
(1067
mm)
(1067
mm)
Dimensions are in feet/inches and (millimeters)

8
CLEANING INSTRUCTIONS
Use nonabrasive soap and water when possible. In addition, you may safely use the
below listed products. Always try a test spot before applying to a large area.
Windex® With Ammonia Formula 409® Fantastik®
Soft Scrub® Scrubfree Tackle®
Glass Plus® Topjob® Tilex®
Always read the label instructions on any cleaner carefully before applying it to a
polyethylene surface.
AVOID HARSH CHEMICALS AND DISINFECTANTS. DO NOT USE:
Dow with Scrubbing Bubbles® Lysol® Disinfectant Ajax® Cleanser
Windex® With Vinegar White Cap® Ajax® Liquid
Serious Equipment, Serious Fun!
Product Name: Rogue2
Serial Number: ___________________ (located on label attached to slide)
Purchase Date:____________________
To register your slide and find information on the full line of S.R. Smith deck equipment
please visit www.srsmith.com.
Like us www.facebook.com/srsmithpools