S.R.Smith rogue2 User manual

06-821 S.R. SMITH, LLC 2006 OCT13
CORPORATE HEADQUARTERS
WESTERN SALES AND MANUFACTURING PLANT
P.O. Box 400 1017 SW Berg Parkway
Canby, Oregon 97013
Phone: [phone] Fax: [phone]
www.srsmith.com
SLIDE OWNERS MANUAL

2
Table of Contents
Topic Page#
SLIDE WARNING AND SAFETY SUMMARY........................................................................................................3
INTENDED USE INSTRUCTIONS...........................................................................................................................4
INSTALLED ROGUE2 STRUCTURAL & INSTALLATION CHECKLIST...........................................................5
DAILY/WEEKLY MAINTENANCE OF THE ROGUE2..........................................................................................5
APPLICABLE STANDARDS AND CODES ............................................................................................................5
ASSEMBLY AND INSTALLATION...........................................................................................................................5
DRAWINGS.................................................................................................................................................................6
SUBSEQUENT OWNERS.........................................................................................................................................6
MANUFACTURER’S PLACEMENT INSTRUCTIONS..........................................................................................6
CLEANING INSTRUCTIONS....................................................................................................................................8

3
SLIDE WARNING AND SAFETY SUMMARY
DANGER – FAILURE TO FOLLOW THESE WARNINGS, INSTRUCTIONS AND THE
OWNER’S MANUAL MAY RESULT IN SEROUS INJURY OR DEATH
HEAD FIRST SLIDES ARE STRICTLY PROHIBITED
TO REDUCE THE POSSIBILITY OF INJURY, IT IS NECESSARY THAT THE USER
KNOW THAT THE CHIEF DANGER OF HEAD FIRST SLIDING IS SERIOUS SPINAL
INJURY. INJURIES TO THE SPINE MAY RESULT IN TEMPORARY OR
PERMANENT PARALYSIS OR EVEN DEATH. RESEARCH STUDIES HAVE
SHOWN THAT YOU CANNOT RELY ON THE WATER TO SLOW YOU DOWN
SUFFICIENTLY TO AVOID INJURY.
DO NOT SLIDE HEAD FIRST
READ AND FOLLOW ALL SAFETY RULES
LISTED BELOW.
MAKE SURE THAT EVERYONE WHO USES
THE ROGUE 2 KNOWS AND FOLLOWS ALL
RULES.
CHILDREN MUST BE SUPERVISED BY AN
ADULT AT ALL TIMES WHEN USING THE
SLIDE.

4
INTENDED USE INSTRUCTIONS
THE ROGUE2 SLIDE IS DESIGNED AND MANUFACTURED FOR INSTALLATION
AND USE ON INGROUND SWIMMING POOLS ONLY. DO NOT INSTALL THE
ROGUE2 SLIDE ON ABOVE GROUND POOLS, HOUSEBOATS, BOAT DOCKS,
FLOATING DOCKS OR PLATFORMS, OR OTHER BODIES OF WATER SUCH AS
LAKES, PONDS, RIVERS, ETC. PROPER ASSEMBLY, INSTALLATION, USE, AND
SUPERVISION IS ESSENTIAL FOR PROPER OPERATION AND TO REDUCE THE
RISK OF SERIOUS INJURY OR DEATH.
1. ONLY ONE PERSON ALLOWED ON THE SLIDE AT ANY GIVEN TIME.
2. SLIDE FEET FIRST ONLY AS SHOWN IN FIGURE 1. DO NOT SLIDE HEAD
FIRST
3. HOLD ONTO HANDRAILS AT ALL TIMES WHEN USING THE LADDER.
4. NO ROUGHHOUSING OR HORSEPLAY ON SLIDE.
5. DO NOT JUMP OR DIVE FROM ANY PART OF THE SLIDE.
6. FAMILIARIZE YOURSELF WITH THE SHAPE OF THE POOL BOTTOM AND
THE WATER DEPTH BEFORE YOU SLIDE. SLIDE FEET FIRST ONLY.
7. DO NOT SLIDE UNTIL ALL SUBMERGED OBSTACLES, SURFACE OBJECTS
OR OTHER SWIMMERS ARE CLEAR OF THE SLIDER’S PATHWAY.
8. DO NOT USE THE SLIDE WHILE UNDER THE INFLUENCE OF ALCOHOL OR
DRUGS.
9. DON’T SLIDE ALONE; USE THE BUDDY SYSTEM.
10.TAKE YOUR TIME IN PREPARING TO SLIDE. MOVE FORWARD SLOWLY
AND GET YOURSELF POSITIONED PROPERLY BEFORE STARTING THE
SLIDE.
11.ONLY PERSONS HEALTHY ENOUGH FOR WATER ACTIVITIES SHOULD
USE THE SLIDE. PERSONS WITH MEDICAL CONDITIONS, INCLUDING
PREGNANCY, SHOULD CONSULT THEIR DOCTOR BEFORE USING THE
SLIDE. PERSONS WITH PHYSICAL DISABILITIES SHOULD USE CAUTION
AND MAY REQUIRE ASSISTANCE.
12.DO NOT USE THE SLIDE IF ANY PART OF IT BECOMES DAMAGED,
WEAKENED, OR BROKEN. HAVE THE SLIDE INSPECTED AND, IF
NECESSARY, REPAIRED BY A POOL PROFESSIONAL, WHO IS FAMILIAR
WITH WATER SLIDES BEFORE USING THE SLIDE. SEE INSTALLED SLIDES’
STRUCTURAL & INSTALLATION CHECKLIST.
13.MAXIMUM WEIGHT CAPACITY FOR THE SLIDE IS 250 LBS.
PROPER SLIDING POSITION
Slide users must use the sitting slide position, facing forward, feet first as shown in
Figure 1.
Figure 1

5
INSTALLED ROGUE2 STRUCTURAL & INSTALLATION CHECKLIST
After installation and prior to the first use of the ROGUE2 and periodically (see
DAILY/WEEKLY MAINTENANCE OF THE ROGUE2) thereafter the owner must:
1. Inspect the runway for visible cracks or tears.
2. Inspect the ladder for sharp edges, protrusions, cracks or tears.
3. Inspect ladder and pedestal mounting areas for loose or corroded fasteners.
4. Measure the following dimensions and compare with the Manufacturer’s
Placement Instructions on pages 5, 6, and 7.
Measure the depth of water in front of the slide exit. (4-6”) min. depth at a
distance of (4-6”) from exit end of slide.
Measure the height of the slide runway exit above the water. (20” max.)
Measure the distance between the slide centerline and the edge of other
pool equipment.
5. Observe the position of the exit of the slide as shown in Figures 2, 3 and 5 on
pages 6 and 7.
6. Read, understand and enforce all safety and use instructions on the slide.
DAILY/WEEKLY MAINTENANCE OF THE ROGUE2
1. When hosing down the deck, hose your Rogue2 to wash away any dust, dirt or
other debris, which may have accumulated.
2. Be sure that all connections are secure. Tighten hardware if necessary.
3. All polyethylene parts require little maintenance. Hose and wipe to clean.
While cleaning slide, check and see that all nuts and bolts are tight and secure.
4. Inspect the runway for visible cracks or tears, sharp edges and protrusions.
5. Inspect all attachment points for loose or corroded fasteners.
6. Inspect all ladder tread or step-attachment points for evidence of shear, bending
yield, or fatigue in the ladder steps, rails, or attachments means. Yield is
evidenced by crystallization or fine cracking of the ladder tread and/or surface.
7. Inspect the ladder handrails for rigidity and attachment.
APPLICABLE STANDARDS AND CODES
The installation of the Rogue2 must comply with all applicable governmental and
building codes.
ASSEMBLY AND INSTALLATION
All S.R. Smith Rogue2 slides are inspected prior to shipment from the factory. Proper
assembly and installation is mandatory. Improper assembly and installation voids S.R.
Smith’s warranty and may affect the safety of the user. It is the installer’s responsibility
to ensure that the structural integrity of the concrete pad prior to installation of the slide.

6
DRAWINGS
All drawings in this Slide Owner’s Manual (Figures 1 through 5) are for illustration
purposes only and are NOT TO SCALE.
SUBSEQUENT OWNERS
The Owner’s Manual must remain with the owner of the slide. If the owner changes, the
Owner’s Manual shall be brought to the attention of the new owner.
MANUFACTURER’S PLACEMENT INSTRUCTIONS
THE SLIDE OWNER MUST REVIEW THE MANUFACTURER’S PLACEMENT
INSTRUCTIONS WITH THE INSTALLER TO ENSURE THAT THE MANUFACTURER’S
INSTALLATION REQUIREMENTS HAVE BEEN MET.
PROPER ASSEMBLY, INSTALLATION, USE, AND SUPERVISION IS ESSENTIAL FOR
PROPER OPERATION AND TO REDUCE THE RISK OF SERIOUS INJURY OR DEATH.
1. The critical dimensions for placement of the Rogue2 slide are as shown in Figures 2
and 3.
A. The slide exit runway surface shall not exceed twenty inches (20”) above the
water surface as shown in Figure 2.
B. The slide shall be positioned so that all water flowing off the runway exit drops
into the pool. Recommended overhang is (3”) inches.
C. The minimum depth of water below the exit lip of the slide shall be three feet (3’)
and increases to four feet six inches (4’-6”) at Pt. A, which is a distance of four
feet six inches (4’-6”) from the exit lip of the slide as shown in Figure 2.
D. A minimum depth of four feet six inches (4’-6”) shall be maintained at a distance
of nine feet (9’) along the extended centerline of the slide from Pt. A. as shown in
Figure 2.
FIGURE 2
DECK/COPING SURFACE
3' MIN.
EXIT
RUNWAY SURFACE
PLUMBLINE
20" MAX.
WATER LEVEL
ENTRANCE
Pt.A
13'-6" MIN.
9' MIN. 4'-6"
4'-6" MIN.4'-6" MIN.

7
2. A minimum clearance area in front of the slide shall be maintained at all times as
follows:
The minimum clearance distance on either side of
the extended centerline of the slide runway shall not
be less than three feet six inches (3’-6”) at a point
no less than two feet six inches (2’-6”) from the exit
lip of the slide and extending a distance of thirteen
feet six inches (13’-6”) in front of the slide as shown
in FIGURE 3.
3. SLIDE PLACEMENT INSTRUCTIONS FOR INSTALLATIONS ON POOLS WITH
OTHER SLIDES AND/OR DIVING BOARDS
A. The minimum clearance area in front of a properly installed diving board on an
inground swimming pool is a minimum distance of three feet six inches (3’-6”) on
either side of the board’s centerline as shown in FIGURE 4. Pt. C extends a
minimum distance of “C” from the tip end of the board as shown in FIGURE 4.
The width distance “W” on either side of Pt. C is given in CHART 1 and shown in
FIGURE 4.
FIGURE 3

8
“C” DIMENSION FOR BOARD = AB + BC
“W” DIMENSION FOR BOARD = WIDTH AT PT.C
A. The minimum clearance area of a slide or diving board shall not intersect any
coping or rope and float line as shown in FIGURE 5. The minimum clearance
area of a slide or diving board may intersect each other provided that they are
not used simultaneously.
CLEANING INSTRUCTIONS
Use nonabrasive soap and water when possible. In addition, you may safely use the
below listed products. Always try a test spot before applying to a large area.
Windex® With Ammonia Formula 409 ® Fantastik ®
Soft Scrub ® Scrubfree Tackle ®
Glass Plus ® Topjob ® Tilex ®
CHART 1
BOARD MINIMUM CLEARANCE AREA
POOL TYPE “C” DIMENSION “W” DIMENSION
I 14’-6” 5’-0”
II 14’-6” 6’-0”
III 16’-6” 6’-0”
IV 18’-6” 7’-6”
V 21’-0” 7’-6”
See Article 5 contained in ANSI/APSP/ICC-5 2011
STANDARD FOR RESIDENTIAL INGROUND SWIMMING
POOLS and refer to FIGURE 3 and Table 1 for Minimum
Water Envelope Dimensions AB, BC and Width at Point C.
FIGURE 5
FIGURE 4

9
Always read the label instructions on any cleaner carefully before applying it to a
polyethylene surface.
AVOID HARSH CHEMICALS AND DISINFECTANTS. DO NOT USE:
Dow with Scrubbing Bubbles ® Lysol ® Disinfectant Ajax ® Cleanser
Windex ® With Vinegar White Cap ® Ajax ® Liquid
Serious Equipment, Serious Fun!
Product Name: Rogue2
Serial Number: ___________________ (located on label attached to slide)
Purchase Date:____________________
To register your slide and find information on the full line of S.R. Smith deck equipment
please visit www.srsmith.com.
Like us www.facebook.com/srsmithpools