Saferhomee HB-5050G User manual

Manual Of Networking Alarm Panel
HB-5050G
NINGBO HENGBO TELECOMMUNICATION CO.,LTD

网络报警主机使用说明
1

网络报警主机使用说明
2
Connections of cables
Outputs Jumpers(Disable)：used to control the warning board status
+12: If AC powered,work normally;If DC powered,work abnormally
OUT: Alarming Mode,the warning board will light; Arm or Disarm
Mode,the warning board will blink;
Warning Board Interface：DC12V/0.5A outputs
Siren Interface：DC12V/0.5A outputs
Power Interface:DC15V/1.5A
SIM Card Slot: Only 2G SIM Card is available(Mini SIM)
Set Button: Restore to the factory default
Technical Parameters:
Working Voltage
DC 15V/1.5A
Backup Battery
12V/1.3Ah
Wireless Frequency
434.6MHz FSK
GSM Frequency
900/1800/1900/2100 MHz
Dimension
165x175x62（mm）

网络报警主机使用说明
3
Instructions
LCD Display:
-01/01 (01Blinking)
On Setting Mode
-F0
Restored to factory default
-F6
Connected to Server Success
No Display
Static working status,alarm panel has been
connected the detectors or remote controls
-XX (-Blinking)
learning detector status（XX：01…99 zone number）
_XX
Learned detector success（XX：01…99 zone number）
-XX
Alarm（XX：01…99 zone number）
-0X (-Blinking)
learning remotes status（X: 1-4 zone number）
_0X
Learned remotes success（X: 1-4 zone number）
-F5
Emergency Alarm(SOS)
-F7
Connect to server failure
-F2
Deleted account information success
-F8
SIM card faults
HXX
GPRS Signal less than 13（ＸX: 00-13）
-F1
Tamper
Indicator lights：
Red: Arm Status
Green：Disarm Status
Delete Account Information：Press the “Setting Button”Once,LCD
Display”-01”(01 Blinking),and then hold the “Setting Button”for
5 seconds ， Release the “setting button”when the LCD
Display”-F2”;
Restore to factory default：Press the “Setting Button”Once,LCD
Display”-01”(01 Blinking),and then hold the “Setting Button”for
10 seconds ， Release the “setting button”when the LCD
Display”-F0”;

网络报警主机使用说明
4
APP Operation Manual
App Interface(Home):
All Arm: On receiving all the alarm information mode
Disarm: On not receiving normal alarm information mode
Part Arm: Disable
Mute: Make the app silence when alarm
SOS：Emergency Help

网络报警主机使用说明
5
Account Setup(Account)
Press”Account”--- enter password:123456
SIM Card of the alarm panel supports SMS? No
Alarm Panel ID：Fill the 15-digits Serial Number/Scan the OR Code
Phone Number：The SIM Card number of the phone installed the App
Setup Password：123456
Press”Submit “

网络报警主机使用说明
6
Alarm Panel Setup(Settings)

网络报警主机使用说明
7
Phone Number
Total 4 groups phone number can be set
Standard Alarm Center SMS Number:Disable
Transfer Alarm Center SMS Number:Disable

网络报警主机使用说明
8
Detector
Select the zone number(1--99)
Select the zone type(Normal,Emergency,Fire,Help,Gas,Water)
Fill the Notes and save the notes
Press”Match “----and then trigger the detector once

网络报警主机使用说明
9
Remote Control
Select the remote control(1#--4#)
Press “+” to add the remote control
Press “-” to delete the remote control

网络报警主机使用说明
10
Timing Time
Query Timing Time: Querythe last timing time
2 groups of arm/disarm time can be set...press”√”to confirm.

网络报警主机使用说明
11
Password
Note:The password should be 6-digits
Ademco ID &Server’s Domain Address are used to communicate
with the SAFERHOMEE Alarm Software...(Disable)
Time(Disable)