9
Before starting, check the following points:
Make sure that the device does not contain any foreign parts.
Make sure that all the components are attached in their original placements.
Check manually that the fans do not rub or are not blocked.
Check the earth connection.
Make sure that the cover is properly closed.
1.3 Acceptance - Storage
In case of missing, non-conforming, or totally or partially damaged delivered products, the Purchaser must in
accordance with article 133-3 of the Commercial Code make written reservations on the transporter’s receipt
and confirm them within seventy-two (72) hours by sending a recommended letter to the transporter, as well
as a copy to the vendor. Acceptance of the equipment without any reservation will deprive the Purchaser of
any subsequent recourse against us.
The product must be stored in an area protected from bad weather, shocks and stains due to splashings or
splatterings of any kind during its transport from the supplier to the end customer and onto the worksite before
installation.
1.4 Warranty
The equipment is warranted twelve (12) months – Parts only – starting from the invoicing date.
The vendor agrees to replace the parts or the equipment whose operation is recognized defective by our
departments except for all damages and interests or penalties such as operating losses, commercial
prejudice, or other immaterial or indirect damages.
The following are not covered by our warranty: defects resulting from an abnormal usage or a usage not
conforming to the recommendations of our manuals ; faults observed as a consequence to normal wear ;
incidents caused by negligence, lack of monitoring, or servicing ; faults due to the incorrect installation of the
devices or to bad storage conditions before mounting.
In any case, the vendor will not be responsible for transformed equipment, repaired even partially.
SUMMARY
1. GENERAL ...................................................................................................................................................... 8
1.1 Warnings ......................................................................................................................................... 8
1.2 Safety instructions ......................................................................................................................... 8
1.3 Acceptance - Storage ..................................................................................................................... 9
1.4 Warranty .......................................................................................................................................... 9
2. PRODUCT PRESENTATION ...................................................................................................................... 10
3. INSTALLATION ........................................................................................................................................... 10
3.1 Dimensions and weights ............................................................................................................. 10
3.2 Installation .................................................................................................................................... 10
4. ELECTRIC CONNECTION .......................................................................................................................... 11
5. COMMISSIONNING ..................................................................................................................................... 12
6. SERVICING .................................................................................................................................................. 12
7. WASTE MANAGEMENT ............................................................................................................................. 12
7.1 Treatment of Packagings and non-dangerous wastes ............................................................. 12
7.2 Treatment of a Professional WEEE ............................................................................................. 12
1. GENERAL
1.1 Warnings
This product is manufactured according to rigorous technical safety rules in compliance with EC standards.
The EC declaration and the manual can be downloaded from the Internet (see URL on the last page).
Before installing and using this product, carefully read these instructions, which contain important indications
to ensure your safety and that of the users during the installation, commissioning and servicing of this product.
Once the installation is terminated, leave this manual in the machine for future consulting.
The installation of this product (implementation, connections, commissioning, and maintenance) and all other
interventions must be performed by a professional applying the recognized rules of good practice, standards
and safety regulations in force.
It must conform to the prescriptions related to Electromagnetic Compatibility (EMC) and the Low Voltage
Directive (LVD).
We advise all people exposed to risks to carefully respect accidents prevention standards. The responsibility
of the vendor would not be involved for any eventual body and/ or material damages caused whereas safety
instructions had not been respected or after product modifications.
Cabinet fans CAB-PLUS are designed for ventilation applications:
Indoor or outdoor installation
Permanent ambiance temperature: -20°C / +50°C
Relative humidity: max 95% non-condensing
Atmosphere not potentially explosive
Atmosphere with low salt content, without corrosive chemical agents
1.2 Safety instructions
Wear appropriate IPE (Individual Protection Equipment) before any intervention.
Before installing the cabinet fan, make sure that the support and placement are sufficiently resistant to
withstand the unit’s weight and that of the accessories.
Do not open the cover without first switching off the electrical power supply.
If the work is to be performed inside the device, switch off the electrical power supply on the main
circuit breaker and make sure that no one can accidentally switch it on.
Make sure that the moving parts are stopped.
Make sure that the motor driven fans are not accessible from the connection taps (connection duct or
screened protection).
