Sargent and Greenleaf 3007 Direct Drive User manual

Operating Instructions
Model 3006, 3007, 3028, 3029
GENERAL NOTES
• OrangeandBluewiresareusedtohookupexternalpower.
• RedandBlackwiresareusedtosetuptheduresssignal
• YellowandGreenwireswillbeusedtosetupremoteenable/disablesignal.
• Theauditfeatures,peripheraldevicesandaccessories,softwarefeatures,one-timecodefunctionality,USBfunctionality,wirelessfunctionality,remotefunctionality,and
otheradditionalfeaturesarebeyondthescopeoftheUL2058standardandnotpartoftheULListing.
• External Power Supply Requirements:UseonlyULListed/RecognizedCategoryAPHV/EPBU/QQGQ/QQGQ7externalpowersupplymeetingthefollowingspecifications.Connectorsand
wiresconnectingpowersupplytolockmustbeULListed/Recognized. Voltage:9–12VDC MaxCurrent:2A
Operation
Enable The Duress Alarm Feature
38* Programmer PIN Code# Option # Option #
Enabling the Duress alarm will allow the user to send a signal to the alarm system. ex: 38* 00123456# 2# 2#
Enable for Duress Output (Black and Red wires)
37* Programmer PIN Code# Output # Function # Function#
Enabling the Duress Ouput function 1 does not require a special module to send the signal. ex: 37* 00123456# 1# 1# 1#
Enable The Remote Enable/Disable Feature (Green and Yellow wires)
36* Programmer PIN Code# Option # Function # Function #
Enable the Remote Enable function 3 when the loop is closed. ex: 36* 00123456# 1# 3# 3#
Enable the Remote Enable function 4 when the loop is closed. ex: 36* 00123456# 1# 4# 4#
Sargent & Greenleaf S.A.
9, Chemin du Croset
1024 Ecublens, Switzerland
Phone: [phone]
Fax: [phone]
Document630-935
Revised08/24/2018
Sargent & Greenleaf, Inc.
One Security Drive
Nicholasville, KY 40356 USA
Phone: [phone]
Fax: [phone]
Copyright©2017, Sargent & Greenleaf, Inc.
Digital Platform Alarm Cable for Duress/Remote Enable/Remote Disable/External Power
White Cable Future Features
Brown Cable
Yellow Cable Common
Green Cable Input 0-5 Volt
Red Cable Open Drain output (200 milliamp continuous current)
Black Cable 10 kOHM pullup to sys Power
Orange Cable Power (-)
Blue Cable Power (+) 9- 12 volts DC/ 2 amps
* - UL Rated 9 - 12VDC 2A Rated Supply

Installation
3006 and 3007
Placethelockcaseonitscoverside.Removethesteelplatethatcoversthelockcasebyremovingthethreescrewswhichholditinplace.Thiswill
requireyoutoremovethescrewunderthesticker.Whenremovingthesteelplatetomakesurethedrivecamandwhiteplasticwasherstayin
place.TheareacircledinREDisthelocationwherethiscablewillbeinstalled.
Observetheconnecteranditsorientation.Thiswillbeimportantwhenpluggingtheconnectionintothelock.Linetheplugandconnectorupso
thattheyareinthesameorientation.
Oncetheconnectionbetweenthelockandcableiscompleted,thecableshouldberoutedinthespaceprovided.Oncethemetalcoverisreattached,
thisroutingwillavoidthecablefrombeingpinched.Thecableshouldberoutedasshown.Usingthescrewsremovedintherststep,replacethe
coverandtighten.
3028 and 3029
Wheninstallingthecableintothe3028/3029lockmechanisms,nocoverneedstoberemoved.Accessisavailableatthecircledconnectionpoint
onthesideofthelock.
Orientation of the pins on a 3028/3029
Orientation of the pins on a 3006/3007