Sargent and Greenleaf 6860 User manual

Installation and Operating Instructions for:
6860, 6870, 6880, 6890 Key Operated Safe Lock
This Sargent & Greenleaf key operated safe lock combines ease of
key changing with a very high level of security. Its advanced design
makes it easy to operate and easy to change keys. Follow these
instructions carefully to get the best possible service from your lock.
Precautions:
• Read this entire page before you begin to change the keys.
• Keep the safe door open until the lock has been successfully
changed to new keys and checked.
• Never force the lock or key.
• Always keep your key(s) in a safe place.
• If a key is lost or misplaced, change the lock to a new key as soon as
possible, even if the original key is recovered.
Key Changing Procedure:
The key changing procedure is very simple. Follow these basic
precautions to prevent problems:
STEP 1. Open the safe door. If the door incorporates boltwork, turn
the safe handle to extend the bolts fully.
STEP 2. With the door open, turn the key counterclockwise to its
stop, and remove it from the lock.
STEP 3. Locate the changing button on the back of the lock. Use a
probe (such as the tip of a ball point pen) to depress the
button. Keep the button depressed for Step 4.
STEP 4. Insert the old key and turn it clockwise 180º until it reaches
its stop. Release the changing button and remove the key.
STEP 5. Insert the new key and turn it counterclockwise 180º to its
stop. Remove the new key. Your lock is now set to the new
key, and the old key is no longer operable.
STEP 6. Check the operation of the new key(s) in your lock at least
three times before closing the safe door.
Follow These Basic Considerations and Precautions:
• The bolt of the Key Lock can withstand an end load up to 1.8 lbs. (8 N).
Forces greater than this amount may prevent the lock from working properly.
• The key requires a minimum keyhole diameter of ½ inch (12,7 mm).
If a guide tube is used with the lock, the minimum diameter increases to
11/16 inch (17,5 mm).
• Installer modications to the Key Lock are not covered by the
manufacturer’s warranty.
• Take precautions to prevent metal shavings, safe insulation, paint, weld
spatter, or other foreign material from entering the lock.
• Make sure the lock is not installed in a manner that will allow objects to come
in contact with the changing button.
• The lock can be mounted right-hand (RH), left-hand (LH), vertical-up (VU),
or vertical-down (VD).
• It is recommended the safe incorporate a relock device, or have a plate of
at least 12-gauge steel attached to the back of the lock. Plate dimensions
are given in the drawing at right. Attaching screws must be inserted into
the blind holes on the lock’s back.
• The lock should only be serviced and lubricated by trained service
personnel. Improper service or lubrication will damage the lock and void
the manufacturer’s warranty.
Note: The key is always to be removed after the opening
and locking procedure so that no unauthorized person has
access to the key. Always keep your key(s) in a safe place.
CHANGING BUTTON
1.86”
1.5”
2.375”
47,2 mm
38,1 mm
60,3 mm
ATTACH PLATE TO LOCK USING (2) 8-32X
3/8”THREAD FORMING SCREWS
Installation Procedure
STEP 1. Insure that the mounting surface for
the lock is smooth and at, and that the
keyhole is perpendicular to the
mounting surface.
STEP 2. Attach the lock to the mounting surface
using three ¼-20 or three M6 machine
screws, depending on the dimensions
of the screw threads in the mounting
surface. An Option or Recommendation:
Attach the safe relock device or
recommended 12-gauge back plate.
(see illustration above).
SAFE DOOR
LOCK BODY
LOCK BOLT
GUIDE
TUBE
ESCUTCHEON
Document 630-011
Revised 3/28/2016
• Für Anweisungen auf Deutsh besuchen Sie bitte die folgende Website:
• Pour obtenir les instructions en français, veuillez consulter le site ci-dessous: www.sargentgreenleaf.com/OPinstr.php
For S&G/FAS
Double-Bitted Key Locks

Installation Procedure (Cont.)
STEP 3. A guide tube should be used on insulated and composite safes.
The tube must be cut to a length equal to the safe door thickness
plus 3/16 inch (4,76 mm). This will cause the tube to mate with the
pattern surrounding the keyhole and the pattern in the underside of
the escutcheon. Remove all sharp edges, burrs, and metal shavings
created when the tube is cut.
STEP 4. Attach the escutcheon to the outside surface of the safe door over
the keyhole.
STEP 5. Check the operation of the key in the lock. There should be no binding
or scraping of the key against the tube or the sides of the keyhole.
It should turn easily and smoothly.
STEP 6. Check the operation of the new key(s) in your lock at least three times
before closing the safe door.
STEP 7. Make sure the lock bolt does not drag or bind against the safe’s bolt
work or door frame (rebate).
Sargent & Greenleaf / FAS Key Operated Safe Lock EN1300 Specications
Attaching Screws: Use only the screws provided with the Lock. They must engage the mounting plate by at least four full threads. Do not use lock washers or thread sealing compounds.
Recommended Attaching Screw Torque: 30 to 40 inch-pounds [33.9 to 45.2 dNm]
Minimum/Maximum Spindle Hole Diameter: The key requires a minimum keyhole of ½ inch (12,7 mm) and a maximum keyhole of 0.56 inch (14,2 mm). If a guide tube is used with the lock,
the minimum diameter increases to 11/16 inch (17,5 mm) and the maximum diameter to 0.72 inch (18,3 mm).
Lock is Designed to Move: 0 lbs. (0 Newtons) continuous or maximum.
Lock Bolt Maximum Free Movement: 0.445 inch (11,3 mm). At least 0.106 inch (2,70 mm) of the lock bolt remains outside the edge of the lock case when bolt is fully retracted.
Maximum Bolt End Pressure: The bolt of the Key Lock can withstand an end load up to 1.8 lbs. (8 Newtons). Forces greater than this amount may prevent the lock from working properly.
Maximum Bolt Side Pressure: The safe and container boltwork or locking cam designs must never apply any side pressure on the lock bolt.
Mounting Environment: The lock body is designed to be mounted inside a secure container. Precautions must be made to prevent metal shavings, safe insulation, paint, weld spatter, or other
foreign material from entering the lock.The container must be constructed to oer protection against physical attack directed at the lock.The amount of protection is dependent on the desired level
of security for the system as a whole. Lock protection may include barrier materials, relock devices, thermal barriers, thermal relock components, or any combination of these. Relock device attach-
ing screws must NOT be longer than the depth of the tapped attaching screw hole pro- vided in the lock case. A minimum distance of 0.150 inch (3,8 mm) is recommended between the end of the
lock case and the closest approach of the safe’s blocking bar or cam plate (which is normally blocked by the extended lock bolt). Maintaining this clearance will allow the lock to deliver optimum
performance. The container should be constructed to prevent access to the key lock without the use of tools when the container door or drawer is left open. Make sure the lock is not installed in a manner
that will allow objects to come in contact with the changing button.
Handing: The lock is designed to be mounted right-hand, left-hand, vertical-up, and vertical-down only.
Note: Every installation of this product must comply with these requirements and those in the product installation instructions to qualify for the manufacturer’s warranty and to comply
with EN1300 requirements.
Dimensions: Sargent & Greenleaf / FAS 6860, 6870, 6880, 6890
(inches)
[millimeters]
Copyright© 2016, Sargent & Greenleaf, Inc.
TUBE RECESS PATTERN
SAFE DOOR
LOCK BODY
LOCK BOLT
GUIDE
TUBE
ESCUTCHEON
www.sargentgreenleaf.com
Sargent & Greenleaf, Inc.
PO Box 930
Nicholasville, KY 40356
Phone: [phone] Fax: [phone]
Phone: [phone] Fax: [phone]
Sargent & Greenleaf S.A.
9, Chemin du Croset
1024 Ecublens, Switzerland
Phone: [phone]
Fax: [phone]