Satel AQUA RING S User manual

Digital passive infrared detector
for ceiling mount installation
AQUA RING S
Firmware version 4.00
aquaring_s_en 07/23
SATEL sp. z o.o. • ul. Budowlanych 66 • 80-298 Gdańsk • POLAND
tel. [phone]
www.satel.pl
EN

IMPORTANT
The device should be installed by qualified personnel.
Prior to installation, please read carefully this manual.
Changes, modifications or repairs not authorized by the manufacturer shall void your rights
under the warranty.
SATEL aims to continually improve the quality of its products, which may result in changes in
their technical specifications and software. Current information about the changes being
introduced is available on our website.
Please visit us at:
https://support.satel.pl
The declaration of conformity may be consulted at www.satel.pl/ce
The following symbols may be used in this manual:
- note,
- caution.

CONTENTS
1. Features ...........................................................................................................................2
2. Specifications ...................................................................................................................2
3. Description........................................................................................................................3
Supply voltage control ......................................................................................................3
LED indicator....................................................................................................................3
4. Electronics board..............................................................................................................3
Terminals..........................................................................................................................4
5. Selecting a mounting location...........................................................................................4
6. Installation ........................................................................................................................4
7. Start-up and walk test.......................................................................................................7

2 AQUA Ring S SATEL
The AQUA Ring S detector detects motion in the protected area. This manual applies to the
detector with electronics version 4.2.
1. Features
•Motion detection with passive infrared sensor (PIR).
•Selectable detection sensitivity.
•Digital motion detection algorithm.
•Digital temperature compensation.
•Built-in end-of-line resistors (2EOL: 2 x 1.1 k).
•LED indicator.
•Supervision of supply voltage.
•Tamper protection against enclosure opening.
2. Specifications
Power supply ..............................................................................12...24 VAC/DC -10% / +15%
Standby current consumption:
AC power..............................................................................................................11.5 mA
DC power.................................................................................................................. 5 mA
Maximum current consumption
AC power..............................................................................................................12.5 mA
DC power.................................................................................................................. 6 mA
EOL resistors.............................................................................................................2 x 1.1 k
Outputs
alarm (NC relay, resistive load) .........................................................40 mA / 27 VAC/DC
tamper (NC).....................................................................................100 mA / 30 VAC/DC
Relay contact resistance....................................................................................................26 Ω
Alarm signaling period...........................................................................................................2 s
Detectable speed......................................................................................................0.3...3 m/s
Warm-up period..................................................................................................................30 s
Recommended installation height.............................................................................2.2...4.5 m
Protected area:
mounting at a height of 2.4 m...................................................................................36 m2
mounting at a height of 3.7 m...................................................................................80 m2
Complied with standards...............................................EN 50130-5, EN 50131-1, EN 50130-4
Environmental class according to EN 50130-5 ........................................................................II
Operating temperature range...............................................................................-10°C...+55°C
Maximum humidity..........................................................................................................93
±
3%
Dimensions...........................................................................................................ø97 x 29 mm
Weight.................................................................................................................................57 g

SATEL AQUA Ring S 3
3. Description
The alarm output will turn on for 2 seconds when the infrared sensor (PIR) detects motion.
Supply voltage control
When the voltage drops below 9 V (± 5%) for more than 2 seconds, the detector will indicate
a trouble. The trouble is indicated by the alarm output and the LED turning on. Signaling will
continue as long as the trouble exists.
LED indicator
The LED indicates:
•warm-up –blinking rapidly for 30 seconds,
•alarm –ON for 2 seconds,
•trouble (low supply voltage) –ON for entire duration of the trouble.
4. Electronics board
Do not touch the pyroelectric sensor, so as not to soil it.
red LED indicator.
pins for configuration of the detector outputs. Available settings are shown in the figures:
2 –built-in resistors are used –connect the detector outputs as shown in Fig. 10.
3 –built-in resistors are not used –connect the detector outputs as shown in Fig. 11.
tamper switch (NC).
PIR sensor (quad element pyrosensor).
fixing screw hole.
detector configuration pins:
PIR SENS. –selecting the PIR sensor detection sensitivity –see: Fig. 4 (A –low
sensitivity, B and C –medium sensitivity, D –high sensitivity)
LED ON/OFF –enabling/disabling the LED (jumper on –LED enabled; jumper off –
LED disabled).

4 AQUA Ring S SATEL
Terminals
NC - alarm output (NC relay).
TMP - tamper output (NC).
24V - 12...24 VAC/DC power input.
5. Selecting a mounting location
•Do not install the detector outdoors (A).
•Install the detector at the recommended height (B).
•Do not point the detector towards fans (C), air conditioners (D) or heat sources (E).
6. Installation
Disconnect power before making any electrical connections.
The detector is designed for indoor installation.
1. Open the enclosure (Fig. 5).
2. Remove the electronics board (Fig. 6).
3. Make the openings for screws (Fig. 7) and cable (Fig. 8) in the enclosure base.
4. Pass the cable through the prepared opening.
5. Use wall plugs (anchors) and screws to secure the enclosure base to the ceiling. The wall
plugs (anchors) delivered with the device are intended for concrete, brick, etc. For other
types of surface (drywall, styrofoam), use the appropriately selected wall plugs.
6. Fasten the electronics board.

SATEL AQUA Ring S 5
7. Connect the wires to the corresponding terminals.
8. Configure the detector settings.
9. Replace the cover. The marks on the cover and base will help you close the enclosure
(Fig. 9).

6 AQUA Ring S SATEL

SATEL AQUA Ring S 7
7. Start-up and walk test
The LED indicator should be enabled during the walk test.
1. Power on the detector. The LED will be flashing for 30 seconds to indicate warm-up of the
detector.
2. When the LED stops flashing, check if moving within the detector coverage area will make
the LED to light up.
3. If needed, readjust the sensitivity (Fig. 4) and check the detector operation.