Satel SPL-2030-R User manual

®
OPTICAL-ACOUSTIC
SIGNALING DEVICE
SPL-2030
spl2030_en 09/08
The SPL-2030 op ical-acous ic signaling device (siren) is designed for applica ion in he
burglary and assaul signaling sys ems. The signaling func ion is performed in wo ways:
visually (by blinking of indica or LEDs si ua ed in he lower par of he enclosure) and
acous ically (by a modula ed high-volume sound signal). As he ligh source, a se of LEDs is
used, whereas he sound signal is genera ed by means of a piezoelec ric ransducer. Design
of he signaling device housing ensures a high degree of amper pro ec ion (agains opening
and/or earing off from he base). The elec ronic circui is made by he use of SMD echnique
and impregna ed agains he adverse influence of wea her condi ions, which ensures a high
reliabili y of he device. As he SPL-2030 ex ernal housing is made of he PC LEXAN
high-impac polycarbona e, i is charac erized by a very high mechanical s reng h, and a nice
appearance of he device is guaran eed even af er many years of service.
1. Outfit options
The siren can be fi ed wi h addi ional elemen s of amper pro ec ion (sold separa ely),
including:
• inner cover of galvanized me al shee , OM-SPL2000,
• foam de ec or, SPL-SAB or SPL-TO.
In order o ins all he SPL-SAB de ec or, remove he elec ronics board and unsolder he SMD
componen (si ua ed undernea h he board), designed for shor ing he solder poin s J3
and J4. Nex , solder he de ec or leads o hese poin s and, using a screw, a ach
he de ec or o he siren base (so as o cover he opening) and remoun he PCB.
2. Installing
The SPL-2030 siren should be moun ed on fla ver ical surface in inaccessible place in order
o minimize ampering possibili y. I mus be a ached o he surface by means of screws and
expansion plugs ( he screws and expansion plugs are included in he device delivery se ).
Note: Make sure to leave a distance of about 4.5 cm between the upper edge of the
signaling device base and the ceiling or another object which limits the mounting
position from above. With no gap, mounting of the signaling device external housing
may be difficult.
Explana ions for Figure 1:
1 – moun ing holes
2 – auxiliary opening
3 – foam de ec or (op ion)
4 – buzzer
5 – cable hole
6 – amper elemen “S” (should be screwed o he moun ing surface; do no apply excessive
force, so as no o break he narrowings)
7 – wa er drain holes (make sure hey are no s opped)

2 SATEL SPL-2030
Fig. 1. View of he SPL-2030 siren enclosure
Af er moun ing he siren i is recommended o seal he moun ing holes, auxiliary opening, and
cable en ry hole wi h silicon rubber pas e.
3. Connections
The SPL-2030 signaling device can be used wi h any equipmen which sends 12V DC on
ou pu o ac iva e signaling. Connec ing +12 V power supply o he "+ SA –" erminals will
rigger he acous ic signaling, and o he "+ SO –" erminals - he op ical signaling in
he SPL-2030 device.
The amper circui of he siren will be open on removing he ou er enclosure, covering wi h
moun ing foam, or de aching he siren from he wall. For he amper con ac o func ion
correc ly during pull-off, he "S" elemen mus be screwed o he moun ing surface
(see Fig. 1).
Connec ors "TMP" are designed for connec ing in o amper circui of securi y sys em.
By placing jumpers on he P1– P5 pins, you can selec one of he hree audible signals for
alarm signaling.
JP2
JP1
JP4
JP3
JP5
MEL1=JP1+JP4
JP2
JP1
JP4
JP3
JP5
MEL3=JP3+JP5
JP2
JP1
JP4
JP3
JP5
MEL2=JP2+JP5
Fig. 2. The manner of placing jumpers o ob ain he required signaling one.
– pins shor ed
– pins open

SPL-2030 SATEL 3
INTEGRA 32
SPL-2030
SO TMPSA
++
OUT1 COMCOM COM Z1 OUT2
COM OUT1 COM COM COM COMOUT2 +KPD DTM CKM +EX CK AUX Z1
DT
R
Fig. 3. Connec ing he SPL-2030 siren o high-curren ou pu s of INTEGRA 32
con rol panel. The OUT1 ou pu will release op ical signaling, and he OUT2
ou pu - acous ic (high-curren ou pu s wi h normal polariza ion - ac iva ed when +12 V
vol age is supplied). The Z1 zone is programmed as 24 h amper.
I is possible o con rol wo ypes of signaling from one ou pu of con rol panel, by connec ing
in parallel he erminals +SA o +SO and -SA o -SO.
Note: ome control panels may require connecting a resistor R (approx. 1 kΩ) between
the +SA- terminals in the siren. If this resistor is not connected, the siren may emit
some low sounds when not alarming.
Descrip ion of he erminals:
+SO- – op ical signaling erminals
+SA- – acous ic signaling erminals
TMP – amper circui erminals

4 SATEL SPL-2030
SPL-2030
P2
INTEGRA 32
P1
AUX Z1 COMCOM CK
COM Z2
CKM +EX DT+KPD DTM
OUT2
OUT3
OUT4
OUT5
OUT6
OUT7
OUT8
SO TMPSA
++
Fig. 4. Connec ing he SPL-2030 siren o low-curren ou pu s of INTEGRA 32 con rol
panel. The OUT2 ou pu has been programmed as power ou pu . The OUT3 ou pu
con rols he P1 relay, which releases acous ic signaling, and he OUT4 ou pu con rols
he P2 relay, which releases op ical signaling (low-curren ou pu s wi h normal
polariza ion - ac iva ed by shor ing he erminal direc ly o he common ground 0 V).
The Z2 zone is programmed as 24 h amper.
4. Technical data
Nominal power supply ........................................................................................ 12 V DC ±20%
Mean curren consump ion when signaling
acous ic signaling ...................................................................................... 250 mA
op ical signaling ..........................................................................................35 mA
Working empera ure range ................................................................................... -35…+60 °C
Sound pressure .................................................................................................. approx. 120 dB
Enclosure dimensions ...................................................................................... 298x197x90mm
Weigh ............................................................................................................................... 725 g
SATEL sp. z o.o.
ul. Schuber a 79
80-172 Gdańsk
POLAND
el. ([phone]
info@sa el.pl
www.sa el.pl
La es EC declara ion of conformi y and
produc approval cer ifica es can be
downloaded from our web si e www.satel.pl