Sauder Cannery Bridge 415910 User manual

Need help? Visit Sauder.com to view video assembly tips or chat with a live rep.
Prefer the phone? Call 1-800-523-3987.
Share your journey!
sauder.com
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
English pg 1-26
Français pg 27-29
Español pg 30-32
Lot # 373062 05/22/15
Purchased: __________________
Be sure to give us a ring before
making any returns. 1-800-523-3987
Work Table
Cannery Bridge Collection | 415910
The original desktop.

Table of Contents Assembly Tools Required
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Hammer
Not actual size
Skip the power trip.
This time.
A2 RIGHT END (1)
B LEFT END (1)
C OUTER END (1)
D TOP (1)
E BOTTOM (1)
F BACK (1)
G BRACE (1)
H STRETCHER (1)
I DOOR (1)
J2 RIGHT FRONT LEG (1)
K2 LEFT FRONT LEG (1)
L2 RIGHT REAR LEG (1)
M2 LEFT REAR LEG (1)
N OUTER LEG (6)
O2 FRONT LEG (1)
P2 REAR LEG (1)
Q BASE (1)
R VALANCE (2)
S DRAWER FRONT (1)
T RIGHT END MOLDING (1)
U LEFT END MOLDING (1)
V BACK MOLDING (1)
D132 RIGHT DRAWER SIDE (1)
D138 LEFT DRAWER SIDE (1)
D159 DRAWER BACK (1)
D969 DRAWER BOTTOM (1)
2-3
4
5-26
27-29
30-32
33-34
35
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Part Identification Now you know
our ABCs.
415910 www.sauder.com/servicesPage 2
Tape Measure

Part Identification
415910www.sauder.com/services Page 3
D132
D138
D159
D969
A2
B
C
D
E
F
G
H
I
J2
K2
L2
M2
N
O2
P2
Q
R
S
T
U
V
R
N
N
N
N
N

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
415910 www.sauder.com/servicesPage 4
40CA CABINET RIGHT - 1 40CB CABINET LEFT - 1 40CC DRAWER RIGHT - 1 40CD DRAWER LEFT - 1
I-BEAM - 42
56M
TIE PLATE - 1
3G
BLACK 9/16" LARGE HEAD SCREW - 2
1S
BLACK 7/8" MACHINE SCREW - 4
37S
3S GOLD 5/16" FLAT HEAD SCREW - 8
10A SLIDE CAM - 2
BLACK 1/2" FLAT HEAD SCREW - 4
11S
BLACK 9/16" FLAT HEAD SCREW - 6
32S
CAM SCREW - 8
8F
14H HINGE - 2 DOOR STOP - 1 4I
WOOD DOWEL -1
15F
HIDDEN CAM - 22
1F CAM DOWEL - 14 2F
GLUE - 1
54M
KNOB - 4
95K
BLACK 1-15/16" FLAT HEAD SCREW - 19
113S
30S BLACK 1-9/16" FLAT HEAD SCREW - 4

Step 1 Look for this icon. It means a
video assembly tip is available at
www.sauder.com/services/tips
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å Push twenty-two HIDDEN CAMS (1F) into the ENDS (A2, B,
and C), BOTTOM (E), BACK (F), and VALANCES (R). Then,
insert the metal end of a CAM DOWEL (2F) into each
HIDDEN CAM except for the short edges of the
VALANCES (R) and the BACK (F).
415910www.sauder.com/services Page 5
Arrow
1F
2F
(14 used)
Insert the metal end of the CAM
DOWEL into the HIDDEN CAM.
Arrow
Do not tighten the HIDDEN CAMS in this step.
Do not insert CAM DOWELS into these edges.
Arrow
The arrow in the HIDDEN CAM
must point toward the hole in
the edge of the board.
Hole
1F
Arrow
Arrow
1F
(22 used) A2
B
C
E
F
R
R