Sauder Boulevard Cafe 420645 User manual

Need help? Visit Sauder.com to view video assembly tips or chat with a live rep.
Prefer the phone? Call 1-800-445-1527.
Share your journey!
sauder.com
Coee Table
Boulevard Cafe Collection | Model 420645
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
English pg 1-19
Français pg 20-22
Español pg 23-25
Lot #: 510022
Date Purchased: __________________
10/26/17
Be sure to give us a ring before
making any returns. 1-800-445-1527
It's addicting.

Table of Contents Assembly Tools Required
3
4
5-19
20-22
23-25
26
27
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Skip the power trip.
This time.
Page 2 www.sauder.com 420645

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
A RIGHT END (1)
B LEFT END (1)
C UPRIGHT (1)
D TOP (1)
E BOTTOM (1)
F BACK (2)
G SLIDING DOOR (1)
H DRAWER FRONT (2)
I RIGHT DRAWER SIDE (2)
J LEFT DRAWER SIDE (2)
K DRAWER BACK (2)
L DRAWER BOTTOM (2)
M DRAWER BRACE (2)
Now you know
our ABCs.
Page 3www.sauder.com420645
A
B
C
D
E
F
G
H
I
K
M
L
F
J
H
I
K
M
L
J

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
Page 4 www.sauder.com 420645
(EXTENSION SET SHOWN SEPARATED)
ANGLED HEAD
CAM SCREW - 12
4
Angled head
LARGE HIDDEN
CAM - 14
3
WOOD
DOWEL - 30
8
LONG WOOD
DOWEL - 2
7
APPLIQUE CARD - 1
14
SMALL HIDDEN
CAM - 12
5STRAIGHT HEAD
CAM SCREW - 12
6
Straight head
EXTENSION RAIL - 4
1EXTENSION SLIDE - 4 2
BLACK 1-1/2" FLAT HEAD SCREW - 22
15
DOUBLE DOWEL - 1
9
BLACK 1/2" MACHINE HEAD SCREW - 4
17
BLACK 1/2" WAFER HEAD SCREW - 16
16
BLACK 1/2" PAN HEAD SCREW - 24
18
LONG PULL - 1
12 PULL - 2 13
CASTER - 2
11
LOCKING CASTER - 2
10
BLACK 3/8" MACHINE HEAD SCREW - 2
19

Step 1 Look for this icon. It means a
video assembly tip is available at
www.sauder.com/services/tips
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å Before beginning this step, separate the LARGE HIDDEN
CAMS (3) from the SMALL HIDDEN CAMS (5). Do not
confuse these HIDDEN CAMS.
å Push fourteen LARGE HIDDEN CAMS (3) into the ENDS (A
and B), UPRIGHT (C), and BACKS (F).
Page 5www.sauder.com420645
3
Arrow
Arrow
(14 used)
3
A
C
F
B
F
The arrow in the HIDDEN
CAM must point toward the
hole in the edge of the board.
Hole
Arrow

Step 2
å Separate the EXTENSION SLIDES (2) from the EXTENSION RAILS (1) as shown in the enlarged diagram
below. Be prepared, the parts are greasy.
å Fasten the EXTENSION RAILS (1) to the RIGHT END (A) and UPRIGHT (C). Use twelve BLACK 1/2" PAN
HEAD SCREWS (18).
å NOTE: For each EXTENSION RAIL, turn a SCREW into the hole shown in the enlarged diagram. Then, slide
the inner cartridge of the EXTENSION RAIL in to find the other holes that line up with the holes in the END
and UPRIGHT. Turn a SCREW into these holes.
å NOTE: The EXTENSION SLIDES will be used later for the DRAWERS.
Page 6 www.sauder.com 420645
A
C
Push the black lever up and
pull the SLIDE from the RAIL.
1
1
2
Use these holes.Open end
BLACK 1/2" PAN HEAD SCREW
(12 used in this step)
18
1
1
1
Open end
Open end
This HIDDEN CAM
must be here.
These holes are
closer to this edge.

Step
Page 7www.sauder.com420645
Step 3
A
B
D
å Before beginning this step, separate the ANGLED HEAD
CAM SCREWS (4) from the STRAIGHT HEAD CAM
SCREWS (6). Do not confuse these CAM SCREWS.
å Turn twelve ANGLED HEAD CAM SCREWS (4)
into the ENDS (A and B) and TOP (D).
å NOTE: Use the exact holes shown.
Angled head
(12 used)
4

StepStep 4
å Insert thirteen WOOD DOWELS (8) into the TOP (D).
D
(13 used) 8
Page 8 www.sauder.com 420645

å Insert the LONG WOOD DOWELS (7) and DOUBLE
DOWEL (9) into the end of one of the BACKS (F) as shown.
Tighten the HIDDEN CAM to secure the DOUBLE DOWEL
into the BACK.
å Slide the UPRIGHT (C) over the LONG WOOD DOWELS
and DOUBLE DOWEL in the BACK (F).
å Fasten the remaining BACK (F) to the UPRIGHT (C). Tighten
one HIDDEN CAM.
å NOTE: Be sure the LONG WOOD DOWELS insert into
the BACK.
Step 5
1
2
1st
3rd
2nd
C
CF
F
Surface with
HIDDEN CAMS
Edge without
HIDDEN CAMS
9
7
7
F
Surface with
HIDDEN CAMS
F
Surface with
HIDDEN CAMS
Edge without
HIDDEN CAMS
Edge without
HIDDEN CAMS
1
1
Page 9www.sauder.com420645
Tighten the HIDDEN
CAM onto the
DOUBLE DOWEL.

Step 6
Page 10 www.sauder.com 420645
å Insert four WOOD DOWELS (8) into the ENDS (A and B).
å Fasten the ENDS (A and B) to the BACKS (F). Tighten two
HIDDEN CAMS.
å NOTE: Be sure the WOOD DOWELS in the ENDS insert
into the BACKS.
A
B
F
8
Edge without
HIDDEN CAMS
Surface with
HIDDEN CAMS
Edge without
HIDDEN CAMS
Edge without
HIDDEN CAMS
F
Surface with
HIDDEN CAMS
8