Sauder North Avenue 426016 User manual

sauder.com
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
sauder.com
CONTACT US FIRST
BEFORE MAKING ANY RETURNS TO THE STORE.
sauder.com
CONTACT US FIRST
BEFORE MAKING ANY RETURNS TO THE RETAILER.
Visit sauder.com/service to order replacement parts, view video assembly tips, or chat with a live rep.
Prefer the phone? Give us a ring at 1-800-445-1527.
Customer Service is available Monday-Friday - 9 a.m. to 5:30 p.m. EST (except holidays)
Sauder.com
Share your journey!
English pg 1-14
Français pg 15-17
Español pg 18-20
Lot # 559464 01/20/21
Purchased: __________________
TV Stand With Mount
North Avenue Collection | Model 426016
Your holder for all
things awesome.

Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
No. 2 Phillips Screwdriver
Tip Shown Actual Size
WARNING
!
Table of Contents Assembly Tools Required
3
4
5-14
15-17
18-20
21-22
23
Use of a TV that is too heavy or large is hazardous. A TV that is too heavy will create a risk of a tip-over that can cause severe injury or
death. A TV that is too large for the available space might be accidentally pushed or bumped o the furniture, or subject to tip-over.
• Check the size and weight of your TV. Compare it to the diagram below – before you begin assembly!
• This Sauder unit is designed for use with flat panel televisions weighing less than 70 pounds. Never use with a TV that weighs more.
• The size of the television, front-to-back and side-to-side, must fit within the space defined in the diagram.
• Never place the front edge of the TV past the front edge of the TV support shelf (or stop molding – if equipped)
• Never allow the sides of the TV to extend past the side edges of the TV support surface.
• Be sure to apply the warning label as instructed later in the assembly. The label provides important safety related information.
70 lbs.70 lbs.
15-5/8"15-5/8"
43-3/8"43-3/8"
Page 2 www.sauder.com/service 426016

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
A END (2)
B FRONT BRACE (2)
C BACK BRACE (2)
E TOP (1)
F BOTTOM (1)
L SUPPORT BRACKET (1)
M VERTICAL RAIL (2)
N POST (1)
A
A
B
B
C
C
E
F
M
M
Page 3www.sauder.com/service426016
L
Found in
TV METAL
PARTS KIT
N

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
9/16" PAN HEAD SCREW - 2
8
CORD CLIP - 2
3
BARREL NUT - 4
2
1/2" HEX HEAD SCREW - 4
61-3/16" HEX HEAD SCREW - 24 7
L-WRENCH - 2
4
(Refer to the last step for proper location and application)
WARNING LABEL - 1
5
522,68 22,68
70 lbs. 31,75 kg 31,75 kg
Page 4 www.sauder.com/service 426016
TV METAL PARTS KIT
Not all hardware will be used.
SPACER - 4
20 WASHER - 12 21
1-9/16" BOLT- 4
22 1-3/8" BOLT- 4 23
1/2" LARGE BOLT- 4
25 1/2" SMALL BOLT- 4 26
13/16" BOLT - 2
24
LARGE WASHER - 2
19

Step 1
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å Fasten the BRACES (B and C) to a END (A). Tighten four
1-3/16" HEX HEAD SCREWS (7) using the L-WRENCH (4).
å NOTE: You should start each SCREW a few turns before
completely tightening any of them.
A
B
B
C
C
4
1-3/16" HEX HEAD SCREW
(4 used in this step)
7
These holes must be here.
Straight edge
Page 5www.sauder.com/service426016
Just think. The sooner
you do this, the sooner
you do something else.

å Fasten the remaining END (A) to the BRACES (B and C).
Tighten four 1-3/16" HEX HEAD SCREWS (7) using
the L-WRENCH (4).
å NOTE: You should start each SCREW a few turns before
completely tightening any of them.
Step 2
A
B
B
C
C
41-3/16" HEX HEAD SCREW
(4 used in this step)
7
Straight edge
Page 6 www.sauder.com/service 426016

å Fasten the BRACES (B and C) to the TOP (E). Tighten six
1-3/16" HEX HEAD SCREWS (7) using the L-WRENCH (4).
å NOTE: You should start each SCREW a few turns before
completely tightening any of them.
Step 3
B
C
E
41-3/16" HEX HEAD SCREW
(6 used in this step)
7
Holes closest to this edge.
Page 7www.sauder.com/service426016

å Carefully turn your unit onto its back edges.
å Fasten the BOTTOM (F) to the BRACES (B and C).
Tighten six 1-3/16" HEX HEAD SCREWS (7) using
the L-WRENCH (4).
å NOTE: You should start each SCREW a few turns before
completely tightening any of them.
Step 4
F
B
C
41-3/16" HEX HEAD SCREW
(6 used in this step)
7
Page 8 www.sauder.com/service 426016
Now might be a
good time to refresh
your drink.

å Carefully stand your unit upright.
å Fasten the POST (N) and LARGE WASHERS (19) to the
BACK BRACES (C). Tighten four 1-3/16" HEX HEAD
SCREWS (7) using the L-WRENCH (4).
å NOTE: You should start each SCREW a few turns before
completely tightening any of them.
Step 5
C
C
N
4
1-3/16" HEX HEAD SCREW
(4 used in this step)
7
Page 9www.sauder.com/service426016
19

å Fasten the CORD CLIPS (3) to the POST (N). Use two
9/16" PAN HEAD SCREWS (8).
Step 6
N
9/16" PAN HEAD SCREW
(2 used in this step)
8
3
Page 10 www.sauder.com/service 426016