Sauder Trestle 416955 User manual

Need help? Visit Sauder.com to view video assembly tips or chat with a live rep.
Prefer the phone? Call 1-800-523-3987.
Share your journey!
sauder.com
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
English pg 1-22
Français pg 23-25
Español pg 26-28
Lot # 361021 05/13/14
Purchased: __________________
Be sure to give us a ring before
making any returns. 1-800-523-3987
Anywhere Console
Trestle Collection | Model 416955
Your holder for all
things awesome.

Table of Contents Assembly Tools Required
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Skip the power trip.
This time.
3
4
5-22
23-25
26-28
29-30
31
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
WARNING
!
Use of a TV that is too heavy or large is hazardous. A TV that is too heavy will create a risk of a tip-over that can cause severe injury or
death. A TV that is too large for the available space might be accidentally pushed or bumped o the furniture, or subject to tip-over.
• Check the size and weight of your TV. Compare it to the diagram below – before you begin assembly!
• This Sauder unit is designed for use with televisions weighing less than 70 pounds. Never use with a TV that weighs more.
• The size of the television, front-to-back and side-to-side, must fit within the space defined in the diagram.
• Never place the front edge of the TV past the front edge of the TV support shelf (or stop molding – if equipped)
• Never allow the sides of the TV to extend past the side edges of the TV support surface.
• If the TV has a CRT picture tube, the picture tube cone may extend past the rear of the support shelf.
• Be sure to apply the warning label as instructed in the last assembly step. The label provides important safety related information.
70 lbs.
70 lbs.
16-1/2"
16-1/2"
45-3/8"
45-3/8"
416955 www.sauder.com/servicesPage 2
Short Screwdriver
(provided)

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
A RIGHT END (1)
B LEFT END (1)
C UPRIGHT (1)
D SMALL UPRIGHT (1)
E TOP (1)
F BOTTOM (1)
G SHELF (2)
H LOWER SHELF (1)
I BACK (1)
J SMALL BACK (2)
K RIGHT FRONT LEG (1)
L LEFT FRONT LEG (1)
M RIGHT REAR LEG (1)
N LEFT REAR LEG (1)
O SKIRT (2)
P BOTTOM SIDE SKIRT (2)
Q TOP SIDE SKIRT (2)
R LEFT DRAWER FRONT (1)
S RIGHT DRAWER FRONT (1)
T SHELF MOLDING (1)
D75 DRAWER BACK (2)
D83 RIGHT DRAWER SIDE (2)
D84 LEFT DRAWER SIDE (2)
D721 DRAWER BOTTOM (2)
416955www.sauder.com/services Page 3
A
B
C
D
E
F
G
H
I
JK
L
M
N
O
P
Q
R
S
T
G
J
P
Q
O
D75
D721
D721
D75
D83
D83
D84
D84

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
416955 www.sauder.com/servicesPage 4
3M ANTI-SKID PAD - 1
(Refer to step 17 for proper
location and application)
WARNING LABEL - 1
2L
WARNING
Never use this furniture with a TV that is too
large or too heavy. Severe injury or death
can occur.The TV and furniture will be
unstable and may tip.
-The TV must less than 70 lbs.
-The base of the TV must be able to sit
completely on this shelf.
-Refer to instruction book for complete
safety information.
Note: This is a permanent label. Do not try
to remove. Surface will be damaged.
02/ 02 269224
35GA CABINET RIGHT - 2 35GB CABINET LEFT - 2 35GC DRAWER RIGHT - 2 35GD DRAWER LEFT - 2
SILVER 1/2" MACHINE SCREW - 4
38S
BLACK 9/16" LARGE HEAD SCREW - 16
1S
ANGLE BRACKET - 8
5G
SILVER 1-1/8" FLAT HEAD SCREW - 18
10S
LONG METAL PIN - 2
3R
BLACK 1-7/8" FLAT HEAD SCREW - 8
2S
CAM COVER - 15
12P SCREW COVER - 12 20P
3S GOLD 5/16" FLAT HEAD SCREW - 16
METAL PIN - 4
1R
10A SLIDE CAM - 4 CAM SCREW - 8 8F
NAIL - 30
1N
30S BLACK 1-9/16" FLAT HEAD SCREW - 8
HIDDEN CAM - 20
1F CAM DOWEL - 12 2F
PULL - 2
81K

Step 1 Look for this icon. It means a
video assembly tip is available at
www.sauder.com/services/tips
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å Push twenty HIDDEN CAMS (1F) into the UPRIGHTS (C
and D), BOTTOM (F), SHELVES (G and H), SMALL
BACKS (J), and TOP SIDE SKIRTS (Q). Then, insert the
metal end of a CAM DOWEL (2F) into each HIDDEN
CAM except for the CAMS in the BOTTOM (F) and
LOWER SHELF (H).
416955www.sauder.com/services Page 5
Arrow
Do not tighten the HIDDEN CAMS in this step.
Do not insert CAM DOWELS into these parts
The arrow in the HIDDEN
CAM must point toward the
hole in the edge of the board.
Hole
Arrow
Insert the metal end of the CAM
DOWEL into the HIDDEN CAM.
Arrow
1F
2F
(12 used)
(20 used)
C
D
F
G
H
J
Q
Q
J
G
Scan this QR code or go to this address:
http://qr.sauder.com/?ID=1526
to watch a video on how to assemble your unit.

å Turn eight CAM SCREWS (8F) into the LEGS (K, L, M, and N).
å NOTE: Be sure to use the exact holes shown in the LEGS.
å Fasten the TOP SIDE SKIRTS (Q) to the LEGS (K, L, M, and N).
Use eight SILVER 1-1/8" FLAT HEAD SCREWS (10S).
Step 2
416955 www.sauder.com/servicesPage 6
Remember:
Righty tighty.
Lefty loosey.
K
L
M
N
Q
Q
Surface with
HIDDEN CAMS
Surface with
HIDDEN CAMS
Edge with
HIDDEN CAMS
SILVER 1-1/8" FLAT HEAD SCREW
(8 used in this step)
10S
8F (8 used)
K
L
M
N

å Fasten the ENDS (A and B) to the LEGS (K, L, M, and N).
Use six SILVER 1-1/8" FLAT HEAD SCREWS (10S).
Step 3
416955www.sauder.com/services Page 7
K
L
M
N
Surface with
more holes Surface with
more holes
A
B
SILVER 1-1/8" FLAT HEAD SCREW
(6 used in this step)
10S

Step 4
416955 www.sauder.com/servicesPage 8
å Fasten the CABINET RIGHTS (35GA) to the RIGHT END (A) and
SMALL UPRIGHT (D) and the CABINET LEFTS (35GB) to the
LEFT END (B) and other surface of the SMALL UPRIGHT (D).
Use four GOLD 5/16" FLAT HEAD SCREWS (3S) through
holes #1 and #3.
å NOTE: Be sure to fasten the CABINET RIGHT and CABINET
LEFT to the SMALL UPRIGHT (D) exactly as shown.
1
2
3
1
2
3
Roller end
Roller end
K
L
A
B
1
2
3
1
2
3
Surface with
HIDDEN CAM
D
Roller end
GOLD 5/16" FLAT HEAD SCREW
(8 used in this step)
3S

å Fasten the TOP SIDE SKIRT (Q) on the LEFT END (B)
assembly to the TOP (E). Tighten two HIDDEN CAMS.
Step 5
416955www.sauder.com/services Page 9
Start Tighten
Arrow
Minimum
190 degrees
Caution
Risk of damage or
injury. HIDDEN CAMS
must be completely
tightened. HIDDEN
CAMS that are not
completely tightened
may loosen, and parts
may separate. To
completely tighten:
Arrow
Maximum
210 degrees
B
LQ
E
Surface with holes
These holes must be here.
Do not stand the unit upright without the
BACK fastened. The unit may collapse.
Caution

å Fasten the SMALL BACKS (J) to the TOP (E). Tighten two
HIDDEN CAMS.
Step 6
416955 www.sauder.com/servicesPage 10
Arrow
Minimum
190 degrees
Maximum
210 degrees
E
J
J
Surface
with
HIDDEN
CAM
Surface
with
HIDDEN
CAM