Sauder Dakota Pass Armoire 419077 User manual

Need help? Visit Sauder.com to view video assembly tips or chat with a live rep.
Prefer the phone? Call 1-800-523-3987.
Share your journey!
sauder.com
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
Enlish p 1-28
Français p 29-32
Español p 33-36
Lot # 376556 09/28/15
Purchased: __________________
Be sure to ive us a rin before
makin any returns. 1-800-523-3987
Armoire
Dakota Pass Collection | 419077
You could use a new
hide-and-seek spot.

Table of Contents Assembly Tools Required
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Skip the power trip.
This time.
A RIGHT END (1)
B LEFT END (1)
C TOP (1)
D BOTTOM (1)
E SHELF (1)
F BACK (1)
G DOOR (2)
H ADJUSTABLE SHELF (1)
I RIGHT FRONT LEG (1)
J LEFT FRONT LEG (1)
K BACK LEG (2)
L DRAWER FRONT (1)
M TOP MOLDING (1)
N SHELF MOLDING (1)
O BOTTOM MOLDING (1)
P DOOR MOLDING (2)
Q DRAWER FRONT MOLDING (1)
D30 RIGHT DRAWER SIDE (1)
D31 LEFT DRAWER SIDE (1)
D80 DRAWER BACK (1)
D985 DRAWER BOTTOM (1)
M67 DRAWER BRACE (1)
2-3
4-5
6-28
29-32
33-36
37-38
39
419077 www.sauder.com/servicesPae 2
Part Identification Now you know
our ABCs.
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the ede
to help distinuish similar parts from each other. Use this part identification to help identify similar parts.

Part Identification
419077www.sauder.com/services Pae 3
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
D30
D31
M67
D80
D985
K
P
G

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
419077 www.sauder.com/servicesPae 4
ROD - 1
5A
5L WARNING LABEL - 1
(Refer to step 22 for proper
location and application)
WARNING
Serious or fatal crushing injuries can occur
from furniture tip-over. To help prevent
tip-over:
• Place heaviest items in the lowest drawers.
• Unless specifically desined to accommodate, do not
set TVs or other heavy objects on top of this product.
• Never allow children to climb or han on drawers,
doors, or shelves.
• Never open more than one drawer at a time.
• If equipped with a drawer interlock system, do not
defeat or remove it.
Use of tip-over restraints may only reduce, but not
eliminate, the risk of tip-over.
This is a permanent label. Do not attempt to remove!
04/10 332296
SAFETY STRAP - 1
Locate this nylon SAFETY
STRAP (60M) to be used
later in assembly. Do not
accidentally throw away.
60M
SAFETY DRYWALL
ANCHOR - 1
61M
35AA UNIVERSAL
CABINET RAIL - 2 35AC DRAWER RIGHT - 1 35AD DRAWER LEFT - 1
WASHER - 1
13M
7A ROD HANGER - 2
BRACKET - 1
56G
10F TWIST-LOCK®
FASTENER - 12
MOLDING
CONNECTOR - 2
17F
METAL PIN - 4
1R
10A SLIDE CAM - 2 CAM SCREW - 12 8F
WOOD DOWEL - 2
15F
28K KNOB- 4
NAIL - 46
1N
HIDDEN CAM - 12
1F
LARGE RUBBER
SLEEVE - 1
58G
RUBBER SLEEVE - 4
2R
14H HINGE - 4

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
419077www.sauder.com/services Pae 5
GOLD 1" MACHINE SCREW - 2
50S
BLACK 9/16" LARGE HEAD SCREW - 4
1S
BLACK 2-1/4" FLAT HEAD SCREW - 8
26S
3S GOLD 5/16" FLAT HEAD SCREW - 8
BLACK 1/2" FLAT HEAD SCREW - 8
11S
BLACK 1" PAN HEAD SCREW - 9
60S SILVER 1-1/2" MACHINE SCREW - 2 95S
30S BLACK 1-9/16" FLAT HEAD SCREW - 5

Step 1 Look for this icon. It means a
video assembly tip is available at
www.sauder.com/services/tips
419077 www.sauder.com/servicesPae 6
10F
Do not tihten the TWIST-LOCK® FASTENERS in this step.
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratchin your unit or the floor.
å To bein assembly, push twelve SAUDER TWIST-LOCK®
FASTENERS (10F) into the lare holes in the ENDS (A
and B), BOTTOM (D), and SHELF (E).
10F
A
B
D
E

Step 2
419077www.sauder.com/services Pae 7
Arrow
The arrow in the HIDDEN
CAM must point toward the
hole in the ede of the board.
Hole
å Push twelve HIDDEN CAMS (1F) into the ENDS (A
and B), TOP (C), and DRAWER BRACE (M67).
A
B
M67
C
1F
Arrow
Arrow
1F
(12 used)

Step 3
419077 www.sauder.com/servicesPae 8
å Turn twelve CAM SCREWS (8F) into the FRONT LEGS (I
and J), DRAWER FRONT (L), and TOP MOLDING (M).
å Tap two MOLDING CONNECTORS (17F) into the notches
in the TOP MOLDING (M).
8F
Flat end
Flat end
17F
17F
(12 used)
Just think. The sooner
you do this, the sooner
you do somethin else.
I
J
L
M

å Fasten the TOP MOLDING (M) to the TOP (C). Tihten
three HIDDEN CAMS.
å Push the LARGE RUBBER SLEEVE (58G) onto the
BRACKET (56G). The RUBBER SLEEVE will be a tiht fit.
å Fasten the BRACKET (56G) to the TOP MOLDING (M).
Use a BLACK 9/16" LARGE HEAD SCREW (1S).
å NOTE: Be sure to position the BRACKET exactly as shown
in the enlared diaram.
Step 4
419077www.sauder.com/services Pae 9
BLACK 9/16" LARGE HEAD SCREW
(1 used in this step)
1S
M
C
Surface with
HIDDEN CAMS
Short flat ede
1
2
56G
58G

Step 5
419077 www.sauder.com/servicesPae 10
å Fasten the BACK LEGS (K) to the ENDS (A and B). Use
eiht BLACK 2-1/4" FLAT HEAD SCREWS (26S).
å Fasten the ROD HANGERS (7A) to the ENDS (A and B).
Use two BLACK 9/16" LARGE HEAD SCREWS (1S).
7A
(2 used)
BLACK 9/16" LARGE HEAD SCREW
(2 used for the ROD HANGERS)
1S
A
B
Surface with
TWIST-LOCK®
FASTENERS
Surface with
TWIST-LOCK®
FASTENERS
Ede with
HIDDEN CAMS
Ede with
HIDDEN CAMS
K
K
BLACK 2-1/4" FLAT HEAD SCREW
(8 used in this step)
26S
These surfaces
should be even.
Anled ede
These surfaces
should be even.
These surfaces
should be even.

Step 6
419077www.sauder.com/services Pae 11
å Fasten the LEFT END (B) to the TOP (C). Tihten two
TWIST-LOCK® FASTENERS.
Do not stand the unit upriht without the
BACK fastened. The unit may collapse.
Caution
How to use the SAUDER TWIST-LOCK®FASTENER
1. Insert the dowel end of the FASTENER into the
hole of the adjoinin part.
NOTE: The dowel end of the FASTENER must
remain fully inserted in the hole of the adjoinin
part while lockin the FASTENER.
2. Tihten the FASTENER with a Phillips
screwdriver as tiht as possible.
Dowel end
B
Ede with
HIDDEN CAMS
Surface with
TWIST-LOCK®
FASTENERS
C
M
Surface with
HIDDEN CAMS

Step 7
419077 www.sauder.com/servicesPae 12
å NOTE: The BOTTOM (D) is slihtly larer than the
SHELF (E). Do not confuse these parts.
å Fasten the BOTTOM (D) and SHELF (E) to the LEFT
END (B). Tihten four TWIST-LOCK® FASTENERS.
B
E
D
Surface with
TWIST-LOCK®
FASTENERS
Surface with
TWIST-LOCK®
FASTENERS
Notched ede
The BOTTOM (D) is slihtly
larer than the SHELF (E).

Step 8
419077www.sauder.com/services Pae 13
å Slide the SHELF MOLDING* (N) onto the notched ede of
the SHELF (E).
å Slide the BOTTOM MOLDING* (O) onto the notched ede
of the BOTTOM (D).
å *U.S. Patent No. 5,499,886
E
D
Notched ede
O
N
Slide the SHELF MOLDING (N)
onto the notched ede.
Slide the BOTTOM MOLDING (O)
onto the notched ede.

Step 9
419077 www.sauder.com/servicesPae 14
å Fasten the RIGHT END (A) to the TOP (C), BOTTOM (D),
and SHELF (E). Tihten six TWIST-LOCK® FASTENERS.
E
D
C
A
Surface without
TWIST-LOCK®
FASTENERS
Ede with
HIDDEN CAMS
Don't worry. It isn't
Rome. This can be built
in a day.

Step 10
419077www.sauder.com/services Pae 15
å Insert two WOOD DOWELS (15F) into the holes in the
FRONT LEGS (I and J).
å Fasten the FRONT LEGS (I and J) to the ENDS (A
and B). Tihten eiht HIDDEN CAMS.
å NOTE:
Be sure the MOLDING CONNECTORS in the TOP
MOLDING (M) insert into the notches in the FRONT LEGS.
You may need to ently tap them in with your hammer.
å NOTE:
Be sure the WOOD DOWELS in the FRONT LEGS
insert into the holes in the ENDS.
A
B
15F
Anled ede
I
J
M

Step 11
419077 www.sauder.com/servicesPae 16
å Fasten the UNIVERSAL CABINET RAILS* (35AA) to
the ENDS (A and B). Use four GOLD 5/16" FLAT HEAD
SCREWS (3S) throuh holes #1 and #3.
å *patent pendin lide system
1
2
3
A
B
Glide end
1
2
3
Glide end
Glide end
GOLD 5/16" FLAT HEAD SCREW
(4 used in this step)
3S

Step 12
419077www.sauder.com/services Pae 17
å Carefully turn your unit over onto its front edes. Unfold
the BACK (F) and lay it over your unit.
å Make equal marins alon all four edes of the BACK (F).
Push on opposite corners of your unit if needed to make
it "square".
å Fasten the BACK (F) to your unit usin the NAILS (1N).
å NOTE: Be sure to tap NAILS into the holes that line up
over the SHELF (E).
å NOTE: Perforations have been provided for access
throuh the BACK. Carefully cut out the holes needed.
Do not stand the unit upriht without the
BACK fastened. The unit may collapse.
Caution
Unfinished surface
NAIL
(46 used in this step)
1N
F
These holes must line
up over the SHELF (E).
This lare hole
must be here.

å Fasten the DOOR MOLDINGS (P) to the DOORS (G). Use
six BLACK 1" PAN HEAD SCREWS (60S).
Step 13
419077 www.sauder.com/servicesPae 18
P
P
G
G
BLACK 1" PAN HEAD SCREW
(6 used in this step)
60S
Unfinished surface
Unfinished surface
Surface with
more holes
Surface with
more holes

Step 14
419077www.sauder.com/services Pae 19
å Fasten two HINGES (14H) to each DOOR (G). Use eiht
BLACK 1/2" FLAT HEAD SCREWS (11S).
14H
14H
G
G
BLACK 1/2” FLAT HEAD SCREW
(8 used in this step)
11S

Step 15
419077 www.sauder.com/servicesPae 20
Pro Tip: Lift with your
les. And, you know,
your arms.
å Carefully stand your unit upriht.
å Before fastenin the DOOR to your unit, be sure the
mountin screw is aainst the stops as shown in the riht
diaram. If it isn't, loosen the mountin screw to slide it
aainst the stops. Then tihten the mountin screw.
å Fasten a DOOR (G) to the LEFT END (B) as shown in
the lower diaram. Use the screws in the HINGES. You
should start each SCREW a few turns before completely
tihtenin any of them.
å Fasten a KNOB (28K) to the DOOR (G). Use a GOLD 1"
MACHINE SCREW (50S).
å Repeat this step for the other DOOR (G).
å See the next step for DOOR adjustments.
Mountin
screw
Stop
Hine
G
B
28K
GOLD 1" MACHINE SCREW
(2 used in this step)
50S