Sauder County 418529 User manual

Need help? Visit Sauder.com to view video assembly tips or chat with a live rep.
Prefer the phone? Call 1-800-523-3987.
Share your journey!
sauder.com
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
English pg 1-20
Français pg 21-23
Español pg 24-26
Lot # 370342 04/07/15
Purchased: __________________
Be sure to give us a ring before
making any returns. 1-800-523-3987
Mates Bed
County Line Collection | 418529
You won't just fall in
love with it. You'll fall
asleep in it.

Table of Contents Assembly Tools Required
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Skip the power trip.
This time.
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Warranty
2-3
4
5-20
21-23
24-26
27
418529 www.sauder.com/servicesPage 2
Now you know
our ABCs.
Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
A2 BOTTOM (2)
B2 BOTTOM SUPPORT (2)
C UPRIGHT (1)
D DRAWER FRONT (2)
E END (2)
F LOWER FRONT PANEL (1)
G UPPER FRONT PANEL (1)
I BACK PANEL (1)
J2 SMALL SLAT (4)
B30 DRAWER BOTTOM (2)
D212 RIGHT DRAWER SIDE (2)
D213 LEFT DRAWER SIDE (2)
D476 DRAWER BACK (2)
M65 DRAWER BRACE (2)

Part Identification
418529www.sauder.com/services Page 3
A2
A2
B2
B2
C
G
B30
B30
D
D
J2
J2
J2
J2
F
D476
D476
E
E
I
D212
D212 D213
D213
M65
M65

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
418529 www.sauder.com/servicesPage 4
40CB CABINET LEFT - 2 40CA CABINET RIGHT - 2 40CC DRAWER RIGHT - 2 40CD DRAWER LEFT - 2
CAM DOWEL - 16
2F
HIDDEN CAM - 18
1F
BLACK 9/16" LARGE HEAD SCREW - 20
1S
SILVER 1-1/8" FLAT HEAD SCREW - 20
10S
GOLD 5/16" FLAT HEAD SCREW - 16
3S
METAL PIN - 2
1R
DRAWER FRONT
BRACKET - 2
8G
METAL BRACKET - 6
1G
WASHER - 8
10I
SILVER 1/4" MACHINE SCREW - 8
61S
CAM SCREW - 2
8F
PULL - 4
98K
30S BLACK 1-9/16" FLAT HEAD SCREW - 10
BROWN 1-5/8" FLAT HEAD SCREW - 10
55S

Step 1 Look for this icon. It means a
video assembly tip is available at
www.sauder.com/services/tips
å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor.
å Push eighteen HIDDEN CAMS (1F) into the UPRIGHT (C), PANELS (F, G, and I) and DRAWER BRACES (M65). Then, insert
the metal end of a CAM DOWEL (2F) into each HIDDEN CAM, except for the DRAWER BRACES (M65) .
418529www.sauder.com/services Page 5
I
G
C
F
Do not tighten the HIDDEN CAMS in this step.
Arrow
1F
Arrow
The arrow in the HIDDEN
CAM must point toward the
hole in the edge of the board.
Hole
Insert the metal end of the CAM
DOWEL into the HIDDEN CAM.
Arrow
(18 used)
Arrow
1F
2F
(16 used)
Do not insert CAM
DOWELS into these parts.
M65
M65

Step 2
418529 www.sauder.com/servicesPage 6
8F
å Turn two CAM SCREWS (8F) into the DRAWER FRONTS (D).
D
D

Step 3
418529www.sauder.com/services Page 7
å Fasten a CABINET RIGHT (40CA) and a CABINET
LEFT (40CB) to the ENDS (E). Use four GOLD 5/16" FLAT
HEAD SCREWS (3S) through holes #1 and #3.
å NOTE: After you attach the CABINET RAILS, the ENDS
will be labeled RIGHT END and LEFT END.
E
E
Remember:
Righty tighty.
Lefty loosey.
GOLD 5/16" FLAT HEAD SCREW
(4 used in this step)
3S
Roller end
Roller end
1
2
34
1
2
3
4
This END (E) will now be
called RIGHT END (E).
This END (E) will now be
called LEFT END (E).
Rounded edge
Rounded edge

Step 4
418529 www.sauder.com/servicesPage 8
å Fasten the remaining CABINET RIGHT (40CA) and
CABINET LEFT (40CB) to the UPRIGHT (C). Use
four GOLD 5/16" FLAT HEAD SCREWS (3S) through
holes #1 and #3.
C
Surface with
HIDDEN CAMS
GOLD 5/16" FLAT HEAD SCREW
(4 used in this step)
3S
Roller end
Roller end
1
2
3
4
1
2
3
4
Finished edge

Step 5
418529www.sauder.com/services Page 9
å Fasten the BOTTOM SUPPORTS (B2) to the ENDS (E).
Use eight SILVER 1-1/8" FLAT HEAD SCREWS (10S).
å Fasten the SMALL SLATS (J2) to the BACK PANEL (I)
and UPPER FRONT PANEL (G). Use twelve SILVER 1-1/8"
FLAT HEAD SCREWS (10S).
å NOTE: Use the exact holes shown.
B2
B2
E
E
J2
J2
J2
J2
I
G
Left End Right End
SILVER 1-1/8" FLAT HEAD SCREW
(20 used in this step)
10S
Edge with no holes
If the BOTTOM SUPPORTS (B2) or
SMALL SLATS (J2) have a finished
surface, it should be facing up.
Edge with holes
Finished edge
Edge with holes
Rounded edge

Step 6
418529 www.sauder.com/servicesPage 10
å Fasten six METAL BRACKETS (1G) exactly as shown to the
BOTTOM SUPPPORTS (B2) on the ENDS (E) and UPRIGHT (C).
Use six BLACK 9/16" LARGE HEAD SCREWS (1S).
å NOTE: Be sure the edge of the METAL BRACKETS are even
with the edges of the BOTTOM SUPPORTS and UPRIGHT.
BLACK 9/16" LARGE HEAD SCREW
(6 used in this step)
1S
B2
B2
E
E
Left End
Right End
C
1G
1G
1G
1G
Surface without
HIDDEN CAMS