Sauder HomePlus 411963 User manual

NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
English pg 1-12
Français pg 13-14
Español pg 15-16
Lot # 361774 04/11/14
Purchased: __________________
Be sure to give us a ring before
making any returns. 1-800-523-3987
Storage Cabinet
HomePlus Collection | Model 411963
Need help? Visit Sauder.com to view video assembly tips or chat with a live rep.
Prefer the phone? Call 1-800-523-3987.
Share your journey!
sauder.com
Store behind
closed doors.

Table of Contents Assembly Tools Required
3
4
5-12
13-14
15-16
17-18
19
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Skip the power trip.
This time.
411963 www.sauder.com/servicesPage 2

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
A RIGHT END (1)
B LEFT END (1)
C TOP (1)
D BOTTOM (1)
E BACK (1)
F DOOR (2)
G ADJUSTABLE SHELF (4)
H FRONT SKIRT (1)
J TOP MOLDING (1)
R SIDE SKIRT (2)
Now you know
our ABCs.
411963www.sauder.com/services Page 3
A
B
C
D
E
F
G
H
J
R
F
G
R
G
G

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
411963 www.sauder.com/servicesPage 4
REAR FOOT - 2
K
FRONT FOOT - 2
ITWIST-LOCK® FASTENER - 6 L
SAFETY
BRACKET - 1
OM HINGE - 6 DOOR STOP - 1 P
RUBBER
SLEEVE - 16
S
METAL PIN - 16
QADJUSTABLE
GLIDE - 4
TUPROPEL NUT - 4
BLACK 9/16" LARGE HEAD SCREW - 1
XBLACK 9/16" WAFER HEAD SCREW - 4 Y
NAIL - 40
AA
BLACK 1/2" FLAT HEAD SCREW - 12
Z
BLACK 1-7/8" FLAT HEAD SCREW - 5
VBLACK 7/8" MACHINE SCREW - 4 W
PULL - 2
N

Step 1 Look for this icon. It means a
video assembly tip is available at
www.sauder.com/services/tips
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å To begin assembly, push six SAUDER TWIST-LOCK®
FASTENERS (L) into the large holes in the TOP (C).
411963www.sauder.com/services Page 5
L
L
L
C
Do not tighten the TWIST-LOCK® FASTENERS in this step.
Scan this QR code or go to this address:
http://qr.sauder.com/?ID=1707
to watch a video on how to assemble your unit.

Step 2
å Fasten the ENDS (A and B) to the TOP (C). Tighten four
TWIST-LOCK® FASTENERS.
å Fasten the TOP MOLDING (J) to the TOP (C). Tighten two
TWIST-LOCK® FASTENERS.
411963 www.sauder.com/servicesPage 6
B
Edge with
TWIST-LOCK®
FASTENERS
C
A
J
How to use the SAUDER TWIST-LOCK®FASTENER
1. Insert the dowel end of the FASTENER into the hole of
the adjoining part.
NOTE: The dowel end of the FASTENER must remain
fully inserted in the hole of the adjoining part while
locking the FASTENER.
2. Tighten the FASTENER with a Phillips screwdriver as
tight as possible.
Dowel end
Long finished edge
Wide edge
Finished
surface

å Push the DOOR STOP (P) into the hole in the TOP (C).
å Fasten the BOTTOM (D) to the ENDS (A and B). Use four
BLACK 1-7/8" FLAT HEAD SCREWS (V).
Step 3
411963www.sauder.com/services Page 7
D
C
P
A
B
Rounded edge
Unfinished
surface
Do not stand the unit upright without the
BACK fastened. The unit may collapse.
Caution
BLACK 1-7/8" FLAT HEAD SCREW
(4 used in this step)
V

Step 4
å Slide the FEET (I and K) into the notches in the SKIRTS (H
and R) as shown in the upper diagram.
å Use a hammer to drive a PROPEL NUT (U) into the holes in
the FEET (I and K). Now, turn an ADJUSTABLE GLIDE (T)
into each PROPEL NUT.
å Fasten the SKIRTS (H and R) to the BOTTOM (D) as shown
in the lower diagram. Use four BLACK 9/16" WAFER HEAD
SCREWS (Y) through the FEET and into the BOTTOM.
411963 www.sauder.com/servicesPage 8
H
R
R
I
K
I
K
T
U
H
R
R
D
Insert an ADJUSTABLE SHELF (G)
between the ENDS (A and B) for
support before turning the unit over.
G
A
B
BLACK 9/16" WAFER HEAD SCREW
(4 used in this step)
Y
(4 used)

å Carefully turn your unit over onto its front edges. Unfold
the BACK (E) and lay it over your unit.
å Make equal margins along all four edges of the BACK (E).
Push on opposite corners of your unit if needed to make
it "square".
å Fasten the BACK (E) to your unit using the NAILS (AA).
Step 5
411963www.sauder.com/services Page 9
E
Do not stand the unit upright without the
BACK fastened. The unit may collapse.
Caution
NAIL
(40 used in this step)
AA

Step 6
å Fasten three HINGES (M) to each DOOR (F) as shown in the upper diagram below. Use twelve BLACK 1/2" FLAT
HEAD SCREWS (Z).
å Carefully stand your unit upright as shown in the lower diagram.
å Before fastening the DOOR to your unit, be sure the mounting screw is against the stops as shown in the lower
diagram. If it isn't, loosen the mounting screw to slide it against the stops. Then tighten the mounting screw.
å Fasten a DOOR (F) to the LEFT END (B). Use the screws in the HINGES. See the next step for adjustments.
å Fasten a PULL (N) to the DOOR (F). Use two BLACK 7/8" MACHINE SCREWS (W).
å Repeat this step for the other door.
411963 www.sauder.com/servicesPage 10
F
F
F
B
N
M
Adjusting
screw
Mounting
screw
M
Adjusting
screw
Mounting
screw
BLACK 1/2" FLAT HEAD SCREW
(12 used for the HINGES)
Z
BLACK 7/8" MACHINE SCREW
(4 used for the PULLS)
W
Mounting
screw
Stop
Hinge