Sauder North Avenue 420035 User manual

Need help? Visit Sauder.com to view video assembly tips or chat with a live rep.
Prefer the phone? Call 1-800-445-1527.
Share your journey!
sauder.com
You'll love what we
have in storage.
Display Cabinet
North Avenue Collection | Model 420035
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
English pg 1-17
Français pg 18-20
Español pg 21-24
Lot #: 392458
Date Purchased: __________________
06/15/16
Be sure to give us a ring before
making any returns. 1-800-445-1527

Table of Contents Assembly Tools Required
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Skip the power trip.
This time.
3
4
5-17
18-20
21-24
25-26
27
Use of a TV that is too heavy or large is hazardous. A TV that is too heavy will create a risk of a tip-over that can cause severe injury or
death. A TV that is too large for the available space might be accidentally pushed or bumped o the furniture, or subject to tip-over.
• Check the size and weight of your TV. Compare it to the diagram below – before you begin assembly!
• This Sauder unit is designed for use with televisions weighing less than 35 pounds. Never use with a TV that weighs more.
• The size of the television, front-to-back and side-to-side, must fit within the space defined in the diagram.
• Never place the front edge of the TV past the front edge of the TV support shelf (or stop molding – if equipped)
• Never allow the sides of the TV to extend past the side edges of the TV support surface.
• If the TV has a CRT picture tube, the picture tube cone may extend past the rear of the support shelf.
• Be sure to apply the warning label as instructed in the last assembly step. The label provides important safety related information.
WARNING
!
35 lbs.
35 lbs.
16-1/4"
16-1/4"
31-1/2"
31-1/2"
Page 2 www.sauder.com 420035

åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
Part Identification
A TOP (1)
B LEFT END (1)
C RIGHT END (1)
D BOTTOM (1)
E BACK (1)
F TOP MOLDING (1)
G ADJUSTABLE SHELF (1)
H DOOR (2)
I END LEG (2)
J BACK BRACE (1)
K FRONT BRACE (1)
A
B
C
D
E
F
G
H
H
I
I
J
K
Page 3www.sauder.com420035

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
1-3/16" ALLEN SCREW - 7
13
6
HINGE - 4
1-3/8" ALLEN SCREW - 4
12
CAM SCREW - 7
1
ALLEN WRENCH - 1
8
9/16" FLAT HEAD SCREW - 24
15
NAIL - 16
9
1-5/8" FLAT HEAD SCREW - 4
11
3/4" MACHINE SCREW - 2
14
HIDDEN CAM - 7
3
1/2" PAN HEAD SCREW - 2
16
KNOB - 2
5
BUMPER - 2
7
WOOD DOWEL -12
4
Ne jamais utiliser ce meuble avec
un téléviseur qui soit trop large
ou trop lourd. Risque de
provoquer des blessures graves,
voire mortelles. Le télévision et le
meuble seront instable et
risquent de se renverser.
-Le téléviseur doit peser
ou moins.
-La socle du téléviseur doit
pouvoir être placé complètement
sur cette tablette.
Consulter le manuel
d’instructions pour information
complete convernant la sécurité.
Remarque: Cette étiquette est
permanente. Ne pas essayer de la
retirer. Causer des dommages à la
surface.
Never use this furniture
with a TV that is too large or
too heavy. Severe injury or
death can occur. The TV and
furniture will be unstable
and may tip.
-The TV must weigh less
than
-The base of the TV must
be able to sit completely on
the shelf.
Refer to instruction book
for complete safety
information.
Note: This is a permanent
label. Do not try to remove.
Surface will be damaged.
Nunca use este mueble con un
televisor que es demasiado
grande o demasiado pesado.
Podría resultar en una lesión
grave hasta fatal. El televisior y
el mueble estarán inestable y
pueden volcarse.
-El televisor debe pesar
o menos.
-La base del televisior debe
poder colocarse
completamente sobre este
estante.
Consulte el folleto de
instrucciones para información
completa sobre la seguridad.
Nota: Esta etiqueta es
permanente. No intente quitarla.
Causará daño a la super .
WARNING ADVERTENCIA AVERTISSEMENT
11-07
35 lbs. 15 kg 15 kg
WARNING LABEL - 1
10
(Refer to the last step for proper
location and application)
Page 4 www.sauder.com 420035
Hardware Identification
METAL PIN - 4
2

Look for this icon. It means a
video assembly tip is available at
www.sauder.com/services/tips
Step 1
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å Turn seven CAM SCREWS (1) into the TOP (A), LEFT END (B),
and RIGHT END (C).
B
C
A
1
(7 used)
Page 5www.sauder.com420035
Remember:
Righty tighty.
Lefty loosey.

å Push twelve WOOD DOWELS (4) into the ENDS (B and C)
and TOP MOLDING (F). Be sure to use the exact holes shown.
Step 2
B
C
F
4
4
4
Page 6 www.sauder.com 420035

å Push two HIDDEN CAMS (3) into the TOP MOLDING (F).
å Fasten the TOP MOLDING (F) to the ENDS (B and C).
Tighten the HIDDEN CAMS.
å NOTE: Be sure the follow the diagram to the right on how
to tighten the HIDDEN CAM.
å NOTE: Be sure the WOOD DOWELS insert into the holes
in the ENDS.
Step 3
B
C
F
3
21
3
The arrow must
point toward the
edge of the board.
3This surface will be
facing out of the part
after it is pushed in the
TOP MOLDING (F).
Page 7www.sauder.com420035
The arrow must point
toward the edge of the
board and CAM SCREW.

å Insert five HIDDEN CAMS (3) into the ENDS (B and C)
and TOP MOLDING (F).
å Fasten the TOP (A) to the ENDS (B and C) and TOP
MOLDING (F). Tighten the HIDDEN CAMS.
å NOTE: Be sure the WOOD DOWELS in the ENDS and
TOP MOLDING insert into the holes in the TOP.
Step 4
3
3
21
3
The arrow must
point toward the
edge of the board.
B
C
F
These edges must be even.
Page 8 www.sauder.com 420035
A

These holes
must be here.
å Fasten the BOTTOM (D) to the ENDS (B and C). Use four
1-5/8" FLAT HEAD SCREWS (11).
å NOTE: Be sure the WOOD DOWELS in the ENDS insert
into the holes in the BOTTOM.
Step 5
B
C
These edges must be even.
1-5/8" FLAT HEAD SCREW
(4 used in this step)
11
D
Page 9www.sauder.com420035

Step 6
å Carefully turn your unit over onto its front edges. Unfold
the BACK (E) and lay it over your unit.
å Make equal margins along all four edges of the BACK (E).
Push on opposite corners of your unit if needed to make
it "square".
å Fasten the BACK (E) to your unit using the NAILS (9).
Do not stand the unit upright without the
BACK fastened. The unit may collapse.
Caution
NAIL
(16 used in this step)
9
E
Page 10 www.sauder.com 420035
Notch
Notch