Sauder Manhattan Gate 429254 User manual

sauder.com
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
sauder.com
CONTACT US FIRST
BEFORE MAKING ANY RETURNS TO THE STORE.
sauder.com
CONTACT US FIRST
BEFORE MAKING ANY RETURNS TO THE RETAILER.
Visit sauder.com/service to order replacement parts, view video assembly tips, or chat with a live rep.
Prefer the phone? Give us a ring at 1-800-445-1527.
Customer Service is available Monday-Friday - 9 a.m. to 5:30 p.m. EST (except holidays)
Sauder.com
Share your journey!
English pg 1-31
Français pg 32-35
Español pg 36-39
Lot # 565063 04/12/21
Purchased: __________________
Executive Desk
Manhattan Gate Collection | Model 429254
Business or pleasure.
Works both ways.

Part Identification
Hardware Identification
Hardware Usage Guide
Assembly Steps
Français
Español
Safety
Warranty
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Table of Contents Assembly Tools Required
3
4-5
6
7-31
32-35
36-39
40-42
43
Page 2 www.sauder.com/service 429254

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
A TOP (1)
B RIGHT END (1)
C LEFT END (1)
D MODESTY PANEL (1)
E RIGHT UPRIGHT (1)
F LEFT UPRIGHT (1)
G BOTTOM BRACE (2)
H SMALL LEFT DRAWER FRONT (1)
J SMALL LEFT DRAWER SIDE (2)
K SMALL DRAWER BACK (2)
L LARGE DRAWER BOTTOM (2)
M LARGE LEFT DRAWER FRONT (1)
N LOCKING RIGHT DRAWER SIDE (1)
O BACK BRACE (1)
P LARGE LEFT DRAWER SIDE (2)
Q LARGE DRAWER BACK (2)
R DRAWER BRACE (2)
S DRAWER PULL (4)
T SMALL RIGHT DRAWER FRONT (1)
U LARGE RIGHT DRAWER FRONT (1)
V LARGE RIGHT DRAWER SIDE (1)
W SMALL RIGHT DRAWER SIDE (2)
X SMALL DRAWER BOTTOM (2)
A
B
C
DE
F
G
G
H
J
J
K
K
L
L
M
N
O
P
P
Q
Q
R
R
T
U
V
W
W
X
X
S
S
S
S
Page 3www.sauder.com/service429254

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
SMALL WOOD
DOWEL - 8
12
LARGE WOOD
DOWEL - 24
11
7LONG FILE
GLIDE - 4 8SHORT FILE GLIDE - 4
GROMMET
WITH CAP- 2
13 LOCK SET - 1 14 APPLIQUE CARD - 2 15 L-WRENCH - 1 16
(EXTENSION SET SHOWN SEPARATED)
5EXTENSION RAIL - 4 6EXTENSION SLIDE - 4
1RIGHT CABINET
RAIL - 2 3RIGHT DRAWER SLIDE - 2
2LEFT CABINET
RAIL - 2 4LEFT DRAWER SLIDE - 2
HIDDEN CAM -48
9CAM SCREW - 48 10
Page 4 www.sauder.com/service 429254

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
1" FLAT HEAD SCREW - 4
19
3/8" PAN HEAD SCREW - 24
21
5/8" HEX HEAD SCREW - 4
20
1/2" FLAT HEAD SCREW - 34
22
2-3/8" HEX HEAD SCREW - 4
17 1-1/2" FLAT HEAD SCREW - 16
18
Page 5www.sauder.com/service429254

Hardware Usage Guide
HOW TO USE A HIDDEN CAM & CAM SCREW OR CAM DOWEL
NOTE: Various CAM SCREWS or a CAM DOWEL may be used.
Cam Screws Cam Dowel
Turn the CAM SCREW or
gently tap the CAM DOWEL
until the shoulder is against
the surface of the part.
1.
Hidden Cam
Arrow
Push a HIDDEN CAM into
the part. The arrow in the
HIDDEN CAM must point
toward the hole in the
edge of the board.
Hole
2.
3.
1
2
Insert the CAM SCREW or CAM DOWEL into the
HIDDEN CAM. Tighten the HIDDEN CAM.
Page 6 www.sauder.com/service 429254

Step 1 Look for this icon. It means a video assembly tip is
available at www.sauder.com/service/tips
Find the numbered video or scan the QR code.
å Assemble your unit on a carpeted floor or on the empty carton
to avoid scratching your unit or the floor.
å Turn four CAM SCREWS (10) into the UPRIGHTS (E and F).
å Push ten HIDDEN CAMS (9) into the UPRIGHTS (E and F).
E
F
1
10
9
Arrow
Arrow
9
9
Arrow
Page 7www.sauder.com/service429254

Step 2
å Separate the EXTENSION SLIDES (6) from the EXTENSION RAILS (5) as shown in the upper diagram below. Be
prepared, the parts are greasy.
å Fasten one EXTENSION RAIL (5) to the RIGHT UPRIGHT (E). Use three 3/8" PAN HEAD SCREWS (21) through the
exact holes shown.
å NOTE: For each EXTENSION RAIL, turn a SCREW into the hole shown in the enlarged diagram. Then, slide the inner
cartridge of the EXTENSION RAIL in to find the other holes that line up with the holes in the UPRIGHT. Turn a SCREW
into each hole.
å NOTE: The EXTENSION SLIDES will be used later for the DRAWERS.
å Fasten one of the CABINET LEFT RAILS (2) to the RIGHT UPRIGHT (E).
Use three 1/2" FLAT HEAD SCREWS (22).
E
Slide the lever and pull the SLIDE from the RAIL.
3/8" PAN HEAD SCREW
(3 used for the EXTENSION RAILS)
21
6 5
5
7
Open end
Open end
Roller end
2
2
1/2" FLAT HEAD SCREW
(3 used for the CABINET RAIL)
22
RR
Page 8 www.sauder.com/service 429254
Roller end

å Fasten one EXTENSION RAIL (5) to the LEFT UPRIGHT (F). Use three 3/8" PAN HEAD SCREWS (21) through the
exact holes shown.
å NOTE: For each EXTENSION RAIL, turn a SCREW into the hole shown in the enlarged diagram. Then, slide the inner
cartridge of the EXTENSION RAIL in to find the other holes that line up with the holes in the UPRIGHT. Turn a SCREW
into each hole.
å Fasten one of the CABINET RIGHT RAILS (1) to the LEFT UPRIGHT (F). Use three 1/2" FLAT HEAD SCREWS (22).
Step 3
F
3/8" PAN HEAD SCREW
(3 used for the EXTENSION RAILS)
21
5
5
7
Open end
Roller end
1
RR
1
1/2" FLAT HEAD SCREW
(3 used for the CABINET RAIL)
22
Page 9www.sauder.com/service429254
Roller end

Step 4
å Turn eight CAM SCREWS (10) into the ENDS (B and C).
å Push six HIDDEN CAMS (9) into the ENDS (B and C).
B
C
10
9
Arrow
1
Some assembly
(and snacks) required.
Page 10 www.sauder.com/service 429254