Sauder Trestle 414602 User manual

PLEASE CONTACT US
BEFORE RETURNING
YOUR UNIT TO THE STORE
1-800-523-3987
www.sauder.com
Made in the USA
Archbold, OH
NOTE: THIS INSTRUCTION BOOKLET CONTAINS
IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Lot #: 355665 09 / 10 / 13
Date Purchased: ____________________
English.................... Page 1-12
Français...............Pages 13-14
Espanol.............Páginas 15-16
414602
5-Shelf Bookcase
Trestle Collection

ADULT ASSEMBLY REQUIRED
ASSEMBLY TOOLS REQUIRED
Hammer
No. 2 Phillips Screwdriver
Tip Shown Actual Size
TABLE OF CONTENTS
Part Identification.......................3
Hardware Identification .............4
Assembly Steps....................5-12
Français..............................13-14
Espanol...............................15-16
Safety .................................17-18
Warranty...................................19
Page 2 www.sauder.com/services 414602

PART IDENTIFICATION: While not all parts are labeled, some of the parts will have a label or an inked
letter on the edge to help distinguish similar parts from each other. Use this PART IDENTIFICATION to help
identify similar parts.
A TOP 1
B TOP SHELF 1
C CENTER SHELF 1
D UPPER CENTER SHELF 1
E LOWER CENTER SHELF 1
F BOTTOM SHELF 1
G BACK 5
H RIGHT FRONT LEG 1
I LEFT FRONT LEG 1
J RIGHT REAR LEG 1
K LEFT REAR LEG 1
L SKIRT 2
M LEFT SIDE SKIRT 1
N RIGHT SIDE SKIRT 1
Page 3
www.sauder.com/services414602
A
B
C
D
E
F
G
H
I
J
K
L
M
N
L
G
G
G
G

HARDWARE IDENTIFICATION
Screws are shown actual size. You may receive extra hardware with your unit.
Page 4 www.sauder.com/services 414602
SILVER 1-1/8" FLAT HEAD SCREW - 8
10S
HIDDEN CAM - 38
1F
CAM SCREW - 30
8F
CAM DOWEL - 8
2F
METAL PIN - 10
1R
BLACK 9/16" LARGE HEAD SCREW - 1
1S
BLACK 1-1/4" FLAT HEAD SCREW - 10
74S
CAM COVER - 32
12P SCREW COVER - 8 20P
SAFETY BRACKET - 1
1G
BLACK 1-7/8" PAN HEAD SCREW - 1
16S

Look for this icon. It means a video
assembly tip is available at:
www.sauder.com/services/tips
1
1
S
t
e
p
Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor.
Push thirty-eight HIDDEN CAMS (1F) into the SHELVES (B, C, D, E, and F), BACKS (G), and SKIRTS (L, M, and N). Then, insert
the metal end of a CAM DOWEL (2F) into each HIDDEN CAM in the SKIRTS (L, M, and N).
Page 5
www.sauder.com/services414602
Do not tighten the HIDDEN CAMS in this step.
Arrow
1F
(38 used)
(8 used)
Arrow
1F
2F
Insert the metal end of the CAM
DOWEL into the HIDDEN CAM.
Arrow
Arrow
1F
B
C
D
E
F
G
LL
G
G
G
G
N
M

2
2
S
t
e
p
Page 6 www.sauder.com/services 414602
Turn thirty CAM SCREWS (8F) into the LEGS (H, I, J, and K).
8F (30 used)
J
H
I
K
These holes will not
have CAM SCREWS.
These holes will not
have CAM SCREWS.

3
3
S
t
e
p
Page 7
www.sauder.com/services414602
H
I
K
M
N
J
Fasten the SKIRTS (M and N) to the LEGS (H, I, J, and K).
Surface
with
HIDDEN
CAMS
Surface with
HIDDEN CAMS
Edge with
CAM
DOWELS
SILVER 1-1/8" FLAT HEAD SCREW
(8 used in this step)
10S

4
4
S
t
e
p
Page 8 www.sauder.com/services 414602
J
Insert five METAL PINS (1R) into the holes shown in the RIGHT REAR LEG (J).
Fasten the BACKS (G) to the RIGHT REAR LEG (J). Tighten five HIDDEN CAMS.
NOTE: Be sure the METAL PINS (1R) in the LEG (J) insert into the holes in the ends of the BACKS (G).
Insert five METAL PINS (1R) into the smaller holes in the BACKS (G).
1R
(10 used)
Edge
closer to
HIDDEN
CAMS
1R
G
G
G
G
G

5
5
S
t
e
p
Page 9
www.sauder.com/services414602
B
C
D
E
F
H
J
Surface
with
HIDDEN
CAMS
Finished edge
NOTE: You may need someone's help in this step.
Fasten the SHELVES (B, C, D, E, and F) to the LEGS (H and J) as shown in the upper diagram. Tighten ten HIDDEN CAMS.
Fasten the SHELVES (B, C, D, E, and F) and BACKS (G) to the LEGS (I and K) as shown in the lower diagram. Tighten fifteen
HIDDEN CAMS.
NOTE: Be sure the METAL PINS (1R) in the ends of the BACKS (G) insert into the holes in the LEGS (I and K).
B
C
D
E
F
I
K
G
G
G
G
G
Finished surface
Finished surface
Surface
with
HIDDEN
CAMS
Surface
with
HIDDEN
CAMS
Surface
with
HIDDEN
CAMS
Surface
with
HIDDEN
CAMS

6
6
S
t
e
p
L
Fasten the SHELVES (B, C, D, E, and F) to the BACKS (G). Use ten BLACK 1-1/4" FLAT HEAD SCREWS (74S).
NOTE: There are no pre-drilled holes in the back of the SHELVES (B, C, D, E, and F). Use extra force when turning these screws.
Fasten the SKIRT (L) to the BOTTOM SHELF (F). Tighten two HIDDEN CAMS.
B
C
D
E
F
G
G
G
G
G
BLACK 1-1/4" FLAT HEAD SCREW
(10 used in this step)
74S
Surface with
HIDDEN CAMS
I
K
Page 10 www.sauder.com/services 414602