Sauder 418645 User manual

NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
Enlish p 1-18
Français p 19-21
Español p 22-24
Lot # 368870 02/05/15
Purchased: __________________
Be sure to ive us a rin before
makin any returns. 1-800-523-3987
Dresser
Orchard Hills Collection | 418645
Need help? Visit Sauder.com to view video assembly tips or chat with a live rep.
Prefer the phone? Call 1-800-523-3987.
Share your journey!
sauder.com
Don't et cauht with
your pants on the
round.

Table of Contents Assembly Tools Required
3
4
5-18
19-21
22-24
25-26
27
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Skip the power trip.
This time.
418645 www.sauder.com/servicesPae 2

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the ede
to help distinuish similar parts from each other. Use this part identification to help identify similar parts.
A RIGHT END (1)
B LEFT END (1)
C UPRIGHT (1)
D TOP (1)
E BRACE (2)
F BASE (1)
G BACK (1)
H LARGE DRAWER FRONT (4)
L SMALL DRAWER FRONT (2)
Q FRONT MOLDING (1)
R RIGHT MOLDING (1)
S LEFT MOLDING (1)
T DRAWER BRACE (6)
D12 SMALL DRAWER RIGHT SIDE (2)
D13 SMALL DRAWER LEFT SIDE (2)
D30 LARGE DRAWER RIGHT SIDE (4)
D31 LARGE DRAWER LEFT SIDE (4)
D166 SMALL DRAWER BACK (2)
D167 LARGE DRAWER BACK (4)
D974 DRAWER BOTTOM (6)
Now you know
our ABCs.
418645www.sauder.com/services Pae 3
A
B
C
D
E
F
G
H
L
E
Q
S
R
T
T
D974
D974
D166
D167
D12
D13
D30
D31

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
418645 www.sauder.com/servicesPae 4
35GA CABINET RIGHT - 6 35GB CABINET LEFT - 6 35GC DRAWER RIGHT - 6 35GD DRAWER LEFT - 6
HIDDEN CAM - 8
1F CAM DOWEL - 8 2F
ANGLE BRACKET - 14
5G
SAFETY
BRACKET - 1
1G
MOLDING
CONNECTOR - 2
19F
10A SLIDE CAM - 12
PULL MOUNT - 12
115K
PULL - 6
114K 5L WARNING LABEL - 1
(Refer to Step 13 for proper
location and application)
WARNING
Serious or fatal crushing injuries can occur
from furniture tip-over. To help prevent
tip-over:
• Place heaviest items in the lowest drawers.
• Unless specifically desined to accommodate, do not
set TVs or other heavy objects on top of this product.
• Never allow children to climb or han on drawers,
doors, or shelves.
• Never open more than one drawer at a time.
• If equipped with a drawer interlock system, do not
defeat or remove it.
Use of tip-over restraints may only reduce, but not
eliminate, the risk of tip-over.
This is a permanent label. Do not attempt to remove!
04/10 332296
BLACK 1-7/8" FLAT HEAD SCREW - 5
2S
30S BLACK 1-9/16" FLAT HEAD SCREW - 30
SILVER 1-1/8" FLAT HEAD SCREW - 8
10S
SILVER 3/4" MACHINE SCREW - 12
20S
BLACK 9/16" LARGE HEAD SCREW - 29
1S
3S GOLD 5/16" FLAT HEAD SCREW - 48
NAIL - 38
1N

Step 1 Look for this icon. It means a
video assembly tip is available at
www.sauder.com/services/tips
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratchin your unit or the floor.
å Push eiht HIDDEN CAMS (1F) into the UPRIGHT (C) and
DRAWER BRACES (T). Then, insert the metal end of a
CAM DOWEL (2F) into each HIDDEN CAM.
418645www.sauder.com/services Pae 5
Arrow
1F
2F
Do not tihten the HIDDEN CAMS in this step.
Insert the metal end of the CAM
DOWEL into the HIDDEN CAM.
Arrow
C
T
T
T
T
T
T
(8 used)

Step
å Fasten six ANGLE BRACKETS (5G) to the ENDS (A and B)
and UPRIGHT (C). Use six BLACK 9/16" LARGE
HEAD SCREWS (1S).
å NOTE: Be sure the edes of the ANGLE BRACKETS are
even with the edes of the ENDS and UPRIGHT.
Step 2
418645 www.sauder.com/servicesPae 6
BLACK 9/16" LARGE HEAD SCREW
(6 used in this step)
1S
C
B
Surface
with holes
Surface with
HIDDEN CAMS
A
Surface
with holes
5G
5G
5G
Ede with
HIDDEN CAMS
Some assembly
(and snacks) required.
Finished ede
Finished ede

å Fasten the CABINET RIGHTS (35GA) to the RIGHT END (A)
and UPRIGHT (C) and the CABINET LEFTS (35GB) to the
LEFT END (B) and other surface of the UPRIGHT (C). Use
twenty-four GOLD 5/16" FLAT HEAD SCREWS (3S)
throuh holes #1 and #3.
Step 3
418645www.sauder.com/services Pae 7
1
2
3
1
2
3
GOLD 5/16" FLAT HEAD SCREW
(24 used in this step)
3S
C
Surface with
HIDDEN CAMS
B
A
1
2
31
2
3
1
2
3
1
2
3
1
2
3
1
2
3
1
2
3
Roller end
Roller end
These holes
must be here.

Step 4
å Tap two MOLDING CONNECTORS (19F) into the notches
in the MOLDINGS (Q, R, and S).
418645 www.sauder.com/servicesPae 8
Flat end Flat end
Use your hammer to tap the MOLDING CONNECTORS (19F) into the notches in the MOLDINGS.
19F
Q
19F
R
S

å First, fasten the ENDS (A and B) to the MOLDINGS (R and S).
Use four BLACK 1-7/8" FLAT HEAD SCREWS (2S).
å Now, fasten the TOP (D) to the MOLDINGS (Q, R, and S). Use
eiht SILVER 1-1/8" FLAT HEAD SCREWS (10S).
å NOTE: Do not overtihten the SCREWS into the TOP.
Step 5
418645www.sauder.com/services Pae 9
BLACK 1-7/8" FLAT HEAD SCREW
(4 used for the ENDS)
2S
Finished ede
Finished ede
B
A
R
D
Q
S
SILVER 1-1/8" FLAT HEAD SCREW
(8 used for the TOP)
10S
Finished surface
Finished ede
Do not stand the unit upriht without the
BACK fastened. The unit may collapse.
Caution

Step 6
å Fasten the UPRIGHT (C) to the TOP (D). Tihten two
HIDDEN CAMS.
418645 www.sauder.com/servicesPae 10
C
D
Start Tihten
Arrow
Minimum
190 derees
Caution
Risk of damae or
injury. HIDDEN CAMS
must be completely
tihtened. HIDDEN
CAMS that are not
completely tihtened
may loosen, and parts
may separate. To
completely tihten:
Arrow
Maximum
210 derees
Surface
with
HIDDEN
CAMS
Finished ede