Sauder Edge Water Credenza 415321 User manual

PLEASE CONTACT US
BEFORE RETURNING
YOUR UNIT TO THE STORE
1-800-523-3987
www.sauder.com
Made in the USA
Archbold, OH
NOTE: THIS INSTRUCTION BOOKLET CONTAINS
IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
English.................... Page 1-28
Français...............Pages 29-32
Espanol.............Páginas 33-36
Lot #: 353834 07 / 19 / 13
Date Purchased: ____________________
415321
Credenza
Edge Water Collection

ADULT ASSEMBLY REQUIRED
TABLE OF CONTENTS
Part Identification.......................3
Hardware Identification .........4-5
Assembly Steps....................6-28
Français..............................29-32
Espanol...............................33-36
Safety .................................37-38
Warranty...................................39
ASSEMBLY TOOLS REQUIRED
Hammer
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Use of a TV that is too heavy or large is hazardous. A TV that is too heavy will create a risk of a tip-over that can cause severe injury
or death. ATV that is too large for the available space might be accidentally pushed or bumped off the furniture, or subject to tip-over.
• Check the size and weight of your TV. Compare it to the diagram below – before you begin assembly!
• This Sauder unit is designed for use with televisions weighing less than 95 pounds. Never use with a TV that weighs more.
• The size of the television, front-to-back and side-to-side, must fit within the space defined in the diagram.
• Never place the front edge of the TV past the front edge of the TV support shelf (or stop molding – if equipped)
• Never allow the sides of the TV to extend past the side edges of the TV support surface.
• If the TV has a CRT picture tube, the picture tube cone may extend past the rear of the support shelf.
• Be sure to apply the warning label as instructed in the last assembly step. The label provides important safety related information.
WARNING
71"
20-1/4"
95 lbs.
Page 2 www.sauder.com/services 415321

PART IDENTIFICATION: While not all parts are labeled, some of the parts will have a label or an inked
letter on the edge to help distinguish similar parts from each other. Use this PART IDENTIFICATION to help
identify similar parts.
A RIGHT END 1
B LEFT END 1
C RIGHT UPRIGHT 1
D LEFT UPRIGHT 1
D10 DRAWER RIGHT SIDE 3
D11 DRAWER LEFT SIDE 3
D174 DRAWER BACK 3
D983 DRAWER BOTTOM 3
E TOP 1
F BOTTOM 1
G RIGHT BOTTOM 1
H LEFT BOTTOM 1
I BACK 2
J CENTER BACK 2
K BRACE 2
L DOOR 2
M ADJUSTABLE SHELF 4
N FRONT LEG 4
O BACK LEG 2
P VALANCE 1
Q DOOR VALANCE 2
R SKIRT 1
S DOOR SKIRT 2
T SIDE SKIRT 2
U DRAWER FRONT 3
V FRONT MOLDING 1
W RIGHT MOLDING 1
X LEFT MOLDING 1
Y BRACE MOLDING 2
Z DOOR GLASS 2
AA DOOR PANEL 2
BB FEET 6
CC DRAWER BRACE 3
A
B
C
D
E
F
G
H
I
I
J
J
K
K
L
L
M
M
M
M
N
N
N
N
O
O
P
Q
Q
R
S
S
T
T
U
V
W
X
Y
ZAA
D10
D11
D174
D983
CC
BB
BB
BB
BB
BB
BB
Page 3
www.sauder.com/services415321

HARDWARE IDENTIFICATION
40CB CABINET LEFT - 3 40CA CABINET RIGHT - 3 40CC DRAWER RIGHT - 3
40CD DRAWER LEFT - 3
3M ANTI-SKID PAD - 1
NAIL - 44
1N
KNOB - 8
17K
BACKPLATE - 2
18K
METAL PIN - 28
1R RUBBER SLEEVE - 16 2R
14H HINGE - 4
METAL BRACKET - 7
4G
CAM DOWEL - 24
2F
HIDDEN CAM - 35
1F
CAM SCREW - 11
8F MOLDING CONNECTOR - 2 17F
DOOR STOP - 2
4I
46M CLIP - 16
SLIDE CAM - 6
10A
Page 4 www.sauder.com/services 415321
WARNING LABEL - 1
3L
(Refer to the step 22 for proper location and application)

HARDWARE IDENTIFICATION
Screws are shown actual size. You may receive extra hardware with your unit.
BLACK 2-1/4" FLAT HEAD SCREW - 4
26S
BLACK 1/2" FLAT HEAD SCREW - 8
11S
BLACK 1-5/8" PAN HEAD SCREW - 6
27S
BLACK 9/16" LARGE HEAD SCREW - 14
1S
BROWN 1-1/2" FLAT HEAD SCREW - 16
14S
BLACK 7/8" MACHINE SCREW - 6
37S
BLACK 1-1/8" MACHINE SCREW - 2
21S
BLACK 1-1/8" PAN HEAD SCREW - 4
9S
GOLD 5/16" FLAT HEAD SCREW - 24
3S
BLACK 1-9/16" FLAT HEAD SCREW - 15
30S
BLACK 9/16" PAN HEAD SCREW - 16
51S
Page 5
www.sauder.com/services415321

Look for this icon. It means a video
assembly tip is available at:
www.sauder.com/services/tips
1
1
S
t
e
p
Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor.
Push thiry-five HIDDEN CAMS (1F) into the ENDS (A and B), UPRIGHTS (C and D), BOTTOMS (F, G, and H), BRACES (K), and
DRAWER BRACES (CC). Then, insert the metal end of a CAM DOWEL (2F) into each HIDDEN CAM, except the long edges of
the ENDS (A and B), UPRIGHTS (C and D), and short edge of the BRACES (CC).
Page 6 www.sauder.com/services 415321
Do not tighten the HIDDEN CAMS in this step.
Do not insert
CAM DOWELS
into these edges.
Do not insert
CAM DOWELS
into these edges.
Arrow
(35 used)
(24 used)
1F
2F
2F
Insert the metal end of the CAM
DOWEL into the HIDDEN CAM.
Arrow
1F
Arrow
1F
2F
Arrow
D
C
A
B
H
G
K
K
F
CC
CC
CC

Page 7
www.sauder.com/services415321
Turn eleven CAM SCREWS (8F) into the FRONT LEGS (N) and DRAWER FRONTS (U).
8F
NN
N
N
U
U
U
2
2
S
t
e
p

Tap two MOLDING CONNECTORS (17F) into the notches in the MOLDINGS (V, W, and X).
Page 8 www.sauder.com/services 415321
3
3
S
t
e
p
Flat end Flat end
Use your hammer to tap the MOLDING CONNECTOR (17F) into the notches in the MOLDINGS.
17F
17F
V
X
W

Fasten the MOLDINGS (V, W, and X) to the TOP (E). Use nine BROWN 1-1/2" FLAT HEAD SCREWS (14S).
Page 9
www.sauder.com/services415321
4
4
S
t
e
p
14S
BROWN 1-1/2" FLAT HEAD SCREW
(9 used in this step)
W
X
V
Surface with holes
Rounded edge
Rounded edge
Rounded edge
E

Page 10 www.sauder.com/services 415321
5
5
S
t
e
p
Fasten the CABINET RIGHTS (40CA) and CABINET LEFTS (40CB) to the UPRIGHTS (C and D). Use twelve GOLD 5/16" FLAT
HEAD SCREWS (3S) through holes #1 and #4.
GOLD 5/16" FLAT HEAD SCREW
(12 used in this step)
3S
1
2
34
43
2
1
Roller end
1
2
34
1
2
34
43
2
1
43
2
1
Roller end
C
D
Curved edge
Surface without
HIDDEN CAMS Surface without
HIDDEN CAMS