Sauder Shoal Creek 422194 User manual

Need help? Visit Sauder.com to view video assembly tips or chat with a live rep.
Prefer the phone? Call 1-800-523-3987.
Share your journey!
sauder.com
Sit and surf.
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
English pg 1-35
Français pg 36-39
Español pg 40-44
Lot # 505895 07/05/17
Purchased: __________________
Be sure to give us a ring before
making any returns. 1-800-523-3987
Computer Desk
Shoal Creek Collection | Model 422194

Table of Contents Assembly Tools Required
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Skip the power trip.
This time.
3
4-5
6-35
36-39
40-44
45-46
47
422194 www.sauder.com/servicesPage 2
Short Screwdriver

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
A RIGHT END (1)
B LEFT END (1)
C UPRIGHT (1)
DRIGHT FRONT/LEFT
REAR LEG (2)
D28 LARGE RIGHT DRAWER SIDE (1)
D29 LARGE LEFT DRAWER SIDE (1)
D78 LARGE DRAWER BACK (1)
D107 SMALL RIGHT DRAWER SIDE (1)
D108 SMALL LEFT DRAWER SIDE (1)
D109 SMALL DRAWER BACK (1)
D707 DRAWER BOTTOM (2)
E LEFT FRONT LEG (2)
F RIGHT REAR LEG (1)
G CENTER REAR LEG (1)
H UPPER UPRIGHT (1)
I LOWER UPRIGHT (1)
J ADJUSTABLE SHELF (1)
K END MOLDING (3)
L LARGE DRAWER FRONT (1)
M SMALL DRAWER FRONT (1)
N BOTTOM (1)
O SHELF (1)
P DOOR (1)
Q BACK (1)
R PURSE SHELF (1)
S MODESTY PANEL (1)
T TOP (1)
D28
D29
D78
D707
D707
L
D107
D108
D109
M
A
B
C
E
E
F
G
D
D
H
I
J
K
K
K
T
N
O
P
Q
S
R
422194www.sauder.com/services Page 3

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
HALF GROMMET - 2
67P
40CA CABINET RIGHT - 1 40CB CABINET LEFT - 1 40CC DRAWER RIGHT - 1 40CD DRAWER LEFT - 1
FILE GLIDE - 2
15B
EXTENSION SLIDE - 2
40MC
EXTENSION RAIL - 2
40MA
(EXTENSION SET SHOWN SEPARATED)
GROMMET CAP - 1
1P
CAM COVER - 18
12P
7F TWIST-LOCK®
FASTENER - 25
METAL PIN - 6
1R
29M BUMPER CARD - 1
PULL - 2
7K
10A SLIDE CAM - 4
22H
HINGE SPACER - 2
CAM SCREW - 22
8F
KNOB - 1
24K
WOOD DOWEL - 8
15F
GROMMET - 2
10P
HIDDEN CAM - 22
1F
RUBBER SLEEVE - 4
2R
14H HINGE - 2
422194 www.sauder.com/servicesPage 4

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
BLACK 1-1/8" MACHINE SCREW - 1
21S
SILVER 3/4" MACHINE SCREW - 4
20S3S GOLD 5/16" FLAT HEAD SCREW - 16
SILVER 5/8" FLAT HEAD SCREW - 4
23S
BLACK 9/16" FLAT HEAD SCREW - 6
32S
BLACK 1-15/16" FLAT HEAD SCREW - 10
113S
30S BLACK 1-9/16" FLAT HEAD SCREW - 8
422194www.sauder.com/services Page 5

Step 1 Look for this icon. It means a
video assembly tip is available at
www.sauder.com/services/tips
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å To begin assembly, push a SAUDER TWIST-LOCK®
FASTENER (7F) into the large holes in the MODESTY
PANEL (S) and PURSE SHELF (R). Repeat this step for
the ENDS (A and B), UPRIGHT (C), LOWER UPRIGHT (I),
SHELF (O), and BACK (Q).
Do not tighten the TWIST-LOCK® FASTENERS in this step.
(25 used)
7F
R
S
422194 www.sauder.com/servicesPage 6
7F
7F
7F

Step 2
Arrow
The arrow in the HIDDEN
CAM must point toward the
hole in the edge of the board.
Hole
å Push twenty-two HIDDEN CAMS (1F) into the ENDS (A and B),
UPRIGHT (C), and BACK (Q).
1F
Arrow
A
B
Q
C
Arrow
1F
(22 used)
422194www.sauder.com/services Page 7

Step 3
D
D
E
E
F
G
8F 8F
å Turn twenty-two CAM SCREWS (8F) into
the LEGS (D, E, F, and G).
8F
(22 used)
422194 www.sauder.com/servicesPage 8
Remember:
Righty tighty.
Lefty loosey.

Step 4
B
å Turn two BLACK 9/16" FLAT HEAD SCREWS (32S) into
the LEFT END (B) until the shoulders of the SCREWS rest
on the surfaces of the END.
å NOTE: Do not overtighten the SCREWS.
å Slide the END MOLDING (K) onto the LEFT END (B). Line
up the grooves in the MOLDINGS over the heads of the
SCREWS in the END .
å NOTE: The MOLDING should be even on both edges of
the ENDS
å NOTE: If the MOLDING comes up o of the SCREWS,
remove it and slide it on again.
BLACK 9/16" FLAT HEAD SCREW
(2 used in this step)
32S
Shoulder
Apply pressure with your hands
as you guide the MOLDINGS over
the SCREWS and onto the ENDS.
Surface without TWIST-LOCK® FASTENERS
422194www.sauder.com/services Page 9
K

Step 5
B
D
E
These surfaces
should be even.
15F
15F
Angled edge
Angled edge
Edge with TWIST-LOCK®
FASTENERS
Surface with HIDDEN CAMS
å Insert two WOOD DOWELS (15F) into the LEGS (D and E).
å Fasten the LEFT END (B) to the LEGS (D and E). Tighten
six HIDDEN CAMS.
å NOTE: Be sure the WOOD DOWELS insert into the END.
1
2
422194 www.sauder.com/servicesPage 10