Sauder Briarbrook 430072 User manual

sauder.com
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
sauder.com
CONTACT US FIRST
BEFORE MAKING ANY RETURNS TO THE STORE.
sauder.com
CONTACT US FIRST
BEFORE MAKING ANY RETURNS TO THE RETAILER.
Visit sauder.com/service to order replacement parts, view video assembly tips, or chat with a live rep.
Prefer the phone? Give us a ring at 1-800-445-1527.
Customer Service is available Monday-Friday - 9 a.m. to 5:30 p.m. EST (except holidays)
Sauder.com
Share your journey!
English pg 1-36
Français pg 37-42
Español pg 43-48
Lot # 573431 09/24/21
Purchased: __________________
Computer Desk
Briarbrook Collection | Model 430072
The original desktop.

Part Identification
Hardware Identification
Hardware Usage Guide
Assembly Steps
Français
Español
Safety
Warranty
Table of Contents Assembly Tools Required
2-3
4-5
6
6-36
37-42
43-48
49-50
51
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Page 2 www.sauder.com/service 430072
Electric drill with 1/8" or 3/8" bit
(ONLY in indicated step)
Pencil
Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
A TOP (1)
B BOTTOM (2)
C LEFT END (1)
D LEFT UPRIGHT (1)
E RIGHT UPRIGHT (1)
F RIGHT END (1)
G BACK (2)
H MODESTY PANEL (1)
J KEYBOARD SHELF (1)
K SMALL DRAWER FRONT (2)
L LARGE DRAWER FRONT (2)
M SMALL LEFT DRAWER SIDE (2)
N SMALL RIGHT DRAWER SIDE (2)
O SMALL DRAWER BACK (2)
P LARGE LEFT DRAWER SIDE (2)
Q LARGE RIGHT DRAWER SIDE (2)
S LARGE DRAWER BOTTOM (2)
U KEYBOARD FRONT (1)
V SMALL DRAWER BOTTOM (2)
W RIGHT END FRAME (1)
X BOTTOM BRACE (1)
Y TOP BRACE (1)
Z LEFT END FRAME (1)
CC LARGE DRAWER BACK (2)

Part Identification Now you know
our ABCs.
Page 3www.sauder.com/service430072
A
B
C
D
E
F
G
H
J
K
L
M
NO
P
Q
CC
S
V
W
Y
Z
G
B
K
L
M
NO
P
Q
CC
S
V
X
U

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
Page 4 www.sauder.com/service 430072
L-WRENCH - 1
16
APPLIQUE CARD - 1
15
GROMMET - 1
14
LARGE WOOD
DOWEL - 26
9
SMALL WOOD
DOWEL - 8
10 PULL - 4 1211 HINGE - 2
1LONG EXTENSION
RAIL - 4 2LONG EXTENSION SLIDE - 4
HIDDEN
CAM - 26
7CAM
SCREW - 26
8
6FILE BAR - 4
5FILE GLIDE - 4
(EXTENSION SET SHOWN SEPARATED)
3SHORT EXTENSION
RAIL - 6 4SHORT EXTENSION SLIDE - 6
(EXTENSION SET SHOWN SEPARATED)
FELT PAD CARD - 1
13
CORD CLIP - 2
25

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
1/2" HEX HEAD SCREW - 17
24
BLACK 1/2" FLAT HEAD SCREW - 60
23
Page 5www.sauder.com/service430072
1/2" PAN HEAD SCREW - 8
22
SILVER 9/16" FLAT HEAD SCREW - 8
21
1-7/8" HEX HEAD SCREW - 4
17
1-3/16" HEX HEAD SCREW - 2
19 1-3/16" FLAT HEAD SCREW - 16 20
1-9/16" PAN HEAD SCREW - 12
18
HIDDEN WIRELESS Qi COMPATIBLE
CHARGER by EGGTRONIC - Item 425905
(sold separately)
p
o
w
e
r
e
d
b
y
E
G
G
T
R
O
N
I
C
p
o
w
e
r
e
d
b
y
E
G
G
T
R
O
N
I
C
p
o
w
e
r
e
d
b
y
E
G
G
T
R
O
N
I
C
p
o
w
e
r
e
d
b
y
E
G
G
T
R
O
N
I
C

Hardware Usage Guide
HOW TO USE A HIDDEN CAM & CAM SCREW OR CAM DOWEL
NOTE: Various CAM SCREWS or a CAM DOWEL may be used.
Cam Screws Cam Dowel
Turn the CAM SCREW or
gently tap the CAM DOWEL
until the shoulder is against
the surface of the part.
1.
Hidden Cam
Arrow
Push a HIDDEN CAM into
the part. The arrow in the
HIDDEN CAM must point
toward the hole in the
edge of the board.
Hole
2.
3.
1
2
Insert the CAM SCREW or CAM DOWEL into the
HIDDEN CAM. Tighten the HIDDEN CAM.
Page 6 www.sauder.com/service 430072

Step 1
å Assemble your unit on a carpeted floor or on the empty carton to avoid
scratching your unit or the floor.
å Turn ten CAM SCREWS (8) into the exact holes shown in the TOP (A).
å Fasten the tabs on the TOP BRACE (Y) to the TOP (A). Tighten three
1/2" HEX HEAD SCREWS (24) using the L-WRENCH (16).
Look for this icon. It means a video assembly tip is
available at www.sauder.com/service/tips
Find the numbered video or scan the QR code.
Page 7www.sauder.com/service430072
1
16
8
(10 used)
A
Y
A
These two large
holes must be here.
1/2" HEX HEAD SCREW
(3 used in this step)
24

å Push two HIDDEN CAMS (7) into the MODESTY PANEL (H).
å Insert two LARGE WOOD DOWELS (9) into the TOP (A).
å Fasten the MODESTY PANEL (H) to the TOP (A). Tighten
two HIDDEN CAMS.
å NOTE: Be sure the WOOD DOWELS in the TOP insert into
the MODESTY PANEL.
Step 2
Page 8 www.sauder.com/service 430072
Surface with HIDDEN CAMS
A
H
H
9
1
Arrow
7
Some assembly
(and snacks) required.

Step 3
Page 9www.sauder.com/service430072
7
E
F
E
å 1st - Separate three SHORT EXTENSION SLIDES (4) from three SHORT EXTENSION RAILS (3) as shown in the
upper diagram below. Be prepared, the parts are greasy.
å 2nd - Fasten one SHORT EXTENSION RAIL (3) to the surface of the RIGHT UPRIGHT (E) as shown. Use three
BLACK 1/2" FLAT HEAD SCREWS (23).
å NOTE: For each EXTENSION RAIL, turn a SCREW into the hole shown in the enlarged diagram. Then, slide the
inner cartridge of the EXTENSION RAIL in to find the other holes that line up with the holes in the UPRIGHT.
Turn a SCREW into these holes.
å NOTE: The SHORT EXTENSION SLIDES will be used later for the SMALL DRAWERS and KEYBOARD SHELF.
å 3rd - Carefully flip the RIGHT UPRIGHT (E) over.
å 4th - Fasten two SHORT EXTENSION RAILS (3) to the RIGHT UPRIGHT (E) and RIGHT END (F) as shown. Use
six BLACK 1/2" FLAT HEAD SCREWS (23).
Open end
3
3
3
Open end
This hole
must be here.
This hole
must be here.
Open end
The notch
must be here.
F
L
I
P
O
V
E
R
3rd
4th
4 3
Push the black lever and pull the SLIDE from the RAIL.
Use these holes.
1st
2nd
4th
Surface with
fewer holes
BLACK 1/2" FLAT HEAD SCREW
(9 used in this step)
23

Step 4
Page 10 www.sauder.com/service 430072
7
å 1st - Push four HIDDEN CAMS (7) into the RIGHT UPRIGHT (E) and RIGHT END (F).
å 2nd - Separate two LONG EXTENSION SLIDES (2) from two LONG EXTENSION RAILS (1) as
shown in the upper diagram below. Be prepared, the parts are greasy.
å 3rd - Fasten two LONG EXTENSION RAILS (1) to the RIGHT UPRIGHT (E) and RIGHT END (F)
as shown. Use six BLACK 1/2" FLAT HEAD SCREWS (23).
å NOTE: For each EXTENSION RAIL, turn a SCREW into the hole shown in the enlarged
diagram. Then, slide the inner cartridge of the EXTENSION RAIL in to find the other holes that
line up with the holes in the UPRIGHT and END. Turn a SCREW into these holes.
å NOTE: The LONG EXTENSION SLIDES will be used later for the LARGE DRAWERS.
3rd
1st
7
Arrow
Arrow
7
E
F
1st
2 1
Push the black lever and pull the SLIDE from the RAIL.
Use these holes.
2nd
3rd
1
1
Open end
The notch
must be here.
BLACK 1/2" FLAT HEAD SCREW
(6 used in this step)
23