Sauder Orchard Hills 401346 User manual

NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
English pg 1-24
Français pg 25-28
Español pg 29-32
Lot # 364443 09/24/14
Purchased: __________________
Be sure to give us a ring before
making any returns. 1-800-523-3987
Entertainment Credenza
Orchard Hills Collection | 401346
Need help? Visit Sauder.com to view video assembly tips or chat with a live rep.
Prefer the phone? Call 1-800-523-3987.
Share your journey!
sauder.com
Entertaining what
entertains you.

Table of Contents Assembly Tools Required
3
4-5
6-24
25-28
29-32
33-34
35
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Use of a TV that is too heavy or large is hazardous. A TV that is too heavy will create a risk of a tip-over that can cause severe injury or
death. A TV that is too large for the available space might be accidentally pushed or bumped o the furniture, or subject to tip-over.
• Check the size and weight of your TV. Compare it to the diagram below – before you begin assembly!
• This Sauder unit is designed for use with televisions weighing less than 240 pounds. Never use with a TV that weighs more.
• The size of the television, front-to-back and side-to-side, must fit within the space defined in the diagram.
• Never place the front edge of the TV past the front edge of the TV support shelf (or stop molding – if equipped)
• Never allow the sides of the TV to extend past the side edges of the TV support surface.
• If the TV has a CRT picture tube, the picture tube cone may extend past the rear of the support shelf.
• Be sure to apply the warning label as instructed in the last assembly step. The label provides important safety related information.
WARNING
!
240 lbs.
240 lbs.
21"
21"
59-3/4"
59-3/4"
Skip the power trip.
This time.
401346 www.sauder.com/servicesPage 2
Straight Edge Screwdriver

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
A RIGHT END (1)
B LEFT END (1)
C RIGHT UPRIGHT (1)
D LEFT UPRIGHT (1)
E CENTER UPRIGHT (1)
F TOP (1)
G SHELF (2)
H LARGE ADJUSTABLE SHELF (2)
I SMALL ADJUSTABLE SHELF (2)
J2 BOTTOM (1)
K BACK (1)
L RIGHT DOOR (1)
M LEFT DOOR (1)
N DRAWER FRONT (2)
S FRONT MOLDING (1)
T RIGHT MOLDING (1)
U LEFT MOLDING (1)
V FRONT SKIRT (1)
W SIDE SKIRT (2)
D65 DRAWER BACK (2)
D107 RIGHT DRAWER SIDE (2)
D108 LEFT DRAWER SIDE (2)
D962 DRAWER BOTTOM (2)
Now you know
our ABCs.
401346www.sauder.com/services Page 3
A
B
C
D
E
F
G
HI
J2
K
L
M
N
S
T
U
V
W
G
H
I
W
D962
D107
D65
D108

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
401346 www.sauder.com/servicesPage 4
(EXTENSION SET SHOWN SEPARATED)
EXTENSION RAIL - 4
XEXTENSION SLIDE - 4 YCENTER FOOT - 2
ZSIDE FOOT - 2
BB
QQ WARNING LABEL - 1
WARNING
Never use this furniture with a TV that is too
large or too heavy. Severe injury or death
can occur.The TV and furniture will be
unstable and may tip.
-The TV must less than 240 lbs.
-The base of the TV must be able to sit
completely on this shelf.
-Refer to instruction book for complete safety
information.
Note: This is a permanent label. Do not try
to remove. Surface will be damaged.
269336
(Refer to Step 15 for proper
location and application)
AAA CORNER CAP - 2 CORNER BRACKET - 2
BBB
ANGLE BRACKET - 3
CC HIDDEN CAM - 16
1F CAM DOWEL - 16 2F HINGE - 4 FF
BACKPLATE - 2
HH KNOB - 2
II HANDLE - 2
KK
HANDLE MOUNT - 4
JJ
MOLDING
CONNECTOR - 2
LL FELT DISC CARD - 1
MM NN SLIDE CAM - 4 METAL PIN - 18 OO
RUBBER SLEEVE - 16
PP

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
401346www.sauder.com/services Page 5
BLACK 1-7/8" FLAT HEAD SCREW - 10
RR SILVER 1-1/8" FLAT HEAD SCREW - 9 SS
BLACK 1-1/8" MACHINE SCREW - 2
TT
BLACK 1-1/8" PAN HEAD SCREW - 2
ZZ
UU SILVER 5/8" MACHINE SCREW - 4
GOLD 9/16" LARGE HEAD SCREW - 26
VV BLACK 9/16" WAFER HEAD SCREW - 2
WW
XX GOLD 5/16" FLAT HEAD SCREW - 16 NAIL - 46 YY
30S BLACK 1-9/16" FLAT HEAD SCREW - 8

Step 1 Look for this icon. It means a
video assembly tip is available at
www.sauder.com/services/tips
å Assemble your unit on a carpeted floor or on the
empty carton to avoid scratching your unit or the floor.
å Push sixteen HIDDEN CAMS (1F) into the ENDS (A
and B), UPRIGHTS (C and D), and SHELVES (G). Then,
insert the metal end of a CAM DOWEL (2F) into each
HIDDEN CAM.
401346 www.sauder.com/servicesPage 6
Arrow
1F
2F
(16 used)
Arrow
1F
2F
Do not tighten the HIDDEN CAMS in this step.
Insert the metal end of the CAM
DOWEL into the HIDDEN CAM.
Arrow
A
B
C
D
G
G

å Separate the EXTENSION SLIDES (Y) from the
EXTENSION RAILS (X) as shown in the diagram. Be
prepared, the parts are greasy.
å Fasten EXTENSION RAILS (X) to the parts as shown. Use
eight GOLD 5/16" FLAT HEAD SCREWS (XX).
å NOTE: For each EXTENSION RAIL, turn a SCREW into the
hole shown in the enlarged diagram. Then, slide the inner
cartridge of the EXTENSION RAIL in to find the other
hole that lines up with the hole in the UPRIGHTS. Turn a
SCREW into this hole.
Step 2
401346www.sauder.com/services Page 7
E
C
X
X
X
XGOLD 5/16" FLAT HEAD SCREW
(8 used in this step)
XX
XY
Push the release lever in and pull the SLIDE from the RAIL.
Finished edge
Finished edge
Surface without
HIDDEN CAMS
Open end
Finished edge
Open end
D
Surface without
HIDDEN CAMS
Open end
Remember:
Righty tighty.
Lefty loosey.

Step 3
å Tap the MOLDING CONNECTORS (LL) into the notches in
the MOLDINGS (S, T, and U).
401346 www.sauder.com/servicesPage 8
Flat end
Flat end
Use your hammer to tap the MOLDING CONNECTORS (LL) into the notches in the MOLDINGS.
LL
S
T
U
LL

å Fasten the TOP (F) to the MOLDINGS (S, T, and U). Use
nine SILVER 1-1/8" FLAT HEAD SCREWS (SS).
Step 4
401346www.sauder.com/services Page 9
S
T
U
F
Unfinished surface
Unfinished edge
SILVER 1-1/8" FLAT HEAD SCREW
(9 used in this step)
SS

Step 5
å Fasten the END (A) to the TOP (F). Tighten two
HIDDEN CAMS.
401346 www.sauder.com/servicesPage 10
Start Tighten
Arrow
Minimum
190 degrees
Caution
Risk of damage or
injury. HIDDEN CAMS
must be completely
tightened. HIDDEN
CAMS that are not
completely tightened
may loosen, and parts
may separate. To
completely tighten:
Arrow
Maximum
210 degrees
A
F
Surface without
HIDDEN CAMS
Surface with
more holes
Finished edge
Do not stand the unit upright without the
BACK fastened. The unit may collapse.
Caution
S