Sauder 411885 User manual

PLEASE CONTACT US
BEFORE RETURNING
YOUR UNIT TO THE STORE
1-800-523-3987
www.sauder.com
Made in the USA
Archbold, OH
NOTE: THIS INSTRUCTION BOOKLET CONTAINS
IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Lot #: 346761 09 / 25 / 12
Date Purchased: ____________________
English.................... Page 1-18
Français...............Pages 19-21
Espanol.............Páginas 22-24
411885
Night Stand

ASSEMBLY TOOLS REQUIRED
Hammer
No. 2 Phillips Screwdriver
Tip Shown Actual Size
TABLE OF CONTENTS
Part Identification.......................3
Hardware Identification .............4
Assembly Steps....................5-18
Français..............................19-21
Espanol...............................22-24
Safety .................................25-26
Warranty...................................27
Page 2 www.sauder.com/services 411885

PART IDENTIFICATION: While not all parts are labeled, some of the parts will have a label or an inked
letter on the edge to help distinguish similar parts from each other. Use this PART IDENTIFICATION to help
identify similar parts.
A RIGHT END 1
B LEFT END 1
C TOP 1
D BOTTOM 1
E BACK 1
F RIGHT FRONT LEG 1
G LEFT FRONT LEG 1
H BACK LEG 2
I DRAWER FRONT 1
J DRAWER BACK 1
K RIGHT DRAWER SIDE 1
L LEFT DRAWER SIDE 1
M DRAWER BOTTOM 1
N END MOLDING 2
Page 3
www.sauder.com/services411885
A
B
C
D
E
F
G
H
I
JK
L
M
N
H
N

HARDWARE IDENTIFICATION
Screws are shown actual size. You may receive extra hardware with your unit.
Page 4 www.sauder.com/services 411885
RIGHT CABINET
RAIL - 1
O Q RIGHT DRAWER
SLIDE - 1 RLEFT DRAWER SLIDE - 1
BLACK 1-1/8” MACHINE SCREW - 1
BB
BLACK 1-7/8" FLAT HEAD SCREW - 6
AA
HIDDEN CAM - 12
S2 CAM COVER - 2
V
CAM SCREW - 4
U2
GOLD 5/16" FLAT HEAD SCREW - 8
DD NAIL - 18 EE
BLACK 9/16" FLAT HEAD SCREW - 4
CC
SLIDE CAM - 2
XW CLIP - 2 TACK GLIDE - 4 Z
KNOB - 1
Y
LEFT CABINET
RAIL - 1
P
CAM DOWEL - 8
T2

1
1
S
t
e
p
Look for this icon. It means a video
assembly tip is available at:
www.sauder.com/services/tips
Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor.
Push twelve HIDDEN CAMS (S2) into the ENDS (A and B) and BOTTOM (D) as shown in the upper diagrams. Then, insert the
metal end of a CAM DOWEL (T2) into each HIDDEN CAM, except in the long edges of the ENDS (A and B).
Turn four CAM SCREWS (U2) into the FRONT LEGS (F and G) as shown in the lower right diagrams.
Page 5
www.sauder.com/services411885
Do not tighten the HIDDEN CAMS in this step.
(8 used)
(4 used)
Do not insert CAM
DOWELS into these holes.
Do not insert
CAM DOWELS
into this edge.
(12 used) A
B
F
G
D
U2
Insert the metal end of the CAM
DOWEL into the HIDDEN CAM.
Arrow
Arrow
S2
Arrow
S2
Arrow
T2
S2

Page 6 www.sauder.com/services 411885
2
2
S
t
e
p
Carefully turn over the ENDS (A and B) and position them as shown with the surface without HIDDEN CAMS facing up.
Fasten the BACK LEGS (H) to the ENDS (A and B). Use six BLACK 1-7/8" FLAT HEAD SCREWS (AA).
A
H
H
BLACK 1-7/8” FLAT HEAD SCREW
(6 used in this step)
AA
Angled edge
These edges
should be even.
Surface without
HIDDEN CAMS
B
Surface without
HIDDEN CAMS

Page 7
www.sauder.com/services411885
3
3
S
t
e
p
Turn four BLACK 9/16” FLAT HEAD SCREWS (CC) into the ENDS (A and B) until the shoulder of the SCREWS rest on the surface
of the ENDS.
Slide the END MOLDINGS (N) onto the ENDS (A and B). Line up the groove in the MOLDINGS over the head of the SCREWS in
the ENDS.
Apply pressure with your hands as
you guide the MOLDINGS over
the SCREWS and onto the ENDS.
Shoulder
A
B
N
N
These edges
should be even. BLACK 9/16" FLAT HEAD SCREW
(4 used in this step)
CC
These edges
should be even.

Page 8 www.sauder.com/services 411885
4
4
S
t
e
p
Carefully turn over the ENDS (A and B) and position them as shown with the surface with HIDDEN CAMS facing up.
Fasten the FRONT LEGS (F and G) to the ENDS (Aand B). Tighten four HIDDEN CAMS.
B
G
F
Surface with
HIDDEN CAMS
A
Surface with
HIDDEN CAMS
Angled edge
Angled edge
These edges
should be even.

Page 9
www.sauder.com/services411885
5
5
S
t
e
p
Fasten the CABINET RAILS (O and P) to the ENDS (Aand B). Use four GOLD 5/16” FLAT HEAD SCREWS (DD) through holes
1 and 3.
NOTE: The CABINET RAILS are marked "CABINET RIGHT" and "CABINET LEFT" for easy identification.
Roller end
GOLD 5/16” FLAT HEAD SCREW
(4 used in this step)
DD
1
3
O
P
B
A
Roller end
1
3

Page 10 www.sauder.com/services 411885
6
6
S
t
e
p
Fasten the LEFT END (B) to the TOP (C). Tighten two HIDDEN CAMS.
Fasten the BOTTOM (D) to the LEFT END (B). Tighten two HIDDEN CAMS.
B
C
D
Unfinished surface
Unfinished edge
Unfinished surface
Finished edge
Caution
Risk of damage or
injury. Hidden Cams
must be completely
tightened. Hidden
Cams that are not
completely tightened
may loosen, and parts
may separate.
To completely tighten:
Start Tighten
Arrow
Maximum
210 degrees
Minimum
190 degrees
Arrow