Sauder Hutch 404975 User manual

NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
English pg 1-19
Français pg 20-22
Español pg 23-25
Lot # 377190 09/29/15
Purchased: __________________
Be sure to give us a ring before
making any returns. 1-800-523-3987
Hutch
Heritage Hill Collection | Model 404975
Need help? Visit Sauder.com to view video assembly tips or chat with a live rep.
Prefer the phone? Call 1-800-523-3987.
Share your journey!
sauder.com
For things 'n such.

Table of Contents Assembly Tools Required
3
4
5-19
20-22
23-25
26
27
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Skip the power trip.
This time.
404975 www.sauder.com/servicesPage 2

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
A RIGHT END (1)
B LEFT END (1)
C RIGHT UPRIGHT (1)
D LEFT UPRIGHT (1)
E UPRIGHT (2)
F SMALL UPRIGHT (1)
G TOP (1)
H SHELF (1)
I SMALL SHELF (1)
J LARGE BACK (1)
K BACK (1)
L2 DOOR (2)
M ADJUSTABLE SHELF (2)
N2 VALANCE (1)
M69 SHELF MOLDING (1)
P END MOLDING (2)
Now you know
our ABCs.
404975www.sauder.com/services Page 3
A
BC
D
E
F
G
H
I
J
K
L2
M
P
PL2
M
E
M69
N2

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
404975 www.sauder.com/servicesPage 4
QTWIST-LOCK®FASTENER - 13 ANGLE BRACKET - 20
RSAFETY BRACKET - 1 S
SCREW COVER - 6
TFELT DISC CARD - 1 WMETAL PIN - 8 Z
RUBBER SLEEVE - 8
AA BACKPLATE - 2 HH
PULL - 2
GG
BLACK 1-7/8" FLAT HEAD SCREW - 19
BB BLACK 1-1/8" MACHINE SCREW - 2 CC
BLACK 9/16" LARGE HEAD SCREW - 53
DD
NAIL - 53
FF
SILVER 5/8" FLAT HEAD SCREW - 8
23S
22H
HINGE SPACER - 4
UHINGE - 4

Step 1 Look for this icon. It means a
video assembly tip is available at
www.sauder.com/services/tips
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å To begin assembly, push a SAUDER TWIST-LOCK®
FASTENER (Q) into the large holes in the RIGHT
UPRIGHT (C) and LEFT UPRIGHT (D).
å Repeat this step for the SMALL UPRIGHT (F), TOP (G),
and SHELF (H).
404975www.sauder.com/services Page 5
(13 used)
Q
Do not tighten the TWIST-LOCK® FASTENERS in this step.
C
D

Step 2
å Fasten eighteen ANGLE BRACKETS (R) to the ENDS (A
and B), TOP (G), and SHELF (H). Use eighteen BLACK
9/16" LARGE HEAD SCREWS (DD).
å NOTE: Be sure the edges of the ANGLE BRACKETS are
even with the edges of the ENDS, TOP, and SHELF.
404975 www.sauder.com/servicesPage 6
A
B
H
G
R
(18 used)
BLACK 9/16" LARGE HEAD SCREW
(18 used in this step)
DD
R
R

å Fasten the TOP (G) to the LEFT END (B). Tighten two
TWIST-LOCK® FASTENERS.
å Fasten the UPRIGHTS (E) to the TOP (G). Use four BLACK
1-7/8" FLAT HEAD SCREWS (BB).
Step 3
404975www.sauder.com/services Page 7
How to use the SAUDER TWIST-LOCK®FASTENER
1. Insert the dowel end of the FASTENER into the hole of the
adjoining part.
NOTE: The dowel end of the FASTENER must remain fully
inserted in the hole of the adjoining part while locking
the FASTENER.
2. Tighten the FASTENER with a Phillips screwdriver as tight
as possible.
Dowel end
B
G
E
E
BLACK 1-7/8" FLAT HEAD SCREW
(4 used for the UPRIGHTS)
BB
Finished edge
Surface without
TWIST-LOCK®
FASTENERS
Edge with ANGLE BRACKETS
Finished edge
Do not stand the unit upright without the
BACK fastened. The unit may collapse.
Caution

Step 4
å Fasten the SHELF (H) to the LEFT END (B). Tighten two
TWIST-LOCK® FASTENERS.
å Fasten the SHELF (H) to the UPRIGHTS (E). Use four
BLACK 1-7/8" FLAT HEAD SCREWS (BB).
å Now, fasten the SHELF MOLDING (M69) to the SHELF (H).
Use five BLACK 9/16" LARGE HEAD SCREWS (DD).
404975 www.sauder.com/servicesPage 8
BLACK 9/16" LARGE HEAD SCREW
(5 used for the SHELF MOLDING)
DD
B
E
E
Surface with
TWIST-LOCK®
FASTENERS
H
Edge with ANGLE BRACKETS
BLACK 1-7/8" FLAT HEAD SCREW
(4 used for the UPRIGHTS)
BB
These edges should be even.
M69

å Fasten the UPRIGHTS (C, D, and F) to the SHELF (H).
Tighten five TWIST-LOCK® FASTENERS.
Step 5
404975www.sauder.com/services Page 9
Surface with
TWIST-LOCK®
FASTENERS
H
D
Surface without
TWIST-LOCK® FASTENERS
C
F
Finished edge

Step 6
å Fasten the RIGHT END (A) to the TOP (G) and SHELF (H).
Tighten four TWIST-LOCK® FASTENERS.
å Fasten the SMALL SHELF (I) to the UPRIGHTS (C, D,
and F). Use six BLACK 1-7/8" FLAT HEAD SCREWS (BB).
404975 www.sauder.com/servicesPage 10
H
BLACK 1-7/8" FLAT HEAD SCREW
(6 used in this step)
BB
DI
C
G
A
Finished edge
Finished edge
F