Sauder Edge Water Lift-Top Coffee Table 414856 User manual

Need help? Visit Sauder.com to view video assembly tips or chat with a live rep.
Prefer the phone? Call 1-800-523-3987.
Share your journey!
sauder.com
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
English pg 1-19
Français pg 20-22
Español pg 23-25
Lot # 389175 02/24/16
Purchased: __________________
Be sure to give us a ring before
making any returns. 1-800-523-3987
Lift-Top Coee Table
Edge Water Collection | 414856
Guaranteed to hold
other beverages, too.

Table of Contents Assembly Tools Required
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Skip the power trip.
This time.
3
4
5-19
20-22
23-25
26
27
Adjustable Wrench
414856 www.sauder.com/servicesPage 2

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
A RIGHT END (1)
B LEFT END (1)
C UPRIGHT (2)
D TOP (1)
E BOTTOM (1)
F SHELF (1)
G PANEL (2)
H2 RIGHT FRONT/LEFT REAR LEG (2)
I2 LEFT FRONT/RIGHT REAR LEG (2)
J STRETCHER (1)
K FOOT SPACER (2)
L SKIRT (2)
M FOOT (4)
414856www.sauder.com/services Page 3
A
B
C
D
E
F
G
H2
I2
J
K
L
H2
I2
L
G
C
M
M
M
M

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
414856 www.sauder.com/servicesPage 4
PLASTIC FOOT - 2
23E
23M LIFT TABLE
MECHANISM SET - 1
SUPPORT BRACKET - 2
37G
HIDDEN CAM - 36
1F CAM DOWEL - 14 2F
BUMPER - 6
2M
BLACK 1-7/8" FLAT HEAD SCREW - 4
2S
BLACK 9/16" LARGE HEAD SCREW - 16
1S
CAM COVER - 18
12P
BROWN 1" FLAT HEAD SCREW - 4
12S
BLACK 3/4” MACHINE SCREW - 4
92S BLACK 1-1/4" MACHINE SCREW - 4 93S
NUT - 8
24M
WASHER - 8
13M
CAM SCREW - 22
20F
METAL PIN - 4
1R
16S BLACK 1-7/8" PAN HEAD SCREW - 4 BLACK 3/4" PAN HEAD SCREW - 2
85S
BUSHING - 2
91M

Step 1 Look for this icon. It means a
video assembly tip is available at
www.sauder.com/services/tips
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å Push thirty-six HIDDEN CAMS (1F) into the ENDS (A and B),
BOTTOM (E), SHELF (F), PANELS (G), and SKIRTS (L). Then,
insert the metal end of a CAM DOWEL (2F) into each HIDDEN
CAM in the short edges of the BOTTOM (E) and SHELF (F).
414856www.sauder.com/services Page 5
E
F
A
B
G
L
L
G
(36 used)
(14 used)
Arrow
1F
2F
Do not tighten the HIDDEN CAMS in this step.
Do not insert CAM DOWELS into these edges.
Insert the metal end of the CAM
DOWEL into the HIDDEN CAM.
Arrow
Arrow
1F
1F
Arrow
1F
Arrow
Do not insert CAM DOWELS into these parts.
Scan this QR code or go to this address:
http://qr.sauder.com/?ID=1440
to watch a video on how to assemble your unit.

Step 2
414856 www.sauder.com/servicesPage 6
å Turn twenty-two CAM SCREWS (20F) into the LEGS (H2
and I2) and SKIRTS (L).
20F
20F
L
L
H2
I2
H2
I2
(22 used)

å Fasten the LEGS (H2 and I2) to the ENDS (A and B).
Tighten eight HIDDEN CAMS.
å Fasten four FEET (M) to the LEGS (H2 and I2). Use four
BLACK 1-7/8" PAN HEAD SCREWS (16S).
Step 3
414856www.sauder.com/services Page 7
Remember:
Righty tighty.
Lefty loosey.
H2
I2
H2
I2
A
BM
M
M
M
Surface with
HIDDEN CAMS Surface with
HIDDEN CAMS
12
These edges
must be even.
These edges
must be even. Smaller
hole
Smaller
hole
Smaller
hole
Smaller
hole
BLACK 1-7/8" PAN HEAD SCREW
(4 used in this step)
16S

å Fasten the SHELF (F) to the PANELS (G). Tighten six
HIDDEN CAMS.
Step 4
414856 www.sauder.com/servicesPage 8
Start Tighten
Arrow
Minimum
190 degrees
Caution
Risk of damage or
injury. HIDDEN CAMS
must be completely
tightened. HIDDEN
CAMS that are not
completely tightened
may loosen, and parts
may separate. To
completely tighten:
Arrow
Maximum
210 degrees
F
G
G
Surface with
HIDDEN CAMS
Surface without
HIDDEN CAMS
Surface with HIDDEN CAMS
Holes on the other surface
are closer to this edge.
Holes are closer to this edge.

å Fasten the SKIRTS (L) to the BOTTOM (E). Tighten six
HIDDEN CAMS.
Step 5
414856www.sauder.com/services Page 9
E
L
L
Surface with
HIDDEN CAMS
Surface with CAM SCREWS
Surface without CAM SCREWS
Flat edge
Flat edge
The bottom edges
should be even.

å Fasten the BOTTOM (E) to the UPRIGHTS (C). Use four
BLACK 1-7/8"FLAT HEAD SCREWS (2S).
Step 6
414856 www.sauder.com/servicesPage 10
BLACK 1-7/8" FLAT HEAD SCREW
(4 used in this step)
2S
E
C
C
Edge with
smaller holes
Edge with
smaller holes
Surface with
HIDDEN CAMS