Sauder 414141 User manual

PLEASE CONTACT US
BEFORE RETURNING
YOUR UNIT TO THE STORE
1-800-523-3987
www.sauder.com
Made in the USA
Archbold, OH
NOTE: THIS INSTRUCTION BOOKLET CONTAINS
IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
English.................... Page 1-28
Français...............Pages 29-32
Espanol.............Páginas 33-36
Lot #: 348404 02 / 22 / 13
Date Purchased: ____________________
414141
Desk

ASSEMBLY TOOLS REQUIRED
Hammer
No. 2 Phillips Screwdriver
Tip Shown Actual Size
ADULT ASSEMBLY REQUIRED
TABLE OF CONTENTS
Part Identification...................2-3
Hardware Identification .............4
Assembly Steps....................5-28
Français..............................29-32
Espanol...............................33-36
Safety .................................37-38
Warranty...................................39
D116
D116
D112
D112
D102
D102
D113
D113
D113 D114
D114
D113
D722
D713
D713
K
O
QV
W
Page 2 www.sauder.com/services 414141

PART IDENTIFICATION: While not all parts are labeled, some of the parts will have a label or an inked
letter on the edge to help distinguish similar parts from each other. Use this PART IDENTIFICATION to help
identify similar parts.
A RIGHT END 1
B LEFT END 1
C UPRIGHT 1
D TOP 1
E BOTTOM 2
F MODESTY PANEL 1
G SHELF 1
H BACK 1
ILEFT FRONT/RIGHT
BACK LEG 3
JRIGHT FRONT/LEFT
BACK LEG 3
KSMALL DRAWER
FRONT 1
OLARGE DRAWER
FRONT 1
QPENCIL DRAWER
FRONT 1
T SKIRT 1
U LOWER END MOLDING 3
VPENCIL DRAWER
MOLDING 1
W DRAWER MOLDING 1
X EXTENSION BLOCK 1
D102 LARGE DRAWER SIDE 2
D112 LARGE DRAWER
FRONT/BACK 2
D113 DRAWER SIDE 4
D114 SMALL DRAWER
FRONT/BACK 2
D116 PENCIL DRAWER
FRONT/BACK 2
D713 DRAWER BOTTOM 2
D722 LARGE DRAWER
BOTTOM 1
A
B
C
D
E
E
F
G
H
I
I
I
J
J
J
T
U
U
U
X
Page 3
www.sauder.com/services414141

HARDWARE IDENTIFICATION
Screws are shown actual size. You may receive extra hardware with your unit.
ZEXTENSION SLIDE - 2
YEXTENSION RAIL - 2
(EXTENSION SET SHOWN SEPARATED)
FILE GLIDE - 2
3B
HIDDEN CAM - 36
1F CAM SCREW - 18 8F
BLACK 1-7/8" FLAT HEAD SCREW - 7
2S
GOLD 5/16" FLAT HEAD SCREW - 24
3S
KNOB - 3
61K
BLACK 1-5/8" PAN HEAD SCREW - 3
27S
BLACK 9/16" LARGE HEAD SCREW - 4
1S
METAL PIN - 4
1R
CAM DOWEL - 18
2F
BLACK 9/16" FLAT HEAD SCREW - 6
32S
BLACK 1-1/4" FLAT HEAD SCREW - 2
7S
NAIL - 25
1N
BLACK 7/8" LARGE HEAD SCREW - 10
17S
CAM COVER - 5
32P
19G LARGE METAL BRACKET - 2
40CB CABINET LEFT - 2
40CA CABINET RIGHT - 2
40CC DRAWER RIGHT - 2 40CD DRAWER LEFT - 2
Page 4 www.sauder.com/services 414141
BLACK 1-9/16" FLAT HEAD SCREW - 24
30S

Look for this icon. It means a video
assembly tip is available at:
www.sauder.com/services/tips
1
1
S
t
e
p
Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor.
Push thirty-six HIDDEN CAMS (1F) into the ENDS (A and B), UPRIGHT (C), BOTTOMS (E), MODESTY PANEL (F) and SHELF (G). Then,
insert the metal end of a CAM DOWEL (2F) into each HIDDEN CAM, except the long edges of the ENDS ( A and B) and UPRIGHT (C).
Do not tighten the HIDDEN CAMS in this step.
Arrow
Arrow
Arrow
Arrow
Arrow
1F
1F
1F
1F
2F
2F
2F
2F
Insert the metal end of the CAM
DOWEL into the HIDDEN CAM.
Arrow
A
B
C
F
G
E
E
Do not insert CAM DOWELS into these edges.
Arrow
(18 used)
(36 used)
Page 5
www.sauder.com/services414141

2
2
S
t
e
p
Turn eighteen CAM SCREWS (8F) into the LEGS (I and J).
8F (18 used)
I
I
I
J
J
J
Page 6 www.sauder.com/services 414141

3
3
S
t
e
p
Fasten two LEFT FRONT LEGS (I) to the LEFT END (B) and UPRIGHT (C). Tighten six HIDDEN CAMS.
Fasten a RIGHT FRONT LEG (J) to the RIGHT END (A). Tighten three HIDDEN CAMS.
B
C
A
J
I
I
These edges
should be even.
These edges
should be even.
Surface with
HIDDEN CAMS
Surface with
HIDDEN CAMS
Surface with
HIDDEN CAMS
Page 7
www.sauder.com/services414141

Flip the ENDS (A and B) and UPRIGHT (C) over onto their opposite surface.
Turn six BLACK 9/16" FLAT HEAD SCREWS (32S) into the ENDS (A and B ) and UPRIGHT (C) until the shoulder of the
SCREWS rest on the surface of each one.
Slide the LOWER END MOLDINGS (U) onto the ENDS and UPRIGHT. Line up the groove in the MOLDINGS over the head of the
SCREWS in the ENDS and UPRIGHT.
4
4
S
t
e
p
B
C
A
Apply pressure with your hands as
you guide the MOLDINGS over
the SCREWS and onto the ENDS.
Shoulder
These edges
should be even.
These edges
should be even.
These edges
should be even.
BLACK 9/16" FLAT HEAD SCREW
(6 used in this step)
32S
Page 8 www.sauder.com/services 414141
U
U
U

Flip the ENDS (A and B) and UPRIGHT (C) over onto their opposite surface.
Fasten two RIGHT FRONT/LEFT BACK LEGS (J) to the LEFT END (B) and UPRIGHT (C). Tighten six HIDDEN CAMS.
Fasten a LEFT FRONT/RIGHT BACK LEG (I) to the RIGHT END (A). Tighten three HIDDEN CAMS.
5
5
S
t
e
p
B
C
A
J
J
I
Surface with
HIDDEN CAMS
Surface with
HIDDEN CAMS
Surface with
HIDDEN CAMS
Page 9
www.sauder.com/services414141
These edges
should be even.
These edges
should be even.

6
6
S
t
e
p
Surface with
HIDDEN CAMS Surface with
HIDDEN CAMS
C
A
Separate the EXTENSION SLIDES (Z) from the EXTENSION RAILS (Y) as shown in the upper diagram. Be prepared, the parts are
greasy.
Fasten an EXTENSION RAIL (Y) to the RIGHT END (A) and UPRIGHT (C). Use four GOLD 5/16" FLAT HEAD SCREWS (3S).
NOTE: For each EXTENSION RAIL, turn a SCREW into the hole shown in the enlarged diagram. Then, slide the inner
cartridge of the EXTENSION RAIL in to find the other hole that lines up with the hole in the END and UPRIGHT. Turn a SCREW
into this hole.
Push the black lever in and pull the SLIDE from the RAIL.
GOLD 5/16" FLAT HEAD SCREW
(4 used in this step)
3S
Open end
Open end
Y
Y
Y
Z
Edge with CAM DOWELS
Page 10 www.sauder.com/services 414141