Sauder Clifford Place 433360 User manual

sauder.com
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
sauder.com
CONTACT US FIRST
BEFORE MAKING ANY RETURNS TO THE STORE.
sauder.com
CONTACT US FIRST
BEFORE MAKING ANY RETURNS TO THE RETAILER.
Visit sauder.com/service to order replacement parts, view video assembly tips, or chat with a live rep.
Prefer the phone? Give us a ring at 1-800-445-1527.
Customer Service is available Monday-Friday - 9 a.m. to 5:30 p.m. EST (except holidays)
Sauder.com
Share your journey!
English pg 1-28
Français pg 29-32
Español pg 33-36
Lot # 576876 01/13/22
Purchased: __________________
Library Base
Cliord Place Collection | Model 433360
The stories of your life.

Part Identification
Hardware Identification
Hardware Usage Guide
Assembly Steps
Français
Español
Safety
Warranty
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Table of Contents Assembly Tools Required
3
4
5
6-28
29-32
33-36
37-38
39
Page 2 www.sauder.com/service 433360

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
Page 3www.sauder.com/service433360
A RIGHT END (1)
B LEFT END (1)
C TOP (1)
D TOP MOLDING (1)
E UPPER BACK (1)
F BRACE (1)
G ADJUSTABLE SHELF (1)
H LOWER BACK (1)
I BOTTOM (1)
J BOTTOM MOLDING (2)
K LEFT DRAWER SIDE (1)
L DRAWER BACK (1)
M RIGHT DRAWER SIDE (1)
N DRAWER BOTTOM (1)
O DRAWER BRACE (1)
P DRAWER FRONT (1)
Q LEFT DOOR (1)
R RIGHT DOOR (1)
S FOOT (4)
A
B
C
D
E
F
G
H
I
J
J
K
LM
N
O
S
S
S
S
P
QR

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
ANGLED HEAD
CAM SCREW - 20
2
Angled head
LARGE HIDDEN
CAM - 20
1
SILVER 1/2" FLAT HEAD SCREW - 14
19 BLACK 1/2" PAN HEAD SCREW - 12
20
WOOD
DOWEL - 22
6SHORT WOOD
DOWEL - 6
7
LONG WOOD
DOWEL - 4
5
SMALL HIDDEN
CAM - 6
3STRAIGHT HEAD
CAM SCREW - 6
4
Straight head
METAL PIN - 4
15 RUBBER
SLEEVE - 4
16
SMALL APPLIQUE
CARD - 1
13 LARGE APPLIQUE
CARD - 1
14
ADJUSTABLE
GLIDE - 4
10 HINGE
BRACKET - 4
11 HINGE - 4 12
GROMMET
WITH CAP- 1
9
PULL - 3
8
BLACK 1-1/2" FLAT HEAD SCREW - 8
17 BLACK 1-1/8" FLAT HEAD SCREW - 9 18
Page 4 www.sauder.com/service 433360
(EXTENSION SET SHOWN SEPARATED)
TEXTENSION RAIL - 2 UEXTENSION SLIDE - 2

Hardware Usage Guide
HOW TO USE A HIDDEN CAM & CAM SCREW OR CAM DOWEL
NOTE: Various CAM SCREWS or a CAM DOWEL may be used.
Cam Screws Cam Dowel
Turn the CAM SCREW or
gently tap the CAM DOWEL
until the shoulder is against
the surface of the part.
1.
Hidden Cam
Arrow
Push a HIDDEN CAM into
the part. The arrow in the
HIDDEN CAM must point
toward the hole in the
edge of the board.
Hole
2.
3.
1
2
Insert the CAM SCREW or CAM DOWEL into the
HIDDEN CAM. Tighten the HIDDEN CAM.
Page 5www.sauder.com/service433360

Step 1 Look for this icon. It means a video assembly tip is
available at www.sauder.com/service/tips
Find the numbered video or scan the QR code.
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å Push two LARGE HIDDEN CAMS (1) into the RIGHT END (A).
å Turn seven ANGLED HEAD CAM SCREWS (2) into the exact
holes shown in the RIGHT END (A).
å Fasten two HINGE BRACKETS (11) to the RIGHT END (A)
exactly as shown. Use the SCREWS in the brackets.
Page 6 www.sauder.com/service 433360
Remember:
Righty tighty.
Lefty loosey.
Arrow
1
Angled head
2
A
A
11
1

Step 2
Page 7www.sauder.com/service433360
A
å Separate the EXTENSION SLIDES (U) from the EXTENSION RAILS (T) as shown in the enlarged diagram
below. Be prepared, the parts are greasy.
å Fasten one EXTENSION RAIL (T) to the RIGHT END (A). Use three BLACK 1/2" PAN HEAD SCREWS (20).
å NOTE: For the EXTENSION RAIL, turn a SCREW into the hole shown in the enlarged diagram. Then, slide
the inner cartridge of the EXTENSION RAIL in to find the other holes that line up with the holes in the END.
Turn a SCREW into those holes.
å NOTE: The EXTENSION SLIDES will be used later for the DRAWER.
Push the black lever up and
pull the SLIDE from the RAIL.
T
T
U
Use these holes.Open end
Open end
BLACK 1/2" PAN HEAD SCREW
(3 used in this step)
20
7

å Push twelve LARGE HIDDEN CAMS (1) into the
BACKS (E and H) and BRACE (F).
Step 3
F
E
H
Page 8 www.sauder.com/service 433360
Arrow
1
Arrow
1
1
1
Arrow

å Insert four LONG WOOD DOWELS (5) into the UPPER BACK (E).
å Push the LOWER BACK (H) onto the WOOD DOWELS in the
UPPER BACK (E).
Step 4
5
5
Surface with
HIDDEN CAMS
Surface with
HIDDEN CAMS
E
H
Notch
Page 9www.sauder.com/service433360

Step 5
å Insert three WOOD DOWELS (6) into the RIGHT END (A).
å Fasten the BACKS (E and H) and BRACE (F) to the RIGHT
END (A). Tighten five HIDDEN CAMS.
å NOTE: Be sure the WOOD DOWELS in the END insert
into the BACKS and BRACE.
å Insert two WOOD DOWELS (6) into the long edge of the
LOWER BACK (H).
E
F
H
Surface with
HIDDEN CAMS Surface with
HIDDEN CAMS
A
6
6
Surface with HIDDEN CAMS
Rounded edge
Notch
Page 10 www.sauder.com/service 433360
1