Sauder Portage Park 426281 User manual

sauder.com
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
sauder.com
CONTACT US FIRST
BEFORE MAKING ANY RETURNS TO THE STORE.
sauder.com
CONTACT US FIRST
BEFORE MAKING ANY RETURNS TO THE RETAILER.
Visit sauder.com/service to order replacement parts, view video assembly tips, or chat with a live rep.
Prefer the phone? Give us a ring at 1-800-445-1527.
Customer Service is available Monday-Friday - 9 a.m. to 5:30 p.m. EST (except holidays)
Sauder.com
Share your journey!
English pg 1-24
Français pg 25-28
Español pg 29-32
Lot # 560453 02/02/21
Purchased: __________________
Hutch
Portage Park Collection | Model 426281
Don't sweat the
small stu anymore.

Part Identification
Hardware Identification
Hardware Usage Guide
Assembly Steps
Français
Español
Safety
Warranty
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Table of Contents Assembly Tools Required
3
4
5
6-24
25-28
29-32
33-34
35
Electric drill with 1/8" or 3/8" bit
(ONLY in indicated step)
Pencil
Page 2 www.sauder.com/service 426281
Tape Measure

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
A TOP (1)
B BOTTOM (1)
C LEFT END (1)
D RIGHT END (1)
E LARGE UPRIGHT (1)
F SMALL UPRIGHT (1)
G BACK (1)
H SHELF (1)
J DOOR (1)
K FRAME (2)
L MOLDING (2)
A
B
C
D
E
G
H
J
K
L
L
K
F
Page 3www.sauder.com/service426281

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
HIDDEN CAM - 16
1CAM SCREW - 16 2WOOD DOWEL - 5 3DOOR ROLLER - 2 4
METAL PIN - 2
5 6 PULL - 1 APPLIQUE CARD - 4 78BUMPER CARD - 2
L-WRENCH - 1
9FURNITURE TIPPING
RESTRAINT KIT - 1
96
14 1/2" HEX HEAD SCREW - 8 9/16" FLAT HEAD SCREW - 4
15
1-9/16" HEX HEAD SCREW - 4
11
2" PAN HEAD SCREW - 4
10
1-9/16" PAN HEAD SCREW - 18
12 11/16" MACHINE SCREW - 2
13
Page 4 www.sauder.com/service 426281

Hardware Usage Guide
HOW TO USE A HIDDEN CAM & CAM SCREW OR CAM DOWEL
NOTE: Various CAM SCREWS or a CAM DOWEL may be used.
Cam Screws Cam Dowel
Turn the CAM SCREW or
gently tap the CAM DOWEL
until the shoulder is against
the surface of the part.
1.
Hidden Cam
Arrow
Push a HIDDEN CAM into
the part. The arrow in the
HIDDEN CAM must point
toward the hole in the
edge of the board.
Hole
2.
3.
1
2
Insert the CAM SCREW or CAM DOWEL into the
HIDDEN CAM. Tighten the HIDDEN CAM.
Page 5www.sauder.com/service426281

Step 1 Look for this icon. It means a video assembly tip is
available at www.sauder.com/service/tips
Find the numbered video or scan the QR code.
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å Push ten HIDDEN CAMS (1) into the RIGHT END (D),
UPRIGHTS (E and F), and SHELF (H).
å Turn six CAM SCREWS (2) into the RIGHT END (D),
UPRIGHT (E), and SHELF (H).
1
D
E
H
F
1
Arrow
Arrow
1
2
2
Page 6 www.sauder.com/service 426281
Some assembly
(and snacks) required.

å Fasten the RIGHT END (D) and UPRIGHTS (E and F) to
the SHELF (H). Tighten six HIDDEN CAMS.
Step 2 1
D
E
H
F
Surface with
HIDDEN CAMS
Surface without
HIDDEN CAMS
Surface without HIDDEN CAMS
Surface without
HIDDEN CAMS
Page 7www.sauder.com/service426281

å Turn ten CAM SCREWS (2) into the TOP (A).
Step 3 1
A
2
2
Page 8 www.sauder.com/service 426281

å Insert a WOOD DOWEL (3) into the TOP (A).
å Fasten the RIGHT END (D) and LARGE UPRIGHT (E) to
the TOP (A). Tighten four HIDDEN CAMS.
å NOTE: Be sure the WOOD DOWEL in the TOP inserts into
the RIGHT END.
Step 4
A
D
E
3
1
Page 9www.sauder.com/service426281

å Push two HIDDEN CAMS (1) into the LEFT END (C).
å Insert a WOOD DOWEL (3) into the TOP (A).
å Fasten the LEFT END (C) to the TOP (A). Tighten two
HIDDEN CAMS.
å NOTE: Be sure the WOOD DOWEL in the TOP inserts into
the LEFT END.
Step 5 1
A
C
C
Arrow
1
Surface with
HIDDEN CAMS
3
Page 10 www.sauder.com/service 426281

å Push four HIDDEN CAMS (1) into the BACK (G).
Step 6 1
G
Arrow
1
Page 11www.sauder.com/service426281

å Fasten the BACK (G) to the TOP (A).
Tighten four HIDDEN CAMS.
Step 7
G
A
Surface with
HIDDEN CAMS
1
Page 12 www.sauder.com/service 426281

å Fasten the DOOR ROLLERS (4) to the DOOR (J).
Use four 9/16" FLAT HEAD SCREWS (15).
Step 8
J
4
9/16" FLAT HEAD SCREW
(4 used in this step)
15
Page 13www.sauder.com/service426281

å Fasten the PULL (6) to the DOOR (J). Use two 11/16"
MACHINE SCREWS (13).
Step 9
J
6
11/16" MACHINE SCREW
(2 used in this step)
13
Page 14 www.sauder.com/service 426281
Now might be a
good time to refresh
your drink.

å Insert two METAL PINS (5) into the DOOR (J).
å Insert the METAL PINS (5) in one end of the DOOR (J) into the
groove in the TOP (A).
å Insert three WOOD DOWELS (3) into the BOTTOM (B).
å Fasten the BOTTOM (B) to the ENDS (C and D), UPRIGHTS (E and F),
and BACK (G). Use twelve 1-9/16" PAN HEAD SCREWS (12).
å NOTE: Be sure the WOOD DOWELS in the BOTTOM insert into the
ENDS and LARGE UPRIGHT.
Step 10
J
5
A
3
D
C
E
F
G
B
1-9/16" PAN HEAD SCREW
(12 used in this step)
12
12
Page 15www.sauder.com/service426281
(3 used)
Surface with more holes
This hole must be here.

å Fasten the FRAMES (K) to the MOLDINGS (L). Tighten eight
1/2" HEX HEAD SCREWS (14) using the L-WRENCH (9).
å NOTE: You should start each SCREW a few turns before
completely tightening any of them.
Step 11
Page 16 www.sauder.com/service 426281
K
L
L
K
9
14
1/2" HEX HEAD SCREW
(8 used in this step)
14

å Fasten the FRAMES (K) to the BOTTOM (B). Tighten four
1-9/16" HEX HEAD SCREWS (11) using the L-WRENCH (9).
å NOTE: You should start each SCREW a few turns before
completely tightening any of them.
Step 12
K
K
9
B
11
1-9/16" HEX HEAD SCREW
(4 used in this step)
11
Page 17www.sauder.com/service426281

å Fasten the MOLDINGS (L) to the BOTTOM (B).
Use six 1-9/16" PAN HEAD SCREWS (12).
Step 13
L
L
B
1-9/16" PAN HEAD SCREW
(6 used in this step)
12
Page 18 www.sauder.com/service 426281

å Carefully stand your unit upright.
å Peel the BUMPERS from the BUMPER CARD (8) onto the
edges of the DOOR (J) as shown.
å Peel APPLIQUES from the APPLIQUE CARDS (7) and
stick them onto each visible HIDDEN CAM.
Step 14
8
8
J
7
Page 19www.sauder.com/service426281
Pro Tip: Lift with your
legs. And, you know,
your arms.

å You have the option to fasten your Hutch to the 427478 Desk Top or the 427478 Return. To fasten your Hutch to the
Return, go to the next step now.
å First, place the hutch on the 427478 top using the measurements provided in the enlarged diagram. Then mark the
holes in the FRAMES (K) with your pencil.
å NOTE: Be sure to use the exact spacing for both ends of the FRAME (K) on the 427478 Top as shown in the
enlarged diagram.
å Next, remove the hutch from the 427478 Top. Then drill a 1/8" hole in the four marked locations of
your 427478 top.
å Now, fasten the FRAMES (K) to the 427478 large top. Use four 2" PAN HEAD SCREWS (10).
Step 15
427478
K
K
10
1-1/8"1-1/8"
5/8"5/8"
Page 20 www.sauder.com/service 426281
2" PAN HEAD SCREW
(4 used in this step)
10
Electric drill with 1/8" bit
Pencil