Sauder Camden 101730 User manual

NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
English pg 1-24
Français pg 25-28
Español pg 29-32
Lot # 364316 10/21/14
Purchased: __________________
Be sure to give us a ring before
making any returns. 1-800-523-3987
Computer Desk
Camden Collection | Model 101730
Need help? Visit Sauder.com to view video assembly tips or chat with a live rep.
Prefer the phone? Call 1-800-523-3987.
Share your journey!
sauder.com
Sit and surf.

Table of Contents Assembly Tools Required
2-3
4-5
6-24
25-28
29-32
33-34
35
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
101730 www.sauder.com/servicesPage 2
Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
A RIGHT END (1)
B LEFT END (1)
C RIGHT UPRIGHT (1)
D LEFT UPRIGHT (1)
E RIGHT SMALL UPRIGHT (1)
F LEFT SMALL UPRIGHT (1)
G TOP (1)
H BOTTOM (1)
I BACK (1)
J MODESTY PANEL (1)
K SHELF (1)
L MONITOR SHELF (1)
M KEYBOARD SHELF (1)
N BRACE (1)
O DRAWER FRONT (1)
T TOP MOLDING (1)
U RIGHT END MOLDING (1)
V LEFT END MOLDINIG (1)
W BASE (1)
X LEFT UPRIGHT MOLDING (1)
Y SMALL UPRIGHT MOLDING (2)
D14 RIGHT DRAWER SIDE (1)
D15 LEFT DRAWER SIDE (1)
D151 DRAWER BACK (1)
D953 DRAWER BOTTOM (1)

Part Identification
101730www.sauder.com/services Page 3
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
T
U
V
W
X
Y
Y
D14
D953
D15
D151

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
ANGLE BRACKET - 6
LL
METAL PIN - 1
QQ TOUCH-UP PEN - 1 RR
JJ TWIST-LOCK®
FASTENER - 18
CORD CLIP - 1
PP
ZZ SLIDE CAM - 2
35AW CABINET RIGHT - 1 35AY DRAWER RIGHT - 1 35AZ DRAWER LEFT - 1
35AX CABINET LEFT - 1
40CA CABINET RIGHT - 1 40CB CABINET LEFT - 1 40CC DRAWER RIGHT - 1 40CD DRAWER LEFT - 1
FILE ROD - 2
II RAIL BRACKET - 4
KK
HANDLE - 1
NN HANDLE MOUNT - 2 OO
101730 www.sauder.com/servicesPage 4
FILE GLIDE - 2
4B

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
101730www.sauder.com/services Page 5
BLACK 9/16" LARGE HEAD SCREW - 20
WW
SILVER 1-1/8" FLAT HEAD SCREW - 5
TT
VV SILVER 5/8" MACHINE SCREW - 2
BLACK 1-7/8" FLAT HEAD SCREW - 14
SS
UU BROWN 1" FLAT HEAD SCREW - 4
XX GOLD 5/16" FLAT HEAD SCREW - 12
NAIL - 23
YY 30S BLACK 1-9/16" FLAT HEAD SCREW - 4

Step 1 Look for this icon. It means a
video assembly tip is available at
www.sauder.com/services/tips
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å To begin assembly, push a SAUDER TWIST-LOCK®
FASTENER (JJ) into the large holes in the RIGHT END (A)
and LEFT END (B).
å Repeat this for the RIGHT UPRIGHT (C), RIGHT SMALL
UPRIGHT (E), LEFT SMALL UPRIGHT (F), BOTTOM (H),
MODESTY PANEL (J), and SHELF (K).
101730 www.sauder.com/servicesPage 6
(18 used)
JJ
Do not tighten the TWIST-LOCK® FASTENERS in this step.
A
B
Scan this QR code or go to this address:
http://qr.sauder.com/?ID=1729
to watch a video on how to assemble your unit.

å Fasten four RAIL BRACKETS (KK) to the RIGHT END (A)
and LEFT END (B). Use eight BLACK 9/16" LARGE
HEAD SCREWS (WW).
å Fasten the TOP MOLDING (T) to the TOP (G). Use five
SILVER 1-1/8" FLAT HEAD SCREWS (TT).
Step 2
101730www.sauder.com/services Page 7
KK
G
T
A
B
(4 used)
BLACK 9/16" LARGE HEAD SCREW
(8 used for the RAIL BRACKETS)
WW
Surface with
TWIST-LOCK®
FASTENERS
Surface with
TWIST-LOCK®
FASTENERS
SILVER 1-1/8" FLAT HEAD SCREW
(5 used in this step)
TT
Rounded edge
Remember:
Righty tighty.
Lefty loosey.

Step 3
å Place a short edge of the BASE (W) against the RIGHT END (A) so
the bottom edge is even with the bottom edge of the RIGHT END.
å Slide the RIGHT END MOLDING (U) onto the notched edge of the
RIGHT END (A) until it is against the BASE (W). Slide the LEFT END
MOLDING (V) onto the notched edge of the LEFT END (B), and
then slide the LEFT UPRIGHT MOLDING (X) onto the notched edge
of the LEFT UPRIGHT (D) as shown in the lower diagram.
å NOTE: The MOLDINGS should overhang the inside surfaces of the
ENDS and UPRIGHT. If the MOLDING overhangs the wrong surface,
remove it and slide it on again.
å Fasten an ANGLE BRACKET (LL) to the LEFT END (B). Use a BLACK
9/16" LARGE HEAD SCREW (WW).
å *U.S. Patent No. 5,499,886
101730 www.sauder.com/servicesPage 8
BLACK 9/16" LARGE HEAD SCREW
(1 used for the ANGLE BRACKET)
WW
LL
AW
B
U
V
D
X
These edges should be even.
These edges should be even.
Surface
with
more
holes
Surface with
TWIST-LOCK®
FASTENERS
Surface with
TWIST-LOCK®
FASTENERS
These edges must be even.
Slide the MOLDING (U)
against the BASE (W).
U

å Fasten the CABINET RIGHT (35AW) to the RIGHT UPRIGHT (C).
Fasten the CABINET RIGHT (40CA) to the RAIL BRACKETS (KK)
on the RIGHT END (A). Use a GOLD 5/16" FLAT HEAD SCREW (XX)
through the first and last holes in each RAIL.
å Fasten the CABINET LEFT (35AX) to the RAIL BRACKETS (KK) on
the LEFT END (B). Fasten the CABINET LEFT (40CB) to the other
surface of the RIGHT UPRIGHT (C). Use a GOLD 5/16" FLAT HEAD
SCREW (XX) through the first and last holes in each RAIL.
Step 4
101730www.sauder.com/services Page 9
Finished edge
Roller end
Roller end
Roller end
Roller end
A
B
C
Surface with
TWIST-LOCK®
FASTENERS
GOLD 5/16" FLAT HEAD SCREW
(8 used in this step)
XX

Step 5
å Fasten the RIGHT SMALL UPRIGHT (E) and LEFT SMALL
UPRIGHT (F) to the MONITOR SHELF (L). Tighten four
TWIST-LOCK® FASTENERS.
101730 www.sauder.com/servicesPage 10
L
F
E
Rounded edge
Notched edge
Surface with holes
Notched edge
Surface with
TWIST-LOCK®
FASTENERS
Surface without
TWIST-LOCK®
FASTENERS
How to use the SAUDER TWIST-LOCK®FASTENER
1. Insert the dowel end of the FASTENER into the hole of the
adjoining part.
NOTE: The dowel end of the FASTENER must remain fully
inserted in the hole of the adjoining part while locking
the FASTENER.
2. Tighten the FASTENER with a Phillips screwdriver as tight
as possible.
Dowel end