Sauder Nova Loft 423720 User manual

sauder.com
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
sauder.com
CONTACT US FIRST
BEFORE MAKING ANY RETURNS TO THE STORE.
Share your journey!
sauder.com
CONTACT US FIRST
BEFORE MAKING ANY RETURNS TO THE RETAILER.
Visit sauder.com/service to order replacement parts, view video assembly tips, or chat with a live rep.
Prefer the phone? Give us a ring at 1-800-445-1527.
Customer Service is available Monday-Friday - 9 a.m. to 5:30 p.m. EST (except holidays)
Sauder.com
L-Shaped Desk
Nova Loft Collection | Model 423720
English pg 1-26
Français pg 27-29
Español pg 30-32
Lot # 533399 11/11/19
Purchased: __________________
Business or pleasure. Works
both ways.

Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
Table of Contents Assembly Tools Required
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Skip the power trip.
This time.
3
4
5-26
27-29
30-32
33-34
35
Page 2 www.sauder.com/service 423720

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
A LEFT END (1)
B LEFT UPRIGHT (1)
C RIGHT UPRIGHT (1)
D RIGHT END (1)
E LEFT BACK (1)
F RIGHT BACK (1)
G LEFT SHELF (1)
H BACK (2)
K SMALL TOP (1)
L LARGE TOP (1)
M UPPER REAR MOLDING (2)
N UPPER FRONT MOLDING (2)
O LOWER FRONT MOLDING (2)
P LOWER REAR MOLDING (2)
Q BRACE (2)
R SMALL DRAWER FRONT (1)
S SMALL DRAWER BOX FRONT (1)
T SMALL DRAWER BACK (1)
UL SMALL LEFT DRAWER SIDE (1)
UR SMALL RIGHT DRAWER SIDE (1)
V DRAWER FRONT (1)
W DRAWER BOX FRONT (1)
X DRAWER BACK (1)
YL LEFT DRAWER SIDE (1)
YR RIGHT DRAWER SIDE (1)
Z FILE DRAWER FRONT (1)
AA FILE DRAWER BOX FRONT (1)
BB FILE DRAWER BACK (1)
CC FILE DRAWER SIDE (2)
DD DRAWER BOTTOM (2)
EE LARGE DRAWER BOTTOM (1)
FF RIGHT SHELF (1)
A
B
C
D
EF
G
H
H
K
L
N
N
O
O
Q
Q
R
S
TUR
UL
V
W
XYR
YL Z
AA
BBCC
CC
DD
DD
EE
FF
P
P
M
M
Page 3www.sauder.com/service423720

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
BLACK 5/8" FLAT HEAD SCREW - 13
15
BLACK 7/8" HEX HEAD SCREW - 8
13
BLACK 1-3/4" FLAT HEAD SCREW - 4
11 BLACK 1-9/16" FLAT HEAD SCREW - 24
12
L-WRENCH - 1
8
PULL - 3
7
FILE GLIDE - 2
9FILE HANGER - 2 10
(EXTENSION SET SHOWN SEPARATED)
EXTENSION SLIDE - 2
2
EXTENSION RAIL - 2
1
LEFT DRAWER
SLIDE - 2
6
RIGHT DRAWER
SLIDE - 2
5
LEFT CABINET
RAIL - 2
4
RIGHT CABINET
RAIL - 2
3
BLACK 13/16" MACHINE SCREW - 6
14
BLACK 1/2" FLAT HEAD SCREW - 36
16
Page 4 www.sauder.com/service 423720
BLACK 3/8" MACHINE SCREW - 34
17

Step 1 Look for this icon. It means a
video assembly tip is available at
www.sauder.com/service/tips
å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor.
å Separate the EXTENSION SLIDES (2) from the EXTENSION RAILS (1) as shown in the upper diagram below. Be
prepared, the parts are greasy.
å Fasten the EXTENSION RAILS (1) to the RIGHT UPRIGHT (C) and RIGHT END (D). Use six BLACK 1/2" FLAT HEAD
SCREWS (16).
å NOTE: For each EXTENSION RAIL, turn three screws into the holes shown in the upper diagram. Slide the inner
cartridge of the EXTENSION RAIL in to find the other holes that lines up with the hole in the END. Turn a SCREW into
these holes.
å NOTE: The EXTENSION SLIDES will be used later for the DRAWERS.
C
D
21
1
1
Open end
Open end
Push the black lever up and pull the SLIDE from the RAIL.
BLACK 1/2" FLAT HEAD SCREW
(6 used in this step)
16
Page 5www.sauder.com/service423720
Slide the inner
cartridge to find
these holes.
Slide the inner
cartridge to find
these holes.
Surface with holes Surface with holes
This hole
must be
closer to
this edge.
This hole
must be
closer to
this edge.

Page 6 www.sauder.com/service 423720
å Fasten an UPPER REAR MOLDING (M) to the RIGHT BACK (H).
Use two BLACK 5/8" FLAT HEAD SCREWS (15).
å Fasten a LOWER REAR MOLDING (P) to the RIGHT
BACK (H). Use two BLACK 1-3/4"FLAT HEAD SCREWS (11).
Step 2
H
M
P
BLACK 1-3/4" FLAT HEAD SCREW
(2 used in this step)
11
BLACK 5/8" FLAT HEAD SCREW
(2 used in this step)
15
These holes must be here.

Page 7www.sauder.com/service423720
å Fasten one of each FRONT MOLDINGS (N and O) to the
RIGHT UPRIGHT (C). Use two BLACK 3/8" MACHINE
SCREWS (17).
å Fasten the REAR MOLDINGS (M and P) to the RIGHT
UPRIGHT (C). Use two BLACK 3/8" MACHINE SCREWS (17).
Step 3
H
M
P
N
O
C
The tab
should be
closer to
this edge.
17
BLACK 3/8" MACHINE SCREW
(4 used in this step)
Some assembly
(and snacks) required.

Page 8 www.sauder.com/service 423720
å Fasten the RIGHT END (D) to the FRONT MOLDINGS (N
and O) and REAR MOLDINGS (P and M). Use four BLACK
3/8" MACHINE SCREWS (17).
Step 4
N
O
D
P
17
BLACK 3/8" MACHINE SCREW
(4 used in this step)

Page 9www.sauder.com/service423720
å Fasten the RIGHT SHELF (FF) to the UPPER MOLDINGS (M
and N). Use four BLACK 5/8" FLAT HEAD SCREWS (15).
Step 5
N
FF
BLACK 5/8" FLAT HEAD SCREW
(4 used in this step)
15

Page 10 www.sauder.com/service 423720
å Carefully stand your unit upright.
å NOTE: You will need a short screwdriver in this step.
å Fasten a BRACE (Q) to the RIGHT UPRIGHT (C). Use a
BLACK 3/8" MACHINE SCREW (17).
å Fasten the RIGHT BACK (F) to the BRACE (Q). Use a
BLACK 3/8" MACHINE SCREW (17).
å Fasten the LEFT BACK (E) to the RIGHT BACK (F). Use a
BLACK 3/8" MACHINE SCREW (17) and a BLACK 5/8"
FLAT HEAD SCREW (15).
Step 6
BLACK 5/8" FLAT HEAD SCREW
(1 used in this step)
15
17
BLACK 3/8" MACHINE SCREW
(3 used in this step)
C
E
FQ