Sauder project 62 User manual

>> assembly instructions
project 62
entertainment credenza
style # 423337 (pale oak)
dpci # 249 - 10 - 1970

2 423337
Use of a TV that is too heavy or large is hazardous. A TV that is too heavy will create a risk of a tip-over that can cause severe injury or death.
A TV that is too large for the available space might be accidentally pushed or bumped off the furniture, or subject to tip-over.
• Check the size and weight of your TV. Compare it to the diagram below – before you begin assembly!
• This Sauder unit is designed for use with televisions weighing less than 80 pounds. Never use with a TV that weighs more.
• The size of the television, front-to-back and side-to-side, must fit within the space defined in the diagram.
• Never place the front edge of the TV past the front edge of the TV support shelf (or stop molding – if equipped)
• Never allow the sides of the TV to extend past the side edges of the TV support surface.
• If the TV has a CRT picture tube, the picture tube cone may extend past the rear of the support shelf.
• Be sure to apply the warning label as instructed in the last assembly step. The label provides important safety related information.
WARNING
19-1/2"
55"
80 lbs.

3 423337
Congratulations on your latest Target purchase.
Now what? Don’t start sweating over this box of parts. This will be easy. We did the hard work for you.
All you need to do is follow our simple instructions and you’ll be on your way to transforming your room in no time.
Good luck—though we’re confident you won’t need it.
tools needed
before you begin
1. Check for damaged or missing parts. Visit www.sauder.com/services to order missing supplies.
2. Use the carton as a working surface to prevent product damage during assembly.
3. Gather all tools prior to assembly.
tip shown
actual size

4 423337
table of contents
tv warning 2
introduction 3
parts list 5
hardware 6
assembly 7-21
warranty 22
important safety information 23
a note from the manufacturer:
register your product online.
www.sauder.com
For immediate service, our website is available 24 hours a day,
7 days a week to order replacement parts, access assembly tips,
register your product, and view Sauder products.
Monday – Friday 9am – 5:30pm ET
United States and Canada (except holidays)
Consumer Services 1-800-523-3987
Most replacement parts ship from our facility in one or two business days.
Please contact Sauder customer service before returning your product to
the store. Most questions, concerns, or parts needs can be addressed
by Sauder customer service assistance at www.sauder.com/services.
NOTE: This instruction booklet contains important safety information.
Please read and keep for future reference.
Record the date you purchased this unit and save the booklet for future
reference. If you ever need to contact Sauder about this unit, refer to
the lot # and the style # when calling our toll-free number.
For more information about our furniture, company, or to order
replacement parts, please visit our web site.
Lot #: 514620
Date Purchased:______________ 03 / 22 / 18

5 423337
part list
ITEM DESCRIPTION QUANTITY
A right end 1
B left end 1
C top 1
D bottom 1
E upright 2
F center adjustable shelf 1
G adjustable shelf 2
H front skirt 1
J left skirt 1
K back skirt 1
L back 1
M right door 1
N left door 1
O louver 10
P right skirt 1
While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other.
Use this part list to help identify similar parts.
A
B
C
D
E
M
G
H
J
L
F
G
KO
E
O
O
O
O
N
O
O
O
O
O
P

6 423337
hardware
Using a screw that is too long will cause damage. Before beginning assembly, separate each type of screw. Carefully study the screw
diagrams (SHOWN ACTUAL SIZE). Pay close attention to the color of each screw. You may receive extra hardware with your unit.
(60H) x 4
hinge
(11F) x 8
twist-lock®fastener
(31G) x 4
corner bracket
(1R) x 16
metal pin
(2R) x 12
rubber sleeve
(1S) x 36
black 9/16" large head screw
(11S) x 2
black 1/2" flat head screw
(12S) x 20
brown 1" flat head screw
(51S) x 4
black 9/16" pan head screw
(6L) x 1
warning label
WARNING
Never use this furniture with a TV that is
too large or too heavy. Severe injury or
death can occur. The TV and furniture
will be unstable and may tip.
-The TV must less than 80 lbs.
-The base of the TV must be able to sit
completely on this shelf.
Refer to instruction book for complete
safety information.
Note: This is a permanent label. Do not
try to remove. Surface will be damaged.
02/10 331663
(Refer to the last step for proper
location and application)
(113S) x 8
black 1-15/16" flat head screw
(4G) x 6
metal bracket
(12I) x 2
magnetic catch
(6I) x 2
strike plate

7 423337
Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor.
To begin assembly, push a SAUDER TWIST-LOCK®FASTENER (11F) into the large holes in the ENDS (A and B) and UPRIGHTS (E).
NOTE: Do not tighten the TWIST-LOCK®FASTENERS at this time.
step 1.
Look for this icon. It means a
video assembly tip is available at
www.sauder.com/services/tips
11F
(11F) x 8
twist-lock®fastener
A
B
E
E

8 423337
step 2.
Fasten the MAGNETIC CATCHES (12I) to the TOP (C). Use four BLACK 9/16" PAN HEAD SCREWS (51S).
NOTE: Position the MAGNETIC CATCHES exactly as shown.
(51S) x 4
black 9/16" pan head screw
C
12I
Surface with holes
(12I) x 2
magnetic catch

9 423337
step 3.
Fasten the RIGHT END (A) to the TOP (C). Tighten two TWIST-LOCK®FASTENERS.
A
C
Surface with
TWIST-LOCK®
FASTENERS
These holes
must be here.
The MAGNETIC
CATCHES will be
closer to this edge.
These edges
should be even.
How to use the SAUDER TWIST-LOCK®FASTENER
1. Insert the dowel end of the FASTENER into the
hole of the adjoining part.
NOTE: The dowel end of the FASTENER must
remain fully inserted in the hole of the adjoining part
while locking the FASTENER.
2. Tighten the FASTENER with a Phillips screwdriver
as tight as possible.
Dowel end

10 423337
Insert two METAL PINS (1R) into the RIGHT END (A). Place the BACK (L) onto the METAL PINS in the RIGHT END.
step 4.
(1R) x 2
metal pin
A tracking label will
be on this surface.
Please do not remove.
A
L
These edges
should be even.
Finished
edge