Sauder 411371 User manual

sauder.com
Bookcase
Model 411371
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
English pg 1-16
Français pg 17-18
Español pg 19-20
Lot # 532579 08/14/19
Purchased: __________________
sauder.com
CONTACT US FIRST
BEFORE MAKING ANY RETURNS TO THE STORE.
Share your journey!
sauder.com
CONTACT US FIRST
BEFORE MAKING ANY RETURNS TO THE STORE.
Visit sauder.com/service to order replacement parts, view video assembly tips, or chat with a live rep.
Prefer the phone? Give us a ring at 1-800-523-3987.
Customer Service is available Monday-Friday - 9 a.m. to 5:30 p.m. EST (except holidays)
Here's one for
the books.

Table of Contents Assembly Tools Required
3
4
5-16
17-18
19-20
21-22
23
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Skip the power trip.
This time.
411371 www.sauder.com/servicePage 2

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
A RIGHT END (1)
B LEFT END (1)
C BACK (1)
E TOP (1)
F BOTTOM (1)
H SHELF MOLDING (2)
I END MOLDING (2)
J AJUSTABLE SHELF (2)
M22 TOP MOLDING (1)
M23 BASE (1)
Now you know
our ABCs.
411371www.sauder.com/service Page 3
A
B
C
M23
E
F
M22
H
I
J
I
H
J

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
411371 www.sauder.com/servicePage 4
SAFETY BRACKET - 1
1G
ANGLE BRACKET - 14
5G
RUBBER SLEEVE - 8
2R
CAM COVER - 4
12P
METAL PIN - 8
1R
HIDDEN CAM - 8
1F CAM DOWEL - 8 2F
BLACK 9/16" LARGE HEAD SCREW - 29
1S BLACK 1-7/8" FLAT HEAD SCREW - 1 2S
NAIL - 28
1N

Step 1 Look for this icon. It means a
video assembly tip is available at
www.sauder.com/service/tips
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å Push eight HIDDEN CAMS (1F) into the ENDS (A and B)
and BOTTOM (F). Then insert the metal end of a CAM
DOWEL (2F) into each HIDDEN CAM.
411371www.sauder.com/service Page 5
A
B
F
Arrow
1F
2F
(8 used)
Arrow
1F
2F Do not tighten the HIDDEN CAMS in this step.
Insert the metal end of the CAM
DOWEL into the HIDDEN CAM.
Arrow

Step 2
å Fasten fourteen ANGLE BRACKETS (5G) to the ENDS (A and
B), BOTTOM (F), and TOP MOLDING (M22). Use fourteen
BLACK 9/16" LARGE HEAD SCREWS (1S).
å NOTE: Be sure the edges of the ANGLE BRACKETS are even
with the edges of the ENDS, BOTTOM, and TOP MOLDING.
411371 www.sauder.com/servicePage 6
A
B
F
5G
5G
M22
(14 used)
BLACK 9/16" LARGE HEAD SCREW
(14 used in this step)
1S
Remember:
Righty tighty.
Lefty loosey.

å Fasten the ENDS (A and B) to the BOTTOM (F). Tighten
four HIDDEN CAMS.
Step 3
411371www.sauder.com/service Page 7
A
B
F
Unfinished edge
Unfinished edge
Finished edge
Surface with
HIDDEN CAMS
Surface without
HIDDEN CAMS
Surface with
HIDDEN CAMS
Start Tighten
Arrow
Minimum
190 degrees
Caution
Risk of damage or
injury. HIDDEN CAMS
must be completely
tightened. HIDDEN
CAMS that are not
completely tightened
may loosen, and parts
may separate. To
completely tighten:
Arrow
Maximum
210 degrees
Do not stand the unit upright without the
BACK fastened. The unit may collapse.
Caution

Step 4
å Fasten the TOP (E) to the ENDS (A and B). Tighten four
HIDDEN CAMS.
411371 www.sauder.com/servicePage 8
A
B
E
Arrow
Minimum
190 degrees
Maximum
210 degrees
Rounded edge
Surface with holes

å Fasten the TOP MOLDING (M22) to the TOP (E). Use
three BLACK 9/16" LARGE HEAD SCREWS (1S).
å NOTE: Do not overtighten the SCREWS into the TOP.
Step 5
411371www.sauder.com/service Page 9
E
M22
BLACK 9/16" LARGE HEAD SCREW
(3 used in this step)
S
Curved edge

Step 6
å Carefully turn your unit over onto its front edges.
å Fasten the END MOLDINGS (I) to the ENDS (A and B).
Use six BLACK 9/16" LARGE HEAD SCREWS (1S).
å NOTE: There are no pre-drilled holes in the END
MOLDINGS. The SCREWS will tighten into the grooves.
411371 www.sauder.com/servicePage 10
A
B
I
I
The END MOLDINGS (I)
should be against the
TOP MOLDING (M22).
M22
BLACK 9/16" LARGE HEAD SCREW
(6 used in this step)
1S
Groove to inside
Groove to inside
Just think. The sooner
you do this, the sooner
you do something else.