Sauder Lateral File 419606 User manual

Need help? Visit Sauder.com to view video assembly tips or chat with a live rep.
Prefer the phone? Call 1-800-523-3987.
Share your journey!
sauder.com
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
Enlish p 1-24
Français p 25-28
Español p 29-32
Lot # 376736 11/03/15
Purchased: __________________
Be sure to ive us a rin before
makin any returns. 1-800-523-3987
Lateral File
Via Collection | 419606
Get all organized
and stu.

Table of Contents Assembly Tools Required
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Skip the power trip.
This time.
3
4-5
6-24
25-28
29-32
33-34
35
419606 www.sauder.com/servicesPae 2

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the ede
to help distinuish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
A RIGHT END (1)
B LEFT END (1)
C TOP (1)
D BOTTOM (1)
E SHELF (1)
F BACK (1)
G BASE (1)
H DRAWER FRONT (2)
B35 DRAWER BOTTOM (2)
D205 LEFT DRAWER SIDE (2)
D498 RIGHT DRAWER SIDE (2)
D499 DRAWER BACK (2)
M63 DRAWER BRACE (2)
419606www.sauder.com/services Pae 3
A
B
C
D
E
F
G
H
B35
D205
D498
D499
M63

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
419606 www.sauder.com/servicesPae 4
34G INTERLOCK
MECHANISM - 1
DRAWER
ACTUATOR - 2
62G
FILE BAR - 4
1B
PROPEL NUT - 4
14M
METAL BRACKET - 5
4G
17E LEVELER BRACKET - 4
GROMMET CAP - 1
1P
7F TWIST-LOCK®FASTENER - 18
16E ADJUSTABLE
GLIDE - 4
PULL - 2
12K
CAM SCREW - 2
8F
CORD CLIP - 2
9P
LOCK
BRACKET - 2
5J LOCK
COVER - 2
10J
FILE BRACKET - 4
12B
HIDDEN CAM - 2
1F
LOCK - 2
16J
(EXTENSION SET SHOWN SEPARATED)
IEXTENSION RAIL - 4 JEXTENSION SLIDE - 4
FILE ROD - 4
18B FILE GLIDE - 4 19B

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
419606www.sauder.com/services Pae 5
64P HALF GROMMET
CAP - 2
BLACK 9/16" PAN HEAD SCREW - 11
51S
BLACK 9/16" LARGE HEAD SCREW - 12
1S
SUPPORT PIN - 4
5R
BROWN 7/16" LARGE HEAD SCREW - 16
6S
BLACK 7/8" MACHINE SCREW - 4
37S
BLACK 1/2" FLAT HEAD SCREW - 10
11S
GROMMET - 1
10P
30S BLACK 1-9/16" FLAT HEAD SCREW - 10
HALF GROMMET - 2
67P

Step 1 Look for this icon. It means a
video assembly tip is available at
www.sauder.com/services/tips
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratchin your unit or the floor.
å To bein assembly, push a SAUDER TWIST-LOCK®
FASTENER (7F) into the lare holes in the BACK (F).
Repeat this step for the ENDS (A and B), BOTTOM (D),
and SHELF (E).
419606 www.sauder.com/servicesPae 6
Do not tihten the TWIST-LOCK® FASTENERS in this step.
(18 used)
7F 7F
7F
F
Some assembly
(and snacks) required.
STOP
If you purchased
the 419708 Hutch,
assemble it first.

Step
419606www.sauder.com/services Pae 7
Step 2
8F
å Turn two CAM SCREWS (8F) into the DRAWER FRONTS (H).
å Push two HIDDEN CAMS (1F) into the DRAWER BRACES (M63).
Arrow
The arrow in the HIDDEN
CAM must point toward the
hole in the ede of the board.
Hole
M63
M63
Arrow
1F
H
H

StepStep 3
419606 www.sauder.com/servicesPae 8
å Separate the EXTENSION SLIDES (J) from the EXTENSION RAILS (I) as shown in the upper diaram below. Be prepared,
the parts are reasy.
å Fasten the EXTENSION RAILS (I) to the ENDS (A and B). Use eiht BLACK 9/16" PAN HEAD SCREWS (51S).
å NOTE: For each EXTENSION RAIL, turn a SCREW into the hole shown in the enlared diaram. Then, slide the inner
cartride of the EXTENSION RAIL in to find the other hole that lines up with the hole in the END. Turn a SCREW into this
hole. You may need to apply some pressure on the SCREW with your Screwdriver to et it into the hole.
Push the black lever up and pull the SLIDE from the RAIL.
IJ
A
B
Surface with
TWIST-LOCK®
FASTENERS
Surface with
TWIST-LOCK®
FASTENERS
Open end
Open end
Use this hole.
NOTE: Be sure to use the
correct screw in this step.
BLACK 9/16" PAN HEAD SCREW
(8 used in this step)
51S
I
I
I
I
This small hole
must be here.
This small hole
must be here.

Step
419606www.sauder.com/services Pae 9
Step 4
A
B
D
å Fasten the INTERLOCK MECHANISM (34G) to the RIGHT
END (A). Use three BLACK 9/16" PAN HEAD SCREWS (51S).
å With your hammer, ently tap four SUPPORT PINS (5R)
into the ENDS (A and B).
å Fasten five METAL BRACKETS (4G) to the ENDS (A
and B) and BOTTOM (D). Use five BLACK 9/16" LARGE
HEAD SCREWS (1S).
å NOTE: Be sure the BRACKETS are even with the edes of
the ENDS and BOTTOM. 34G
BLACK 9/16" PAN HEAD SCREW
(3 used in this step)
51S
4G
BLACK 9/16" LARGE HEAD SCREW
(5 used for the METAL BRACKETS)
1S
5R
4G
4G

StepStep 5
419606 www.sauder.com/servicesPae 10
å Place a LEVELER BRACKET (17E) over the holes in the bottom
edes of the ENDS (A and B).
å Use a hammer to drive a PROPEL NUT (14M) throuh each
BRACKET and into the holes in the ENDS. Now, turn an
ADJUSTABLE GLIDE (16E) into each PROPEL NUT.
å NOTE: To raise a corner of the unit, turn the ADJUSTABLE
GLIDE counter-clockwise. To lower a corner, turn the
ADJUSTABLE GLIDE clockwise.
A
B
17E
16E
14M