Sauder 414720 User manual

PLEASE CONTACT US
BEFORE RETURNING
YOUR UNIT TO THE STORE
1-800-523-3987
www.sauder.com
Made in the USA
Archbold, OH
NOTE: THIS INSTRUCTION BOOKLET CONTAINS
IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
English.................... Page 1-22
Français...............Pages 23-25
Espanol.............Páginas 26-28
Lot #: 350556 04 / 22 / 13
Date Purchased: ____________________
414720
Highboy TV Stand
Barrister Lane Collection

ASSEMBLY TOOLS REQUIRED
Hammer
No. 2 Phillips Screwdriver
Tip Shown Actual Size
ADULT ASSEMBLY REQUIRED
TABLE OF CONTENTS
Part Identification.......................3
Hardware Identification .............4
Assembly Steps....................5-22
Français..............................23-25
Espanol...............................26-28
Safety .................................29-30
Warranty...................................31
Use of a TV that is too heavy or large is hazardous. A TV that is too heavy will create a risk of a tip-over that can cause severe injury
or death. ATV that is too large for the available space might be accidentally pushed or bumped off the furniture, or subject to tip-over.
• Check the size and weight of your TV. Compare it to the diagram below – before you begin assembly!
• This Sauder unit is designed for use with televisions weighing less than 50 pounds. Never use with a TV that weighs more.
• The size of the television, front-to-back and side-to-side, must fit within the space defined in the diagram.
• Never place the front edge of the TV past the front edge of the TV support shelf (or stop molding – if equipped)
• Never allow the sides of the TV to extend past the side edges of the TV support surface.
• If the TV has a CRT picture tube, the picture tube cone may extend past the rear of the support shelf.
• Be sure to apply the warning label as instructed in the last assembly step. The label provides important safety related information.
WARNING
18-3/4" 41-5/8"
50 lbs.
Page 2 www.sauder.com/services 414720

PART IDENTIFICATION: While not all parts are labeled, some of the parts will have a label or an inked
letter on the edge to help distinguish similar parts from each other. Use this PART IDENTIFICATION to help
identify similar parts.
A RIGHT END 1
B LEFT END 1
C LOWER RIGHT END 1
D LOWER LEFT END 1
E UPRIGHT 1
F LOWER UPRIGHT 1
G TOP 1
H BOTTOM 1
I SHELF 1
J BACK 1
K BRACE 1
L DOOR 4
M FRONT MOLDING 1
N RIGHT MOLDING 1
O LEFT MOLDING 1
P FRONT BASE 1
Q SIDE BASE 2
R SIDE RAIL 2
S BACK RAIL 1
Page 3
www.sauder.com/services414720
A
B
C
D
E
F
G
H
I
J
K
LL
LL
MN
O
P
Q
Q
R
RS

HARDWARE IDENTIFICATION
Screws are shown actual size. You may receive extra hardware with your unit.
Page 4 www.sauder.com/services 414720
WARNING
Never use this furniture with a TV that is
too large or too heavy. Severe injury or
death can occur.The TV and furniture
will be unstable and may tip.
-The TV must less than 50 lbs.
-The base of the TV must be able to sit
completely on this shelf.
Refer to instruction book for complete
safety information.
Note: This is a permanent label. Do not
try to remove. Surface will be damaged.
08/05 2 6 9 2 2 0 269220
WARNING LABEL - 1
1L
(Refer to the last step for proper location and application)
PULL- 4
70K
SAFETY STOP - 1
36M
DOOR SLIDE - 8
37M
DOOR HANGER- 8
40G
BROWN 7/16" LARGE HEAD SCREW - 16
6S
RUBBER SLEEVE - 8
2R
BLACK 1-7/8" FLAT HEAD SCREW - 15
2S
MOLDING CONNECTOR - 2
19F
NAIL - 46
1N METAL PIN - 8 1R
SILVER 1-1/8" FLAT HEAD SCREW - 7
10S
CAM SCREW - 4
8F
HIDDEN CAM - 16
1F CAM DOWEL - 12 2F ANGLE BRACKET - 8 5G
BLACK 9/16" LARGE HEAD SCREW - 24
1S
DOOR STOP - 4
4I
GOLD 1" MACHINE SCREW - 8
50S
BROWN 1" FLAT HEAD SCREW - 4
12S SILVER 5/8" MACHINE SCREW - 2 15S

Look for this icon. It means a video
assembly tip is available at:
www.sauder.com/services/tips
1
1
S
t
e
p
Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor.
Push sixteen HIDDEN CAMS (1F) into the ENDS (A and B), LOWER ENDS (C and D), UPRIGHTS (E and F), and BOTTOM (H).
Then, insert the metal end of a CAM DOWEL (2F) into each HIDDEN CAM, except in the ENDS (A and B).
Page 5
www.sauder.com/services414720
Do not tighten the HIDDEN CAMS in this step.
Do not insert
CAM DOWELS
into these edges.
Arrow
(12 used)
(16 used)
Arrow
1F
2F
2F Insert the metal end of the CAM
DOWEL into the HIDDEN CAM.
Arrow
1F
A
B
E
C
D
F
H

Fasten eight DOOR SLIDES (37M) to the ENDS (A and B), LOWER ENDS (C and D), and UPRIGHTS (E and F). Use twelve
BROWN 7/16" LARGE HEAD SCREWS (6S).
2
2
S
t
e
p
Page 6 www.sauder.com/services 414720
A
B
E
C
D
F
Finished edge
Finished edge
Finished edge
Finished edge
The large hole will be
closest to the finished
edge of all parts.
Do not fasten this end of the
DOOR SLIDE until step 17.
Do not fasten this end of the
DOOR SLIDE until step 17.
BROWN 7/16" LARGE HEAD SCREW
(12 used in this step)
6S
37M
37M
37M
37M
37M
37M
37M
37M
37M
37M

Fasten the RAILS (R and S) to the TOP (G). Use seven BLACK 1-7/8" FLAT HEAD SCREWS (2S).
3
3
S
t
e
p
Page 7
www.sauder.com/services414720
BLACK 1-7/8" FLAT HEAD SCREW
(7 used in this step)
2S
GR
R
S
Rounded edge
Rounded edge
Finished surface
Surface with
more holes

4
4
S
t
e
p
Page 8 www.sauder.com/services 414720
Tap two MOLDING CONNECTORS (19F) into the notches in the MOLDINGS (M, N and O).
Flat end
Flat end
Use your hammer to tap the MOLDING CONNECTOR (19F) into the notches in the MOLDINGS.
MN
O19F
19F

Fasten the MOLDINGS (M, N and O) to the TOP (G). Use seven SILVER 1-1/8" FLAT HEAD SCREWS (10S).
5
5
S
t
e
p
Page 9
www.sauder.com/services414720
M
N
O
G
SILVER 1-1/8" FLAT HEAD SCREW
(7 used in this step)
10S
Finished surface

6
6
S
t
e
p
Page 10 www.sauder.com/services 414720
Turn four CAM SCREWS (8F) into the MOLDINGS (N and O).
8F
N
O