Savant SmartControl 3 User manual

SSC-W003I Quick Reference Guide | 009-1504-02 45 Perseverance Way, Hyannis, MA 02601
Copyright © 2021 Savant Systems, Inc. | 211207 1 of 2 Savant.com | 508.683.2500
Box Contents
(1) SmartControl 3 Controller (SSC-W003I)
(1) Installation Kit (075-0174-xx)
(1) Mounting Plate (074-0569-xx)
(1) 6-pin Screw Down Plug-in Connector (028-9352-xx)
(1) 5V DC 1.2A Power Supply (025-0207-xx)
(1) Cable Tie (014-0071-xx)
(1) Product Regulatory Insert (009-1950-xx)
Specifications
Environmental
Temperature 32° to 104° F (0° to 40°C)
Humidity 10% to 90% (non-condensing)
Dimensions and Weights
Height Width Depth Weight
Device 0.64 in
(1.62 cm)
2.70 in
(6.85 cm)
2.67 in
(6.78 cm)
0.50 lbs
(0.22 kg)
Shipping 3.00 in
(7.62 cm)
7.00 in
(17.78 cm)
10.00 in
(25.40 cm)
2.00 lbs
(0.90 kg)
Power
Input 5V DC 1.2A
Maximum 6 watts
Standards
Wireless
Wi-Fi (802.11 b/g/n 2.4 GHz)
IMPORTANT! 802.11r (fast roaming) is not
supported.
Security WPA™, WPA2™, WPA/WPA2™, WEP
Savant® SmartControl 3 Wi-Fi Controller (SSC-W003I)
Quick Reference Guide
Network Guidelines
For more information, see the Savant Device Networking Guidelines
on the Savant Customer Community.
Front Panel
A
Press and hold for five seconds while powered On to clear the
network settings. The Status LED blinks rapidly when reset is
complete.
B
O: No Power
On Solid: Provisioned to the local network and communicating
with the Savant System Host.
Blinks Once: In Provisioning Mode. Ready to be added to the
local network.
1s.5s
REPEAT
Blinks Twice: Establishing connection with the local network.
.5s.5s .5s
REPEAT
1s
Blinks Three Times: Connected to the local network and is
connecting to the Host.
.5s .5s.5s .5s
REPEAT
.5s 1s
Short O Blink: Firmware is updating.
.5s1.5s
REPEAT
Rapid Blink: The reset button was held down for at least five
seconds and the SSC-W003I is performing a factory reset. After
reset, all network settings are cleared and the factory defaults
are set.
.1s.1s .1s
REPEAT
.1s
Reset
Status
B
A
Regulatory
Safety and
Emissions
FCC Part 15 CE C-Tick UKCA
Contains FCC ID: TLZ-CU277B
Contains IC: 6100A-CU277B
RoHS Compliant
Minimum Supported Releases
Savant OS da Vinci 8.4

SSC-W003I Quick Reference Guide | 009-1504-02 45 Perseverance Way, Hyannis, MA 02601
Copyright © 2021 Savant Systems, Inc. | 211207 2 of 2 Savant.com | 508.683.2500
Rear Panel
C
AB
5 VDC
-IR
1 2 3-
+ - + - +
A
IR
Used to send IR signals to control devices with
an IR input or IR receiver via an IR flasher (5V
tolerant only).
Before making connections, see the IR Wiring
section for important precautions regarding IR
functionality.
B
Input Power 5V DC 1.2A - Connect to included power supply.
C
Cable Lance Use with included cable tie to secure power
supply connection.
IR Wiring
IR connections are made using the 6-pin screw down plug-in type
connector included with each SSC-W003I controller. This connector
plugs into the connection on the rear of the controller.
IMPORTANT! IR Wiring Precuations
–Ensure all IR emitters are within 15 feet (4.6 meters) from the
controller’s location.
–Use of 3rd party flashing IR emitters with Talk Back is not
recommended. These types of emitters can draw voltage away
from the IR signal that can degrade IR performance.
Making Connections
1. Remove from power if power is applied.
2. Pull to remove the terminal block from the rear of the controller.
3. With a small flat bladed screwdriver,
turn the screws on the top of
connector counterclockwise until
the silver crimps in the front of the
connector opens enough to slide the
wire(s) into the square slots.
4. Strip back the insulation on each of
the wires ¼ inch. Insert the stripped
wires into their proper ports. Do not
allow more than ⅛ inch of bare wire
exposed.
5. Turn the screws clockwise until the screw tightens around the wire.
Tug on the wire a bit to verify the wires are installed securely.
6. Continue until all wires are installed.
7. Repeat steps 3 - 5 for any additional IR devices.
8. Plug terminal block back into the rear of the controller.
9. Reapply power.
Connecting to a Wireless Network
To provision the SSC-W003I controller onto a local network, one of the
following methods can be used:
–SmartConnect Application – da Vinci 8.4 or later.
–Embedded Web UI – All da Vinci builds.
Both methods are described in the SmartControl 3 Wi-Fi Controller
[SSC-W003I-01] Deployment Guide.
Additional Documentation
Additional Documentation is available on the Savant Customer
Community.
–SmartControl 3 Wi-Fi Controller [SSC-W003I-01] Deployment
Guide (009-1518-xx)
–SmartConnect Software [SCA-CONF, SCA-CONFL] Reference Guide
(009-1046-xx)
–SmartControl 3 SSC-W003I Troubleshooting Guide.
4 5 632
1
PIN 1 IR 1-
PIN 2 IR 1+
PIN 3 IR 2-
PIN 4 IR 2+
PIN 5 IR 3-
PIN
Use White Stripe
for Positive (+)
6 IR 3+
-
+- +
-+
1 2 3
< 1/8 inch
bare wire
exposed