Savant SmartControl RS232 User manual

Savant® SmartControl RS232 – Wi-Fi Smart Controller with 2 RS232
Quick Reference Guide
For Product Info
SSC-W02R-00 |009-1373-03 | 161104!
!
!
!
45 Perseverance Way, Hyannis, MA 02601!
Copyright © 2016 Savant Systems, LLC
1
of
2!
Savant.com | 508.683.2500
Box Contents
(1) SmartControl RS232 (SSC-W02R-00)
(1) Installation Kit (075-0174-xx)
(1) Mounting Plate (074-0569-xx)
(1) 6-pin Screw Down Plug-in Connector (028-9352-xx)
(1) 5V DC 1.2A Power Supply (025-0165-xx)
(1) Cable Tie (014-0071-xx)
(1) Quick Reference Guide (this document)
Specifications
Environmental
Temperature
32° to 104° F (0° to 40°C)
Humidity
10% to 90% (non-condensing)
Dimensions and Weight (Product)
Height
0.64 in (1.62 cm)
Width
2.70 in (6.85 cm)
Depth
2.67 in (6.78 cm)
Weight
Net: 0.25 lb (0.11 kg)
Shipping: 1.50 lb (0.68 kg)
Power
Input Power
5V DC 1.2A
Max Power
6 watts
Standards
Wireless
Wi-Fi (802.11 b/g/n 2.4 GHz)
Security
WPA™, WPA2™, WPA/WPA2™, WEP
Regulatory
Safety and Emissions
FCC Part 15 | CE Mark | C-Tick
Contains FCC ID:
TLZ-CU277
Contains IC:
6100A-CU277
RoHS
Compliant
Minimum Supported Release
Savant OS
da Vinci 8.2
Network Requirements
Savant requires the use of a wireless network that is configured to
make use of at least one of the supported wireless Standards
listed in the Specifications Table.
Connect all Savant devices to the same local area network (LAN)
or subnet as the host. Savant recommends not implementing any
type of traffic or packet shaping in your network topology for the
Savant devices as this may interfere with performance.
Network Configuration
To ensure that the IP Address will not change due to a power
outage, a static IP Address or DHCP reservation should be
configured. Savant recommends using DHCP reservation within
the router. By using this method, static IP Addresses for all
devices can be managed from a single UI avoiding the need to
access devices individually.
Setting DHCP reservation varies from router to router. Refer to
the documentation for the router to configure DHCP reservation.
Connecting to a Wireless Network
Refer to the SmartControl RS232 – Wi-Fi Smart Controller with 2
RS232 Deployment Guide located on the Savant Customer
Community to connect the SSC-W02R to the local network.
Front Panel
Press and hold for 5 seconds while powered On to clear network
settings. Status LED will blink rapidly when reset is complete.
Off: No Power
On Solid: Connected/Communicating with the system Host.
Blinks Once: In Access Point Provisioning Mode. Ready to be
provisioned to the local network.
Blinks Twice: Establishing connection with the local network.
Blinks Three Times: Connected to the local network. Is
connecting to the host.
Short Off Blink: Firmware is updating.
Rapid Blink: The reset button was held down for at least five
seconds and the SSC-W02R is performing a factory reset.
Rear Panel
RS-232 Port 1 - 6-Pin Plug-In Connector (Left 3 Pins)
G
Signal Ground
Tx
Transmit Data
Rx
Receive Data
RS-232 Port 2 - 6-Pin Plug-In Connector (Right 3 Pins)
G
Signal Ground
Tx
Transmit Data
Rx
Receive Data
Input Power
5V DC 1.2A Connect to included power supply.
Cable Lance
Use with included cable tie to secure power supply
connection.
!
A
B
A
B
C
D

SSC-W02R-00 | 009-1373-03 | 161104!
!
!
!
45 Perseverance Way, Hyannis, MA 02601!
Copyright © 2016 Savant Systems, LLC
2
of
2!
Savant.com | 508.683.2500
RS-232 Wiring and Connections
A 6-pin screw down type connector is included with each SSC-
W02R controller. This connector plugs into the connection on the
rear of the controller.
1.!Remove Power if power is applied.
2.!Pull to remove the terminal block from the rear of the
controller.
3.!With a small flat bladed screwdriver, turn the screws on the top
of connector counterclockwise until the silver crimps in the
front of the connector opens enough to slide the wire(s) into
the square slots.
4.!Insert the stripped wires from the first RS-232 device into ports
1, 2, and 3 observing the correct signals. Do not allow more
than ½inch of bare wire exposed.
5.!Turn the screws clockwise until the screw tightens around the
wire. Tug on the wire a bit to verify the wires are installed
securely.
6.!Continue till all wires are installed.
7.!Repeat steps 3 - 5 for the second RS-232 device.
8.!Plug terminal block back into the rear of the controller.
9.!Reapply power.
Additional Documentation
Additional Documentation is available on the Savant Customer
Community.
•!SmartControl RS232 – Wi-Fi Smart Controller with 2 RS232
Deployment Guide - 009-1374-xx
•!RS-232 Conversion to DB-9 and RS-422/485 Pin out:
Application Note
Regulatory
The following statements are applicable to the SSC-W02R.
FCC Regulations:
15.19. These devices comply with part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) These devices may not cause harmful
interference, and (2) these devices must accept any interference received,
including interferences that may cause undesired operation.
15.21. The changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate the
equipment.
15.105. This equipment has been tested and found to comply with the limits for
CLASS B digital device, pursuant to Part 15 of FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when
the equipment is operated in a residential environment. This equipment
generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference
to radio communications, However there is no guarantee that interference will
not occur in a particular installation, If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving circuit different from that to which receiver
is connected.
- Increase the separation between the equipment and the receiver.
- Consult the dealer or experienced radio/TV technician for help.
IC Regulations:
RSS-Gen 7.1.3. These devices comply with Industry Canada license-exempt
RSS standard(s). Operation is subject to the following two conditions: (1)
These devices may not cause interference, and (2) These devices must accept
any interference, including interference that may cause undesired operation of
the device.
RSS-21- Annexe 9: A 9.4. Le présent appareil est conforme aux CNR d'Industrie
Canada applicables aux appareils radio exempts de licence. L'exploitation est
autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de
brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d'en compromettre
le fonctionnement.