Savant SmartControl 2 User manual

Box Contents
(1) SmartControl 2 (SSC-W002G-00)
(1) Installation Kit SmartControl 2 (075-0174-xx)
(1) Mounting Plate (074-0569-xx)
(1) 6-pin Screw Down Plug-in Connector (028-9352-xx)
(1) 5V DC 1.2A Power Supply (025-0165-xx)
(1) Cable Tie (014-0071-xx)
(1) Quick Reference Guide (this document)
Specifications
Environmental
Environmental
Temperature
32° to 104° F (0° to 40° C)
Humidity
10% to 80% RH (non-condensing)
Dimensions and Weight
Dimensions and Weight
Height
0.64 in (1.62 cm)
Width
2.70 in (6.85 cm)
Depth
2.67 in (6.78 cm)
Weight
Net: 0.25 lb (0.11 kg)
Weight
Shipping: 1.50 lb (0.68 kg)
Power
Power
Input Power
5V DC 1.2A
Max Power
6 watts
Standards
Standards
Wireless
Wi-Fi (802.11 b/g/n 2.4 GHz)
Security
WPA1™, WPA2™, WPA1™ + WPA2™, WEP
Regulatory
Regulatory
Safety and Emissions
FCC Part 15 | CE Mark | C-Tick
Contains FCC ID:
TLZ-CU277
Contains IC:
6100-CU277
RoHS
Compliant
Minimum Supported Release
Minimum Supported Release
Savant OS
da Vinci 7.0
Network Requirements
Savant requires the use of a wireless network that is configured to
make use of at least one of the supported wireless Standards listed in
the Specifications Table.
Connect all Savant devices to the same local area network (LAN) or
subnet as the host. Savant recommends not implementing any type of
traffic or packet shaping in your network topology for the Savant
devices as this may interfere with performance.
Network Configuration
To ensure that the IP Address will not change due to a power outage, a
static IP Address or DHCP reservation should be configured. Savant
recommends using DHCP reservation within the router. By using this
method, static IP Addresses for all devices can be managed from a
single UI avoiding the need to access devices individually.
Setting DHCP reservation varies from router to router. Refer to the
documentation for the router to configure DHCP reservation.
Connecting to a Wireless Network
Refer to the SmartControl 2 (SSC-W002G) Deployment Guide located
on the Savant Customer Community to connect the SSC-W002G to
the network.
Front Panel
A
Press and hold for 5 seconds while powered On to clear network
settings. Status LED will blink rapidly when reset is complete.
Off:No Power
On Solid: Connected/Communicating with the Savant host.
Blinks Once: In Access Point Provisioning Mode and is ready to
be provisioned onto the local network.
Blinks Twice: Is connecting to the local network.
B
Blinks Three Times: Is connecting to the host.
Short OffBlink: Firmware is updating.
Rapid Blink: The reset button was held down for at least five
seconds and the SSC-W002G is performing a factory reset.
Rear Panel
GPIO (General Purpose Input and Output Ports)
6-pin Screw Down Plug-in Connector (Left 3 Pins).
See GPIO and Relay Wiring for pinouts.
GPIO (General Purpose Input and Output Ports)
6-pin Screw Down Plug-in Connector (Left 3 Pins).
See GPIO and Relay Wiring for pinouts.
GPIO Input
When configured as an input, the processor will
look for a low (<0.8V DC) or high (>2.4V DC )
state.
Minimum 0V DC / Maximum 12V DC
GPIO Output
When configured as an output, the port provides
a binary output of 0-12V DC 150mA max.
Normally Open / Normally Closed - Relays
6-pin Screw Down Plug-in Connector (Right 3 Pins)
Normally Open / Normally Closed - Relays
6-pin Screw Down Plug-in Connector (Right 3 Pins)
Relay
Dry contacts (normally open/normally closed) to
control devices requiring basic on/offoperation.
Max: 30V DC 1A.
Input Power
5V DC 1.2A Connect to included power supply.
Cable Lance
Use with included cable tie to secure power
supply connection.
SSC-W002G-00 | 009-1257-01 | 160210
45 Perseverance Way, Hyannis, MA 02601
Copyright © 2016 Savant Systems, LLC
1
of
2
Savant.com | 508.683.2500
Savant® SmartControl 2
Quick Reference Guide
For Product Info

GPIO and Relay Wiring
General Purpose Input/Outputs (GPIO) are binary I/O ports used on
Savant® controllers used to trigger an action within the system. Events
can be the control of a device, such as turning on an amplifier (output)
or detecting a state change for a device (input) to perform a workflow.
The left 3 pins of the supplied 6-pin Screw Down Plug-in Connector are
used for GPIO connections.
Relays are used when a contact closure (normally open or normally
closed) is needed to activate a device. An action such as raising or
lowering shades, opening or closing a gate, or sending control signals
to an HVAC system are a few examples. The right 3 pins of the supplied
6-pin Screw Down Plug-in Connector are used for Relay connections.
GPIO Pull Down Resistor (PD) Usage
GPIO pins are configured as inputs and are pulled high to 12V while the
host is booting up. To make the GPIO signal low during a host reboot
and/or a power cycle, attach the GPIO 1 pin to the PD pin. The PD pin is
a 1K ohm pull down resistor (to signal ground)which keeps the GPIO
output below 0.8V during processor boot times.
Making Connections
1. Remove Power if power is applied.
2. Pull to remove the terminal block from the rear of the controller.
3. With a small flat bladed screwdriver, turn the screws on the top of
connector counterclockwise until the silver crimps in the front of the
connector opens enough to slide the wires into the square slots.
4. Insert one of the stripped wires from the devices being controlled
into its respective slot in the connector. Refer to the diagrams above.
5. Turn the screw clockwise until the screw tightens around the wire.
Tug on the wire a bit to verify it is installed securely. Do not allow
more than 1/2 inch of stripped wire exit from the rear of the
connector.
6. Repeat for each wire till all wires are installed.
7. Plug terminal blocks back into rear of the controller.
8. Reapply power.
Additional Documentation
Additional Documentation is available on the Savant Customer
Community.
•SmartControl 2 (SSC-W002G) Deployment Guide - 009-1273-xx
•Relay and General Purpose Input/Output Profiles: Application Note
•Savant Controllers Family video in the Savant University pages
Regulatory
The following statements are applicable to the Savant SmartControl 2
SSC-W002G controller.
FCC Regulations:
15.19. These devices comply with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) These devices may not
cause harmful interference, and (2) these devices must accept any
interference received, including interferences that may cause
undesired operation.
15.21. The changes or modifications not expressly approved by the
party responsible for compliance could void the user's authority to
operate the equipment.
15.105. This equipment has been tested and found to comply with the
limits for CLASS B digital device, pursuant to Part 15 of FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a residential
environment. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications,
However there is no guarantee that interference will not occur in a
particular installation, If this equipment does cause harmful
interference to radio or television reception, which can be determined
by turning the equipment offand on, the user is encouraged to try to
correct the interference by one or more of the following measures:
- Reorient or relocate the receiving circuit different from that to which
receiver is connected.
- Increase the separation between the equipment and the receiver.
- Consult the dealer or experienced radio/TV technician for help.
IC Regulations:
RSS-Gen 7.1.3. These devices comply with Industry Canada license-
exempt RSS standard(s). Operation is subject to the following two
conditions: (1) These devices may not cause interference, and (2)
These devices must accept any interference, including interference
that may cause undesired operation of the device.
RSS-21- Annexe 9: A 9.4. Le présent appareil est conforme aux CNR
d'Industrie Canada applicables aux appareils radio exempts de licence.
L'exploitation est autorisée aux deux conditions suivantes: (1)
l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de
l'appareil doit accepter tout brouillage radioélectrique subi, même si
le brouillage est susceptible d'en compromettre le fonctionnement.
SSC-W002G-00 | 009-1257-01 | 160210
45 Perseverance Way, Hyannis, MA 02601
Copyright © 2016 Savant Systems, LLC
2
of
2
Savant.com | 508.683.2500